---------------------------------------------------------- RV-List Digest Archive --- Total Messages Posted Thu 11/19/09: 18 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:26 AM - Re: elevator trim, manual vs electric (Mike Divan) 2. 07:27 AM - Re: Sam James Cowl (Richard Martin) 3. 07:58 AM - Re: elevator trim, manual vs electric (Ralph Finch) 4. 08:15 AM - Re: elevator trim, manual vs electric (Richard Martin) 5. 08:22 AM - Re: elevator trim, manual vs electric (Kelly McMullen) 6. 08:23 AM - Re: elevator trim, manual vs electric (thomas sargent) 7. 09:10 AM - PC to LASAR ignition test cable. (Tom Wright) 8. 11:24 AM - Re: PC to LASAR ignition test cable. (Ralph E. Capen) 9. 11:24 AM - Re: elevator trim, manual vs electric (Bob Collins) 10. 11:51 AM - Re: PC to LASAR ignition test cable. (Tom Wright) 11. 12:46 PM - Re: PC to LASAR ignition test cable. (Linn Walters) 12. 01:24 PM - Re: PC to LASAR ignition test cable. (Tom Wright) 13. 01:25 PM - Re: PC to LASAR ignition test cable. (Ralph E. Capen) 14. 05:44 PM - Re: PC to LASAR ignition test cable. (RV6 Flyer) 15. 06:14 PM - Re: PC to LASAR ignition test cable. (Ralph E. Capen) 16. 07:46 PM - Re: PC to LASAR ignition test cable. (RV6 Flyer) 17. 08:20 PM - Tip Up Canopy Question (Norman Hunger) 18. 10:55 PM - Re: Tip Up Canopy Question (mr.gsun@gmail.com) ________________________________ Message 1 _____________________________________ Time: 05:26:23 AM PST US From: Mike Divan Subject: Re: RV-List: elevator trim, manual vs electric On my flying RV6 Manual aileron trim = love it Electric Elevator trim = HATE IT! If I ever finish my RV7 both will be manual Mike Divan N64GH - RV6 (flying) http://n64gh.blogspot.com/ FREEDOM IS NOT FREE - THANK THE AMERICAN SOLDIER FOR YOURS! Remember it is the Soldier, Sailor, Airman, Marine and Coast Guard that guarantee your freedom NOT the "community organizer"! ________________________________ ________________________________ Message 2 _____________________________________ Time: 07:27:41 AM PST US From: "Richard Martin" Subject: Re: RV-List: Sam James Cowl I converted to a sam James cowl and plenum chamber after approx. 500 hours with the Vans cowl. The james cowl cools better, and my airspeed increased an average of 10 knots. The down side is that you will need a propeller with a 2 inch extended hub. I do not have time to discuss this on the internet. I will be happy to talk to any of you via telephone. anytime. Call 920 619 6968. Dick Martin RV8 N233M the fast one ----From: "Norman Hunger" Sent: Sunday, November 15, 2009 11:40 PM Subject: RV-List: Sam James Cowl > > How many people are flying with Sam James Cowls? > Is everyone happy? > > Are they lighter than stock? > Are they faster than stock? > Do they cool enough? > > Thanks, > Norman Hunger > RV6A Delta BC > Do not archive > > > ________________________________ Message 3 _____________________________________ Time: 07:58:04 AM PST US From: "Ralph Finch" Subject: RE: RV-List: elevator trim, manual vs electric Can you explain further? Please? RF From: owner-rv-list-server@matronics.com [mailto:owner-rv-list-server@matronics.com] On Behalf Of Mike Divan Sent: Thursday, November 19, 2009 5:22 AM Subject: Re: RV-List: elevator trim, manual vs electric On my flying RV6 Manual aileron trim = love it Electric Elevator trim = HATE IT! If I ever finish my RV7 both will be manual ________________________________ Message 4 _____________________________________ Time: 08:15:20 AM PST US From: "Richard Martin" Subject: Re: RV-List: elevator trim, manual vs electric I have 2000 plus hours on my RV8 with the electric trim on aeleron and elevater. I installed a 4 position top hat switch on the top of the control stick for easy operation. The only mod was to install a speed reducer on the elevator trim motor. It was an easy install. The speed reducer is necessaary on the elevator inorder to fine tune elevator cruise position. The aeleron trim allows me to use all of the fuel from each tank at one time on long trips . It is nice to know exactly