Today's Message Index:
----------------------
1. 05:34 AM - G3I for IO540 (Generation 3 Ignition)
2. 06:12 AM - Rocket-List: Generation 3 Ignition (Generation 3 Ignition)
3. 08:19 AM - Re: Kit Shipments (steve)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hello Dave,
Yes, with the G3i system, the Multiple Spark Discharge is energized
while starting, thus taking place of the Slick Start/ Bendix Shower of
Sparks. Also, both mags are energize while starting.
Yes, a single system runs both (L&R) magnetos.
Sincerely,
Thomas Shpakow
Interfacing Aircraft Magnetos
Electronic Multiple Spark Technology
GENERATION 3 IGNITION
2331 W. Hampden Ave. 130
Englewood, CO. 80110
T 303-781-9449
C 303-906-6846
F 303-806-5120
www.g3ignition.com
mail@g3ignition.com
----- Original Message -----
Sent: Saturday, March 28, 2009 10:04 AM
Subject: G3I for IO540
Does your system eliminate the Slickstart requirement? Does a single
system cover both mags?
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Rocket-List: Generation 3 Ignition |
Hello John,
The total mag height should not be increased, the coil stud terminal is
.500". Usally the height of the ignition harness or p-leads looming
around is the problem.
Are your Bendix 20-series or 1200 's mags, if there 20-series do they
have the flat top steel cover? I've attached a pic of Larry Vetterman's
flat top mag installed with the coil terminal stud. If you go to the
www.g3ignition.com a look @ the G3i pdf install manual, there are more
examples and mods.
The G3i system will eliminate the shower of sparks. It will receive the
retard contacts signal while cranking and will retard/energize both mags
@ start-up. (Drawing # 2 in manual)
Sincerely,
Thomas Shpakow
Interfacing Aircraft Magnetos
Electronic Multiple Spark Technology
GENERATION 3 IGNITION
2331 W. Hampden Ave. 130
Englewood, CO. 80110
T 303-781-9449
C 303-906-6846
F 303-806-5120
www.g3ignition.com
mail@g3ignition.com
----- Original Message -----
Sent: Saturday, March 28, 2009 5:21 PM
Subject: Re: Rocket-List: Generation 3 Ignition
Dear Thomas,
I have been following the string of communication on Rocket List...
I'm interested in adding your system.
My Rocket is equipped with non-impulse type mags and Bendix "Shower of
Sparks" ignition. Also, does your mod increase mag depth in any way ?
I have minimum space between mag (head and wiring) and the firewall.
Thanks for any info you might give.
In a message dated 3/28/2009 6:06:56 A.M. Pacific Daylight Time,
mail@g3ignition.com writes:
Hello Dave,
All mags should be inspected @ the recommended time interval.
Example, I have inspected Slick mags with 400hrs on them and they were
excellent for the G3i system modification. Depending on what fails in
the mag, in some scenarios, the electronic will back -up the mag and
continue to fire just fine. During run-up, a system off, normal (L-R)
mag drop is recommended to revel any potential ignition problems. We do
the mag modification here and inspections/ repairs. Since the spark plug
gap is slightly larger than the stock (.018") recommendation. New total
air gap being increased to .020" - .026" the secondary voltage range to
ionize the spark adds roughly .2 - .5kv to the overall window. It is the
synchronized multiple discharge that make the G3i systems performs so
well. Here is a link to Larry Vettermans/ Vettermans Exhaust website
scroll down to Hartzell Blended Airfoil vs Whirlwind 200RV Series props
on my RV-7A.Larry Vetterman for info. on his test findings or
give him a call.
Sincerely,
Thomas Shpakow
-------------------------------------------------------------------------
-----
A Good Credit Score is 700 or Above. See yours in just 2 easy steps!
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Kit Shipments |
Hi John,
-
I used Partains to ship a qb RV7 fuse.- Couldn't have been better.- Dur
ing the ordering process they communicated well via email and phone.- Enr
oute, the driver gave me updates via his cell phone.- At the house, he kn
ew exactly how to take care of an airplane in unloading.- I offered him c
offee and brownies.- It was late, and I wish I would have offered him a s
hower and bed.- I guess some guys have tipped the driver like twenty buck
s or so.
Oh, the price was right also.- Had I known they also deliver finish kits
etc. I would have used them again.-
-
Steve
--- On Sat, 3/28/09, John Fasching <n1cxo320@salidaco.com> wrote:
From: John Fasching <n1cxo320@salidaco.com>
Subject: RV-List: Kit Shipments
Can you private message me regarding your experience with Partain shipping
your kits...particularly in regard to communications with them, delays, and
any other perteninet infor in confidence. Thank you
-
John
-n1cxo320@salidaco.com
=0A=0A=0A
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|