Today's Message Index:
----------------------
1. 03:12 PM - Cracks Around Rudder Stiffeners... (Matt Dralle)
2. 03:19 PM - West Coast Formation Clinic (WCFC) This Weekend... (Matt Dralle)
3. 04:14 PM - Re: Cracks Around Rudder Stiffeners... (Ralph E. Capen)
4. 04:56 PM - Re: Cracks Around Rudder Stiffeners... (Dale Ensing)
5. 10:47 PM - Re: West Coast Formation Clinic (WCFC) This Weekend... (RV6 Flyer)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Cracks Around Rudder Stiffeners... |
After washing the 'ol RV-8 last night, I noticed that there is about a .5" crack
in the .02" skin of the rudder in the *front* of two of the angle stiffeners
(towards the leading edge of the rudder). The skin is a little "bulgy" right
there, and its possible that I gave that area a good push with my thumb at some
point to see if I could get it to flatten out.
Obviously I need to keep an eye on this, but is it anything to worry about, really?
I'm just about ready to take the plane in for paint, so if I have to do
something about it, I'd rather do it *before* the paint.
Thanks in advance for the feedback,
-
Matt "Fox" Dralle
RV-8 #82880 N998RV "Ruby Vixen"
http://www.mattsrv8.com - Matt's RV-8 Construction Log
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: 170+ Hours TTSN - Paint job is all that's left...
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | West Coast Formation Clinic (WCFC) This Weekend... |
Any listers planning on attending the WCFC this weekend in Madera California?
I'm planning on being there with the 'ol RV-8. Come up and say 'hi' and introduce
yourself; I'd love to meet some of the Listers in person!
-
Matt "Fox" Dralle
RV-8 #82880 N998RV "Ruby Vixen"
http://www.mattsrv8.com - Matt's RV-8 Construction Log
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: 170+ Hours TTSN - Paint job is all that's left...
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Cracks Around Rudder Stiffeners... |
I'd rebuild it before paint - my .016 rudder skin had a hangar bump which I
covered with microballoons. It got a second bump and I rebuilt it with a
.020 skin - I have on IO360B1F6 so it was recommended anyway.
No regrets and it was a weekend job...the first part I built and the last
part I built.
----- Original Message -----
From: "Matt Dralle" <dralle@matronics.com>
<rv7-list@matronics.com>
Sent: Thursday, April 28, 2011 6:04 PM
Subject: RV-List: Cracks Around Rudder Stiffeners...
>
>
> After washing the 'ol RV-8 last night, I noticed that there is about a .5"
> crack in the .02" skin of the rudder in the *front* of two of the angle
> stiffeners (towards the leading edge of the rudder). The skin is a little
> "bulgy" right there, and its possible that I gave that area a good push
> with my thumb at some point to see if I could get it to flatten out.
>
> Obviously I need to keep an eye on this, but is it anything to worry
> about, really? I'm just about ready to take the plane in for paint, so if
> I have to do something about it, I'd rather do it *before* the paint.
>
> Thanks in advance for the feedback,
>
> -
> Matt "Fox" Dralle
> RV-8 #82880 N998RV "Ruby Vixen"
> http://www.mattsrv8.com - Matt's RV-8 Construction Log
> http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
> Status: 170+ Hours TTSN - Paint job is all that's left...
>
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Cracks Around Rudder Stiffeners... |
I also have some cracks on my 6A rudder. Cracks are on the first rivets of
the stiffeners. Next to the area where the skin is not supported be either
the stiffener or the leading edge spar of the rudder. It appears the skin is
allowed to flex a bit because the stiffeners are not attached to the spar. I
stop drilled each crack when I first discovered them and they have not
progress further in 5 years. It is on my walk around check list and I look
at them every time I fly.
NOTE when I first found the cracks, I called Van's ....before I completed
the explanation of my problem I was stopped by the 'friendly' tech help guy
who said "you must have a big engine on your 6A don't you" I admitted I have
an O-360 with high compression pistons, electronic ignition and constant
speed prop. His next statement "there is your problem!"
I suggest you stop drill the cracks and watch them. If you build a new
rudder before you paint, with no change in the rudder design, you will
probably experience cracks again.
Dale
----- Original Message -----
From: "Matt Dralle" <dralle@matronics.com>
<rv7-list@matronics.com>
Sent: Thursday, April 28, 2011 6:04 PM
Subject: RV-List: Cracks Around Rudder Stiffeners...
>
>
> After washing the 'ol RV-8 last night, I noticed that there is about a .5"
> crack in the .02" skin of the rudder in the *front* of two of the angle
> stiffeners (towards the leading edge of the rudder). The skin is a little
> "bulgy" right there, and its possible that I gave that area a good push
> with my thumb at some point to see if I could get it to flatten out.
>
> Obviously I need to keep an eye on this, but is it anything to worry
> about, really? I'm just about ready to take the plane in for paint, so if
> I have to do something about it, I'd rather do it *before* the paint.
>
> Thanks in advance for the feedback,
>
> -
> Matt "Fox" Dralle
> RV-8 #82880 N998RV "Ruby Vixen"
> http://www.mattsrv8.com - Matt's RV-8 Construction Log
> http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
> Status: 170+ Hours TTSN - Paint job is all that's left...
>
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | West Coast Formation Clinic (WCFC) This Weekend... |
See you there Matt. This will be the 3rd year in a row that we are at Made
ra.
Gary A. Sobek
"My Sanity" RV-6 N157GS O-320 Hartzell=2C
2=2C491+ Flying Hours So. CA=2C USA
> Date: Thu=2C 28 Apr 2011 15:12:16 -0700
> To: rv-list@matronics.com=3B rv8-list@matronics.com=3B rv7-list@matronics
.com=3B rv10-list@matronics.com
> From: dralle@matronics.com
> Subject: RV-List: West Coast Formation Clinic (WCFC) This Weekend...
>
>
>
> Any listers planning on attending the WCFC this weekend in Madera Califor
nia?
>
> I'm planning on being there with the 'ol RV-8. Come up and say 'hi' and
introduce yourself=3B I'd love to meet some of the Listers in person!
>
>
> -
> Matt "Fox" Dralle
> RV-8 #82880 N998RV "Ruby Vixen"
> http://www.mattsrv8.com - Matt's RV-8 Construction Log
> http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
> Status: 170+ Hours TTSN - Paint job is all that's left...
>
>
===========
===========
===========
===========
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|