when a tank is out on a long trip. I did not use tabs for the trim. I cut sections from the trailing edge and made new pieces that are hinged as a part of the aeleron /eleator. Nothing sticks out. It takes time to do this, but i found it well worth the effort. Dick Martin RV8 N233M IO-390 the fast one ----- Original Message ----- From: thomas sargent To: rv-list Sent: Wednesday, November 18, 2009 11:19 AM Subject: RV-List: elevator trim, manual vs electric I am doing final assembly on a 6A. I've never had the trim cable fully installed before and am running into various problems that have me reconsidering things. The manual trim has the advantage that it is not electric - no wiring, no dependence on the electrical system. I also like the very positive connection from my hand to the trim tab. But, (I'm guessing here) the electric looks like it's a lot easier to install. It's probably also a lot lighter. Though, I've heard lots of stories about the servo's running away. Have any of you converted from manual trim to electric? Is the electric easier to install/live with? -- Tom Sargent ________________________________ Message 5 _____________________________________ Time: 08:22:42 AM PST US From: Kelly McMullen Subject: Re: RV-List: elevator trim, manual vs electric Well, Vans eliminated the choice for the RV-10. Electric elevator trim only. Mike Divan wrote: > On my flying RV6 > Manual aileron trim = love it > Electric Elevator trim = HATE IT! > If I ever finish my RV7 both will be manual > ________________________________ Message 6 _____________________________________ Time: 08:23:26 AM PST US Subject: Re: RV-List: elevator trim, manual vs electric From: thomas sargent Thanks for all the useful responses on the trim issue. I guess the easiest thing for me to do is to stick with the manual trim. I'm most of the way down that road, so I will continue in that direction. -- Tom Sargent ________________________________ Message 7 _____________________________________ Time: 09:10:36 AM PST US Subject: RV-List: PC to LASAR ignition test cable. From: Tom Wright Hi, My IO-360 has a LASAR ignition that has failed. I am looking for the PC to LASAR box cable to run troubleshooting. I would like to buy or rent this cable...does anyone have one?? Thanks, Tom Wright 203-551-0746 PRIVACY NOTICE: The information contained in this e-mail (and in any included attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. 2510-2521, and is legally privileged. In addition, it is confidential and intended only for the use of the recipient(s) named above. The review, dissemination, distribution, copying or other use of this information by or to anyone other than the intended recipient is strictly prohibited. If you have received this communication in error, please notify us immediately and delete this message from your system. Thank you. ________________________________ Message 8 _____________________________________ Time: 11:24:14 AM PST US From: "Ralph E. Capen" Subject: Re: RV-List: PC to LASAR ignition test cable. I'm interested in this - just in case. I have a LASAR system in my 6A and knock on wood it's currently fine. I would be willing to build a cable if someone has the pinouts... Ralph Capen -----Original Message----- >From: Tom Wright >Sent: Nov 19, 2009 11:52 AM >To: RV List >Subject: RV-List: PC to LASAR ignition test cable. > >Hi, My IO-360 has a LASAR ignition that has failed. I am looking for the >PC to LASAR box cable to run troubleshooting. I would like to buy or rent >this cable...does anyone have one?? > >Thanks, >Tom Wright 203-551-0746 > >PRIVACY NOTICE: The information contained in this e-mail (and in any included >attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. > 2510-2521, and is legally privileged. In addition, it is confidential and intended >only for the use of the recipient(s) named above. The review, dissemination, >distribution, copying or other use of this information by or to anyone other than the >intended recipient is strictly prohibited. If you have received