Today's Message Index:
----------------------
1. 03:02 PM - RVx-List vs. RV-List Subscriptions (Matt Dralle)
2. 03:53 PM - RV-10 (Gary B. Jacobs)
3. 04:19 PM - Re: RV-10 (Dennis and Stephanie Smith)
4. 09:51 PM - RV-10 (Scott Schmidt)
5. 10:16 PM - Re: RV-10 (Dan Checkoway)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
rv7-list@matronics.com, rv8-list@matronics.com, rv9-list@matronics.com,
rv10-list@matronics.com, rvcanada-list@matronics.com,
rveurope-list@matronics.com
| Subject: | RVx-List vs. RV-List Subscriptions |
--> RV10-List message posted by: Matt Dralle <dralle@matronics.com>
Dear RV-x Listers,
I was chatting with a nice fellow on the new Matronics RV6-List Chatroom
yesterday ( http://www.matronics.com/chat ), and he ask me an interesting
question. Basically, what he was saying was that he had been subscribed to
the RV-List back a few years ago and he used to get a lot of messages each
day. Recently, he resubscribed and now only gets a few messages. "What
Happened?", he wanted to know...
Long story short, originally he had subscribed to the non-model specific
List, the "RV-List@matronics.com". When he resubscribed, he just
subscribed to the model-specific List, the "RV6-List@matronics.com". Since
the model-specific Lists receive far less traffic than the main RV-List,
the mystery of his reduced content was solved. He's now subscribed to the
Main RV-List in addition to the RV6-List and is happily receiving a few
more messages each day.
I realize that many of you have made a conscious decision to only subscribe
to one or more of the model-specific Lists. This conversation did make me
wonder, though, just how many people have subscribed to the model-specific
Lists, not knowing that a lot of the RV dialog is really on the main
RV-List...?
Anyway, I thought I'd post a little message today and spread the word. I
did some number crunching on the RVx-Lists vs. RV-List subscriptions and
found that there are 819 unique people subscribed to one or more
model-specific RVx-Lists but that are NOT subscribed to the general
RV-List! That's a lot of people missing out on a main flow of RV information.
I've setup a little web page where you can check to see if you're currently
subscribed to the RV-List and easily subscribe if you're not!
http://www.matronics.com/rv-list/Am-I-Subscribed.html
The RV-List is where all the action is! Subscribe today! :-)
Best regards,
Matt Dralle
Email List Admin.
Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551
925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email
http://www.matronics.com/ WWW | Featuring Products For Aircraft
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "Gary B. Jacobs" <gblayne@mchsi.com>
Have finished my vertical stab, rudder & horizontal stab. Starting on the elevator.
So far this kit is awesome. The experience Van's Aircraft gained from
doing all those other kits really shows on this one. I have a band saw and pneumatic
rivet squeezer and couldn't imagine doing this without it.
Gary & Marianne Jacobs
535 Woodbine Ct.
Mason City, IA 50401
gblayne@mchsi.com
(641) 420-8815
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "Dennis and Stephanie Smith" <famflier@centurytel.net>
Gary
I just got my empennage kit last week, so I am a few weeks behind you.
Hopefully I will catch up someday.
I was wondering which pneumatic squeezer you were using and on which parts?
Might be something I should get as well.
Keep up the good work.
Dennis
RV-10 #97
-------Original Message-------
From: rv10-list@matronics.com
Subject: RV10-List: RV-10
--> RV10-List message posted by: "Gary B. Jacobs" <gblayne@mchsi.com>
Have finished my vertical stab, rudder & horizontal stab. Starting on the
elevator. So far this kit is awesome. The experience Van's Aircraft gained
from doing all those other kits really shows on this one. I have a band saw
and pneumatic rivet squeezer and couldn't imagine doing this without it.
Gary & Marianne Jacobs
535 Woodbine Ct.
Mason City, IA 50401
gblayne@mchsi.com
(641) 420-8815
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "Scott Schmidt" <sschmidt@USSynthetic.com>
Our kit shows up tomorrow afternoon. I can hardly wait to get started.
I've spend the last two months preparing the garage and building a paint
booth in my basement. For my wife I installed a TV / DVD combo in the
garage and then plumbed my air up from my basement and put the compressor
down there so I didn't have any noise in the garage. I then put a switch
both in the garage and in the basement to turn the compressor on and off. I
will get a website up in a few weeks and post some pictures. The paint
booth turned out great. I live in Salt Lake so I knew I couldn't paint
outside in the winter.
Here are a couple of questions I need answered.
What pressure are you running on your rivet guns? I have a 3X
Scott Schmidt
USSynthetic Product Manager
1260 South 1600 West
Orem UT 84058
Phone: 801-235-9001
Fax: 801-235-9141
Cell: 801-319-3094
sschmidt@ussynthetic.com
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Dennis and
Stephanie Smith
Subject: Re: RV10-List: RV-10
--> RV10-List message posted by: "Dennis and Stephanie Smith"
<famflier@centurytel.net>
Gary
I just got my empennage kit last week, so I am a few weeks behind you.
Hopefully I will catch up someday.
I was wondering which pneumatic squeezer you were using and on which parts?
Might be something I should get as well.
Keep up the good work.
Dennis
RV-10 #97
-------Original Message-------
From: rv10-list@matronics.com
Subject: RV10-List: RV-10
--> RV10-List message posted by: "Gary B. Jacobs" <gblayne@mchsi.com>
Have finished my vertical stab, rudder & horizontal stab. Starting on the
elevator. So far this kit is awesome. The experience Van's Aircraft gained
from doing all those other kits really shows on this one. I have a band saw
and pneumatic rivet squeezer and couldn't imagine doing this without it.
Gary & Marianne Jacobs
535 Woodbine Ct.
Mason City, IA 50401
gblayne@mchsi.com
(641) 420-8815
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "Dan Checkoway" <dan@rvproject.com>
> Here are a couple of questions I need answered.
> What pressure are you running on your rivet guns? I have a 3X
http://www.rvproject.com/rivets.html
At the bottom of the page, there are a couple of charts I threw together
with "ballpark" air pressures for various rivet sizes. Take it with a grain
of salt...my experience is that every setup is slightly different.
)_( Dan
RV-7 N714D
http://www.rvproject.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|