Today's Message Index:
----------------------
1. 03:59 AM - Re: Looking for someone to work on my RV-6 (William Dean)
2. 06:02 AM - Prop cable throw vs governor throw (Ralph E. Capen)
3. 06:41 AM - Re: Prop cable throw vs governor throw (Carl Froehlich)
4. 08:32 AM - Re: Prop cable throw vs governor throw (Ralph E. Capen)
5. 01:26 PM - Re: Looking for someone to work on my RV-6 (HCRV6@comcast.net)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Looking for someone to work on my RV-6 |
We have gone to Yahoo groups and removed all the groups, how do we get off this
group. My father passed away and we no longer need these emails. Thank you
for any assistance you can provide.
The Dean family
Sent from my iPad
On Nov 17, 2012, at 5:16 PM, N616TB <N616TB@btsapps.com> wrote:
>
> I have a flying RV-6 with over 150 hours. I had an incident landing in grass
where a wheel pant came apart and rotated into the fuel tank. We were able to
patch the tank however, I would like to have a new tank built. I have all the
new parts for a completely new tank. I am looking for someone in Texas who
could do this work as I am in process of moving my shop. I can bring the airplane
to your location.
> Please contact me off list. N616tb at btsapps dot com
>
> Best Regards;
>
> Timothy Bryan
> We are what we repeatedly do. Excellence, therefore, is not an act but a habit.
> Aristotle
>
>
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Prop cable throw vs governor throw |
Folks,
I'm in the final reassembly stages after a derecho/tornado blew the hangar
door in to my prop..prop is rebuilt and engine tore down for inspection.
I have found while verifying my cabling that the prop governor has 1/8" more
throw than my cable. I have it set up so the fine stop matches up but it
won't go all the way coarse.
I'm kinda thinking it doesn't matter as I don't think I have ever had the
prop that far coarse. I can get a custom made cable with the correct throw
- but do I need to?
RV6A
IO360B1F6 LASAR/Injected
MTV12(B) 183-59 hydraulic CS
I'll be sending this to the MT folks as well for their input.
Ralph Capen
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Prop cable throw vs governor throw |
It sounds like you have more than enough movement to govern below 2000 RPM -
call it done.
Carl
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of Ralph E. Capen
Sent: Sunday, November 18, 2012 9:02 AM
Subject: RV-List: Prop cable throw vs governor throw
Folks,
I'm in the final reassembly stages after a derecho/tornado blew the hangar
door in to my prop..prop is rebuilt and engine tore down for inspection.
I have found while verifying my cabling that the prop governor has 1/8" more
throw than my cable. I have it set up so the fine stop matches up but it
won't go all the way coarse.
I'm kinda thinking it doesn't matter as I don't think I have ever had the
prop that far coarse. I can get a custom made cable with the correct throw
- but do I need to?
RV6A
IO360B1F6 LASAR/Injected
MTV12(B) 183-59 hydraulic CS
I'll be sending this to the MT folks as well for their input.
Ralph Capen
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Prop cable throw vs governor throw |
I have been flying it this way for three years...you have a good point!
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of Carl Froehlich
Sent: Sunday, November 18, 2012 9:41 AM
Subject: RE: RV-List: Prop cable throw vs governor throw
It sounds like you have more than enough movement to govern below 2000 RPM -
call it done.
Carl
From: owner-rv-list-server@matronics.com
[mailto:owner-rv-list-server@matronics.com] On Behalf Of Ralph E. Capen
Sent: Sunday, November 18, 2012 9:02 AM
Subject: RV-List: Prop cable throw vs governor throw
Folks,
I'm in the final reassembly stages after a derecho/tornado blew the hangar
door in to my prop..prop is rebuilt and engine tore down for inspection.
I have found while verifying my cabling that the prop governor has 1/8" more
throw than my cable. I have it set up so the fine stop matches up but it
won't go all the way coarse.
I'm kinda thinking it doesn't matter as I don't think I have ever had the
prop that far coarse. I can get a custom made cable with the correct throw
- but do I need to?
RV6A
IO360B1F6 LASAR/Injected
MTV12(B) 183-59 hydraulic CS
I'll be sending this to the MT folks as well for their input.
Ralph Capen
www.aeroelectric.com
www.buildersbooks.com
www.homebuilthelp.com
http://www.matronics.com/contribution
http://www.matronics.com/Navigator?RV-List
http://forums.matronics.com
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Looking for someone to work on my RV-6 |
William Dean Family,
Sorry for you loss. Go to www.matronics.com/subscribe/ and follow the prompt.
Harry Crosby
----- Original Message -----
From: "William Dean" <billoves2fly@yahoo.com>
Sent: Sunday, November 18, 2012 3:58:23 AM
Subject: Re: RV-List: Looking for someone to work on my RV-6
We have gone to Yahoo groups and removed all the groups, how do we get off this
group. My father passed away and we no longer need these emails. Thank you for
any assistance you can provide.
The Dean family
Sent from my iPad
On Nov 17, 2012, at 5:16 PM, N616TB <N616TB@btsapps.com> wrote:
>
> I have a flying RV-6 with over 150 hours. I had an incident landing in grass
where a wheel pant came apart and rotated into the fuel tank. We were able to
patch the tank however, I would like to have a new tank built. I have all the
new parts for a completely new tank. I am looking for someone in Texas who could
do this work as I am in process of moving my shop. I can bring the airplane
to your location.
> Please contact me off list. N616tb at btsapps dot com
>
> Best Regards;
>
> Timothy Bryan
> We are what we repeatedly do. Excellence, therefore, is not an act but a habit.
> Aristotle
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|