this communication in >error, please notify us immediately and delete this message from your system. >Thank you. ________________________________ Message 9 _____________________________________ Time: 11:24:14 AM PST US From: "Bob Collins" Subject: RE: RV-List: elevator trim, manual vs electric I have manual trim and am not flying yet. But one thing it kinda hoses up is wiring runs. One of the holes on the left side of the tunnel in my RV-7a is dedicated to a big manual trim cable (and also an ELT wiring run. ) I don't have much electrical stuff in the plane but the hole right side of the tunnel is full up with two strobe cables, a strobe power cable, a nav light cable, and an ELT instrument panel light cable. I could sure use some more room back there. and I havne't even run any antenna cables yet. _____ From: owner-rv-list-server@matronics.com [mailto:owner-rv-list-server@matronics.com] On Behalf Of Ralph Finch Sent: Thursday, November 19, 2009 9:40 AM Subject: RE: RV-List: elevator trim, manual vs electric Can you explain further? Please? RF From: owner-rv-list-server@matronics.com [mailto:owner-rv-list-server@matronics.com] On Behalf Of Mike Divan Sent: Thursday, November 19, 2009 5:22 AM Subject: Re: RV-List: elevator trim, manual vs electric On my flying RV6 Manual aileron trim = love it Electric Elevator trim = HATE IT! If I ever finish my RV7 both will be manual ________________________________ Message 10 ____________________________________ Time: 11:51:51 AM PST US Subject: Re: RV-List: PC to LASAR ignition test cable. From: Tom Wright It has to be fairly simple...8 pins. I could build one also if I just had the pin outs. BTW, I have put 300 hours on my RV-8 and it has worked great but it (LASAR) suddenly quit in cruise flight...everything is connected and the LASAR rep says to get the cable and readout the diagnostic. Cable is ridiculous at $160. I wish I could rent one...then I would make my own. On Thu, Nov 19, 2009 at 12:47 PM, Ralph E. Capen wro te: > > I'm interested in this - just in case. > > I have a LASAR system in my 6A and knock on wood it's currently fine. > > I would be willing to build a cable if someone has the pinouts... > > Ralph Capen > > -----Original Message----- > >From: Tom Wright > >Sent: Nov 19, 2009 11:52 AM > >To: RV List > >Subject: RV-List: PC to LASAR ignition test cable. > > > >Hi, My IO-360 has a LASAR ignition that has failed. I am looking for t he > >PC to LASAR box cable to run troubleshooting. I would like to buy or re nt > >this cable...does anyone have one?? > > > >Thanks, > >Tom Wright 203-551-0746 > > > >PRIVACY NOTICE: The information contained in this e-mail (and in any > included > >attachments) is covered by the Electronic Communications Privacy Act, 18 > U.S.C. > >=A7=A7 2510-2521, and is legally privileged. In addition, it is confiden tial > and intended > >only for the use of the recipient(s) named above. The review, > dissemination, > >distribution, copying or other use of this information by or to anyone > other than the > >intended recipient is strictly prohibited. If you have received this > communication in > >error, please notify us immediately and delete this message from your > system. > >Thank you. > > =========== =========== =========== =========== > > PRIVACY NOTICE: The information contained in this e-mail (and in any incl uded attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. =A7=A7 2510-2521, and is legally privileged. In addition, it is confident ial and intended only for the use of the recipient(s) named above. The review, disseminati on, distribution, copying or other use of this information by or to anyone ot her than the intended recipient is strictly prohibited. If you have received this comm unication in error, please notify us immediately and delete this message from your sys tem. Thank you. ________________________________ Message 11 ____________________________________ Time: 12:46:40 PM PST US From: Linn Walters Subject: Re: RV-List: PC to LASAR ignition test cable. I hate to suggest