Today's Message Index:
----------------------
1. 02:10 AM - Re: RV7-List: Oil Cooler Mount Cracks - Replacement Follow Up... (Hugh Ragg)
2. 05:48 AM - Re: PC 680 Battery (Ed Anderson)
3. 10:59 AM - new paint shop (Randy Pinkston)
4. 10:49 PM - Well, very good (Mike Robertson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV7-List: Oil Cooler Mount Cracks - Replacement Follow Up... |
Nice work, I am very interested in this as my RV7 is almost complete. I looked
at the oil cooler install and will have a very close look at modifying the installation.
Thanks for the valuable feed back
Regards
Hugh
On 25/10/2010, at 10:55 AM, Matt Dralle wrote:
>
> Dear Listers,
>
> First, let me say thanks to everyone that responded to my post regarding the
oil cooler mount cracks. Lots of great feedback; I really appreciate it.
>
> Rather than subject the Oil Cooler's mounts directly to the mounting screw's
tension, I decided to craft some angle brackets that much more evenly distribute
the load over the original mount. I made a set for the front and back of the
rear mount and a single top bracket for the front mount that would sandwich
the Oil Cooler mount to the rear baffle. I very carefully trimmed the tube spacers
to exactly fit between the front and back brackets; much more precisely
than the original installation. The inside rear Oil Cooler mount got the requisite
top and bottom notching to clear the engine mount and this time I hogged
out a bit more to give even better clearance. (A couple of people noted the
scratches on the motor mount near these original notches; I believe these were
from when I was filing the original oil cooler, I got a little over zealous
and scrapped the power coat; I don't believe that there has been any incounters
between the oil cooler and the mount due to engine shake.) I also added a few
more rivets on the flanges between the rear and left-rear baffle sheet metal
pieces.
>
> To absorb some of the engine vibration, crafted a "gasket" of sorts from the
same rubber material the baffle seals are made of. This really seem to nicely
isolate the Oil Cooler from the baffle/engine.
>
> Finally, I crafted a sweet stabilization strut from aluminum tube stock to form
a brace from the engine to the top of the rear engine baffle. This made a
HUGE difference in the overall stiffness of the oil cooler and I'm hoping will
be the final modification in solving this Oil Cooler cracking issue.
>
> Thanks again for all the feedback!
>
>
> -
> Matt Dralle
> RV-8 #82880 N998RV
> http://www.mattsrv8.com - Matt's RV-8 Construction Blog
> http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
> Status: 112+ Hours Total Time Since May 2 2010 Test Flight!
> <2010.10.17 - RV-8 - IO-390 Oil Cooler Mount Cracking (1).jpg><2010.10.17 - RV-8
- IO-390 Oil Cooler Mount Cracking (2).jpg><2010.10.24 - RV-8 - Oil Cooler
Replacement And Remounting (1).jpg><2010.10.24 - RV-8 - Oil Cooler Replacement
And Remounting (2).jpg><2010.10.24 - RV-8 - Oil Cooler Replacement And Remounting
(3).jpg><2010.10.24 - RV-8 - Oil Cooler Replacement And Remounting (4).jpg><2010.10.24
- RV-8 - Oil Cooler Replacement And Remounting (5).jpg><2010.10.24
- RV-8 - Oil Cooler Replacement And Remounting (6).jpg><2010.10.24 - RV-8
- Oil Cooler Replacement And Remounting (7).jpg><2010.10.24 - RV-8 - Oil Cooler
Replacement And Remounting (8).jpg><2010.10.24 - RV-8 - Oil Cooler Replacement
And Remounting (9).jpg>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: PC 680 Battery |
Don, I purchased a PC 680 last month from
www.sportsimportsltd.com
For the price of:
Subtotal 104.95
Shipping
14.17
Tax
0.00
Total
119.12
that was the best price I could find.
Ed
Edward L. Anderson
Anderson Electronic Enterprises LLC
305 Reefton Road
Weddington, NC 28104
http://www.andersonee.com
http://www.eicommander.com
From: Don McCallister
Sent: Sunday, October 24, 2010 7:34 PM
Subject: RV-List: PC 680 Battery
What is the best recent price and dealer for the Odyssey PC-680 today???
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
We have a new paint shop opening @ anson county nc KAFP 50 miles east of
charlotte...Est. price on rv 8 & rv 7 type planes 3 color is about 7995.00
. The guys name is gene mason & he has a lot of years painting ..He painted
my rv7 N705rp in 1995 & still looks great.His # is 704-984-0144...Lets try
to send him so work so we can keep someone close by to paint our great
planes. Randy Pinkston ..can call me also if need 704-438-1222
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Dear friend:
look$B!'(BBeautiful China's online store
I recommend to you a very good shopping site << http://mtzqhk.80.hk>>.
The quality of product is had better, the service is perfect,
and price is had better, the speed of the deliver is very fast.
There are own warehouse and store,
there is customer in the whole world, receive customer very high praise.
MSN: mtzqhk@hotmail.com Email: mtzqhk@188.com
Wish we cooperation delectation !
hey~
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|