the obvious, but have you asked the LASAR folks for the pinout of the cable??? Linn Tom Wright wrote: > It has to be fairly simple...8 pins. I could build one also if I just > had the pin outs. BTW, I have put 300 hours on my RV-8 and it has > worked great but it (LASAR) suddenly quit in cruise flight...everything > is connected and the LASAR rep says to get the cable and readout the > diagnostic. Cable is ridiculous at $160. I wish I could rent > one...then I would make my own. > > On Thu, Nov 19, 2009 at 12:47 PM, Ralph E. Capen > wrote: > > > > > I'm interested in this - just in case. > > I have a LASAR system in my 6A and knock on wood it's currently fine. > > I would be willing to build a cable if someone has the pinouts... > > Ralph Capen > > -----Original Message----- > >From: Tom Wright > > >Sent: Nov 19, 2009 11:52 AM > >To: RV List > > >Subject: RV-List: PC to LASAR ignition test cable. > > > >Hi, My IO-360 has a LASAR ignition that has failed. I am looking > for the > >PC to LASAR box cable to run troubleshooting. I would like to buy > or rent > >this cable...does anyone have one?? > > > >Thanks, > >Tom Wright 203-551-0746 > > > >PRIVACY NOTICE: The information contained in this e-mail (and in > any included > >attachments) is covered by the Electronic Communications Privacy > Act, 18 U.S.C. > > 2510-2521, and is legally privileged. In addition, it is > confidential and intended > >only for the use of the recipient(s) named above. The review, > dissemination, > >distribution, copying or other use of this information by or to > anyone other than the > >intended recipient is strictly prohibited. If you have received > this communication in > >error, please notify us immediately and delete this message from > your system. > >Thank you. > > > > > > ========== > ="_blank">www.aeroelectric.com > ooks.com" target="_blank">www.buildersbooks.com > et="_blank">www.homebuilthelp.com > ="_blank">http://www.matronics.com/contribution > le, List Admin. > ========== > get="_blank">http://www.matronics.com/Navigator?RV-List > ========== > http://forums.matronics.com > ========== > > > > > PRIVACY NOTICE: The information contained in this e-mail (and in any included > attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. > 2510-2521, and is legally privileged. In addition, it is confidential and intended > only for the use of the recipient(s) named above. The review, dissemination, > distribution, copying or other use of this information by or to anyone other than the > intended recipient is strictly prohibited. If you have received this communication in > error, please notify us immediately and delete this message from your system. > Thank you. > > > > * > > > * ________________________________ Message 12 ____________________________________ Time: 01:24:56 PM PST US Subject: Re: RV-List: PC to LASAR ignition test cable. From: Tom Wright Actually no...great idea, i just assumed they wouldn't provide it but of course it never hurts to ask. On Thu, Nov 19, 2009 at 2:59 PM, Linn Walters wr ote: > > I hate to suggest the obvious, but have you asked the LASAR folks for the > pinout of the cable??? > Linn > > Tom Wright wrote: > >> It has to be fairly simple...8 pins. I could build one also if I just h ad >> the pin outs. BTW, I have put 300 hours on my RV-8 and it has worked gr eat >> but it (LASAR) suddenly quit in cruise flight...everything is connected and >> the LASAR rep says to get the cable and readout the diagnostic. Cable i s >> ridiculous at $160. I wish I could rent one...then I would make my own. >> >> On Thu, Nov 19, 2009 at 12:47 PM, Ralph E. Capen > recapen@earthlink.net>> wrote: >> >> > >> >> >> I'm interested in this - just in case. >> >> I have a LASAR system in my 6A and knock on wood it's currently fine. >> >> I would be willing to build a cable if someone has the pinouts... >> >> Ralph Capen >> >> -----Original Message----- >> >From: Tom Wright > >> >Sent: Nov 19, 2009 11:52 AM >> >To: RV List > >> >Subject: RV-List: PC to LASAR ignition test cable. >> > >> >Hi, My IO-360 has a LASAR ignition that has failed. I am looking >> for the >> >PC to LASAR box cable to run troubleshooting. I would like to buy >> or rent >> >this cable...does anyone have one?? >> > >> >Thanks, >> >Tom Wright 203-551-0746 >> > >> >PRIVACY NOTICE: The information contained in this e-mail (and in >> any included >> >attachments) is covered by the Electronic Communications Privacy >> Act, 18 U.S.C. >> >=A7=A7 2510-2521, and is legally privileged. In addition, it is >> >> confidential and intended >> >only for the use of the recipient(s) named above. The review, >> dissemination, >> >distribution, copying or other use of this information by or to >> anyone other than the >> >intended recipient is strictly prohibited. If you have received >> this communication in >> >error, please notify us immediately and delete this message from >> your system. >> >Thank you. >> >> >> >> >> >> ========== >> ="_blank">www.aeroelectric.com >> ooks.com" target="_blank">www.buildersbooks.com >> et="_blank">www.homebuilthelp.com >> ="_blank">http://www.matronics.com/contribution >> le, List Admin. >> ========== >> get="_blank">http://www.matronics.com/Navigator?RV-List >> ========== >> http://forums.matronics.com >> ========== >> >> >> >> >> >> PRIVACY NOTICE: The information contained in this e-mail (and in any >> included >> attachments) is covered by the Electronic Communications Privacy Act, 18 >> U.S.C. >> =A7=A7 2510-2521, and is legally privileged. In addition, it is confiden tial >> and intended >> >> only for the use of the recipient(s) named above. The review, >> dissemination, >> distribution, copying or other use of this information by or to anyone >> other than the >> intended recipient is strictly prohibited. If you have received this >> communication in >> error, please notify us immediately and delete this message from your >> system. >> Thank you. >> >> >> >> * >> >> >> * >> > > =========== =========== =========== =========== > > PRIVACY NOTICE: The information contained in this e-mail (and in any incl uded attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. =A7=A7 2510-2521, and is legally privileged. In addition, it is confident ial and intended only for the use of the recipient(s) named above. The review, disseminati on, distribution, copying or other use of this information by or to anyone ot her than the intended recipient is strictly prohibited. If you have received this comm unication in error, please notify us immediately and delete this message from your sys tem. Thank you. ________________________________ Message 13 ____________________________________ Time: 01:25:09 PM PST US From: "Ralph E. Capen" Subject: Re: RV-List: PC to LASAR ignition test cable. Good idea - I was going to look in my reference documentation first. I just started thinking about this from the original post.... Need an afternoon coffee -----Original Message----- >From: Linn Walters >Sent: Nov 19, 2009 2:59 PM >To: rv-list@matronics.com >Subject: Re: RV-List: PC to LASAR ignition test cable. > > >I hate to suggest the obvious, but have you asked the LASAR folks for >the pinout of the cable??? >Linn > >Tom Wright wrote: >> It has to be fairly simple...8 pins. I could build one also if I just >> had the pin outs. BTW, I have put 300 hours on my RV-8 and it has >> worked great but it (LASAR) suddenly quit in cruise flight...everything >> is connected and the LASAR rep says to get the cable and readout the >> diagnostic. Cable is ridiculous at $160. I wish I could rent >> one...then I would make my own. >> >> On Thu, Nov 19, 2009 at 12:47 PM, Ralph E. Capen > > wrote: >> >> > >> >> I'm interested in this - just in case. >> >> I have a LASAR system in my 6A and knock on wood it's currently fine. >> >> I would be willing to build a cable if someone has the pinouts... >> >> Ralph Capen >> >> -----Original Message----- >> >From: Tom Wright > >> >Sent: Nov 19, 2009 11:52 AM >> >To: RV List > >> >Subject: RV-List: PC to LASAR ignition test cable. >> > >> >Hi, My IO-360 has a LASAR ignition that has failed. I am looking >> for the >> >PC to LASAR box cable to run troubleshooting. I would like to buy >> or rent >> >this cable...does anyone have one?? >> > >> >Thanks, >> >Tom Wright 203-551-0746 >> > >> >PRIVACY NOTICE: The information contained in this e-mail (and in >> any included >> >attachments) is covered by the Electronic Communications Privacy >> Act, 18 U.S.C. >> > 2510-2521, and is legally privileged. In addition, it is >> confidential and intended >> >only for the use of the recipient(s) named above. The review, >> dissemination, >> >distribution, copying or other use of this information by or to >> anyone other than the >> >intended recipient is strictly prohibited. If you have received >> this communication in >> >error, please notify us immediately and delete this message from >> your system. >> >Thank you. >> >> >> >> >> >> ========== >> ="_blank">www.aeroelectric.com >> ooks.com" target="_blank">www.buildersbooks.com >> et="_blank">www.homebuilthelp.com >> ="_blank">http://www.matronics.com/contribution >> le, List Admin. >> ========== >> get="_blank">http://www.matronics.com/Navigator?RV-List >> ========== >> http://forums.matronics.com >> ========== >> >> >> >> >> PRIVACY NOTICE: The information contained in this e-mail (and in any included >> attachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C. >> 2510-2521, and is legally privileged. In addition, it is confidential and intended >> only for the use of the recipient(s) named above. The review, dissemination, >> distribution, copying or other use of this information by or to anyone other than the >> intended recipient is strictly prohibited. If you have received this communication in >> error, please notify us immediately and delete this message from your system. >> Thank you. >> >> >> >> * >> >> >> * > > ________________________________ Message 14 ____________________________________ Time: 05:44:48 PM PST US From: RV6 Flyer Subject: RE: RV-List: PC to LASAR ignition test cable. Just a note to the guys located in SoCAL. I have the PC to LASAR controller box cable=2C the T100 tool kit=2C all the factory manuals=2C a current subscription to the manuals=2C the LASAR timi ng light=2C a spare controller box (O-360 w/o CHT)=2C and three spare LASAR mags (one has 25-hours [w/sensor]=2C the other two ~ 500 hours[1-w/sensor =2C 1-w/o sensor). NO I will not ship the cable. I also have never used it. I purchased the cable from Bart at AeroSport Power in Kamloops=2C BC. He an d Sue will give you some of the best prices on LASAR parts/equipment. Gary A. Sobek A&P DAR "My Sanity" RV-6 N157GS O-320 Hartzell=2C 2=2C334+ Flying Hours So. CA=2C USA (hangared KCCB) http://www.rvdar.com Subject: RV-List: PC to LASAR ignition test cable. From: tomw@charterops.com Hi=2C My IO-360 has a LASAR ignition that has failed. I am looking for th e PC to LASAR box cable to run troubleshooting. I would like to buy or ren t this cable...does anyone have one?? Thanks=2C Tom Wright 203-551-0746 PRIVACY NOTICE: The information contained in this e-mail (and in any includ ed attachments) is covered by the Electronic Communications Privacy Act=2C 18 U.S.C. =A7=A7 2510-2521=2C and is legally privileged. In addition=2C it is confide ntial and intended only for the use of the recipient(s) named above. The review=2C disseminati on=2C distribution=2C copying or other use of this information by or to anyone ot her than the intended recipient is strictly prohibited. If you have received this commun ication in error=2C please notify us immediately and delete this message from your sys tem. Thank you. _________________________________________________________________ Windows 7: It works the way you want. Learn more. http://www.microsoft.com/Windows/windows-7/default.aspx?ocid=PID24727::T: WLMTAGL:ON:WL:en-US:WWL_WIN_evergreen:112009v2 ________________________________ Message 15 ____________________________________ Time: 06:14:20 PM PST US From: "Ralph E. Capen" Subject: Re: RV-List: PC to LASAR ignition test cable. Gary, Are you willing to give us the pinout? ----- Original Message ----- From: RV6 Flyer To: RV List Sent: Thursday, November 19, 2009 8:41 PM Subject: RE: RV-List: PC to LASAR ignition test cable. Just a note to the guys located in SoCAL. I have the PC to LASAR controller box cable, the T100 tool kit, all the factory manuals, a current subscription to the manuals, the LASAR timing light, a spare controller box (O-360 w/o CHT), and three spare LASAR mags (one has 25-hours [w/sensor], the other two ~ 500 hours[1-w/sensor, 1-w/o sensor). NO I will not ship the cable. I also have never used it. I purchased the cable from Bart at AeroSport Power in Kamloops, BC. He and Sue will give you some of the best prices on LASAR parts/equipment. Gary A. Sobek A&P DAR "My Sanity" RV-6 N157GS O-320 Hartzell, 2,334+ Flying Hours So. CA, USA (hangared KCCB) http://www.rvdar.com ------------------------------------------------------------------------- ----- Date: Thu, 19 Nov 2009 11:52:54 -0500 Subject: RV-List: PC to LASAR ignition test cable. From: tomw@charterops.com To: rv-list@matronics.com Hi, My IO-360 has a LASAR ignition that has failed. I am looking for the PC to LASAR box cable to run troubleshooting. I would like to buy or rent this cable...does anyone have one?? Thanks, Tom Wright 203-551-0746 PRIVACY NOTICE: The information contained in this e-mail (and in any includedattachments) is covered by the Electronic Communications Privacy Act, 18 U.S.C.=A7=A7 2510-2521, and is legally privileged. In addition, it is confidential and intendedonly for the use of the recipient(s) named above. The review, dissemination,distribution, copying or other use of this information by or to anyone other than theintended recipient is strictly prohibited. If you have received this communication inerror, please notify us immediately and delete this message from your system.Thank you.www.buildersbooks--> http://forums.matronics.co================ ------------------------------------------------------------------------- ----- Windows 7: It works the way you want. Learn more. ________________________________ Message 16 ____________________________________ Time: 07:46:19 PM PST US From: RV6 Flyer Subject: RE: RV-List: PC to LASAR ignition test cable. There is no pin out that I can find in the documentation. They want to SELL you the cable. I have not tried to reverse engineer it and my time is wor th more than the cost of the cable to reverse engineer it. Gary A. Sobek "My Sanity" RV-6 N157GS O-320 Hartzell=2C 2=2C334+ Flying Hours So. CA=2C USA From: recapen@earthlink.net Subject: Re: RV-List: PC to LASAR ignition test cable. Gary=2C Are you willing to give us the pinout? ----- Original Message ----- From: RV6 Flyer To: RV List Sent: Thursday=2C November 19=2C 2009 8:41 PM Subject: RE: RV-List: PC to LASAR ignition test cable. Just a note to the guys located in SoCAL. I have the PC to LASAR controller box cable=2C the T100 tool kit=2C all the fact ory manuals=2C a current subscription to the manuals=2C the LASAR timing ligh t=2C a spare controller box (O-360 w/o CHT)=2C and three spare LASAR mags (one h as 25-hours [w/sensor]=2C the other two ~ 500 hours[1-w/sensor=2C 1-w/o sensor). NO I will not ship the cable. I also have never used it. I purchased the cable from Bart at AeroSport Power in Kamloops=2C BC. He and Sue will give you some of the best prices on LASAR parts/equipment. Gary A. Sobek A&P DAR "My Sanity" RV-6 N157GS O-320 Hartzell=2C 2=2C334+ Flying Hours So. CA=2C USA (hangared KCCB) http://www.rvdar.com Date: Thu=2C 19 Nov 2009 11:52:54 -0500 Subject: RV-List: PC to LASAR ignition test cable. From: tomw@charterops.com rv-list@matronics.com Hi=2C My IO-360 has a LASAR ignition that has failed. I am looking for the PC to LASAR box cable to run troubleshooting. I would like to buy or rent this cable...does anyone have one?? Thanks=2C Tom Wright 203-551-0746 PRIVACY NOTICE: The information contained in this e-mail (and in any includ ed attachments) is covered by the Electronic Communications Privacy Act=2C 18 U.S.C. =A7=A7 2510-2521=2C and is legally privileged. In addition=2C it is confide ntial and intended only for the use of the recipient(s) named above. The review=2C disseminati on=2C distribution=2C copying or other use of this information by or to anyone ot her than the intended recipient is strictly prohibited. If you have received this commun ication in error=2C please notify us immediately and delete this message from your sys tem. Thank you. www.buildersbooks--> http://forums.matronics.co========= ======= Windows 7: It works the way you want. Learn more. href="http://www.aeroelectric.com">www.aeroelectric.com href="http://www.buildersbooks.com">www.buildersbooks.com href="http://www.homebuilthelp.com">www.homebuilthelp.com href="http://www.matronics.com/contribution">http://www.matronics.com/chr ef="http://www.matronics.com/Navigator?RV-List">http://www.matronics.com/ Navigator?RV-List href="http://forums.matronics.com">http://forums.matronics.com _________________________________________________________________ Bing brings you maps=2C menus=2C and reviews organized in one place. http://www.bing.com/search?q=restaurants&form=MFESRP&publ=WLHMTAG&cre a=TEXT_MFESRP_Local_MapsMenu_Resturants_1x1 ________________________________ Message 17 ____________________________________ Time: 08:20:00 PM PST US From: Norman Hunger Subject: RV-List: Tip Up Canopy Question Hi everybody, I last worked on this area many years ago and I think I was planning on building a strip of fiberglass over this whole seam. The holes in the plexi are only countersunk every second hole. Don't know exactly what I had planned but I must move forward and finish this area. I was wondering how many of the tip up guys have bothered to make a fiberglass cover all the way across the back of the canopy? Next up I am going to countersink the plexi and upsize the holes to take the #6 screws I was planning to use as the back edge of the canopy. I hope it will be OK to drill the plexi...... Norman Hunger RV6A Delta BC Do not archive Here's a shot of the two map lights I had put in the canopy frame so long ago.... ________________________________ Message 18 ____________________________________ Time: 10:55:05 PM PST US Subject: Re: RV-List: Tip Up Canopy Question From: mr.gsun@gmail.com My RV-7 tipup does not have a strip of anything along the back side. Looks great except for the bottom corner that vibrated too much when I ran engine & taxied too much with the canopy up on the handle stop for ventilation. I assume the tip of that corner was occasionally hitting the edge of the roll bar or something when the engine vibes or bumps were just right. Anyway, after 300 hours or so, I noticed a 3" piece missing and found it on the taxiway. Glued it back in place and looks OK except for the glue-line. I'll be putting some sort of a aluminum, fiberglass or vinyl all across the back now. I've also put in some little guide pieces to keep the canopy aligned when closing so it cannot hit anything when almost closed. Still learning..... do not archive On Thu, Nov 19, 2009 at 7:32 PM, Norman Hunger wrote: > Hi everybody, I last worked on this area many years ago and I think I was > planning on building a strip of fiberglass over this whole seam. The holes > in the plexi are only countersunk every second hole. Don't know exactly what > I had planned but I must move forward and finish this area. > > I was wondering how many of the tip up guys have bothered to make a > fiberglass cover all the way across the back of the canopy? > > Next up I am going to countersink the plexi and upsize the holes to take > the #6 screws I was planning to use as the back edge of the canopy. I hope > it will be OK to drill the plexi...... > > Norman Hunger > RV6A Delta BC > Do not archive > > > Here's a shot of the two map lights I had put in the canopy frame so long > ago.... > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv-list Browse Digests http://www.matronics.com/digest/rv-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.