Today's Message Index:
----------------------
1. 10:47 AM - Re: Gear elastomers (Randy DeBauw)
2. 06:40 PM - -10 POH (Sean Stephens)
3. 07:32 PM - Strobe wiring (John Hasbrouck)
4. 08:10 PM - Re: Strobe wiring (Tim Olson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "Randy DeBauw" <Randy@abros.com>
What I used was some 1" ratchet straps off of the engine mount. 2
worked but a third would even be better. Randy
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Rob Kermanj
Subject: RV10-List: Gear elastomers
--> RV10-List message posted by: Rob Kermanj <rv10es@earthlink.net>
Can anyone tell me how you installed the nose gear rubber donuts? I am
having a heck of the time squeezing them to install the top bolt. I
even use a clamp and some wood blocking but cannot squeeze them enough
before the clamp bend and wants to give.
I am using one aluminum washer under the top collar. This part is not
identified but is the only part that fits under it.
Thanks. Ro.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: Sean Stephens <schmoboy@cox.net>
I ran across a great POH for a -6A here...
<http://rv.supermatrix.com/frame1-docs.html>
Any of the flying -10s have a good POH example yet?
-Sean #40303
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV10-List message posted by: "John Hasbrouck" <jhasbrouck@woh.rr.com>
I'm working on the wing wiring. Assuming I place the strobe power supply in
the tailcone near the battery, how long of a wire run should I plan on for
the wing tip strobes? I'm using Whelen strobes with shielded cable, any
problems running that with the rest of the power supply wires through
conduit in the wings? Coax for nav antenna will be run seperately.
John Hasbrouck
#40264
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Strobe wiring |
--> RV10-List message posted by: Tim Olson <Tim@MyRV10.com>
That's exactly where I'm mounting my strobe pack and I'm trying to
slightly overestimate the wire length calling it 20'.
I think you can run the strobes with shielded cable with the rest of
the power wires just fine. I haven't run mine yet, but it will
more depend on what will fit in the conduit than anything else.
I plan to run my Nav antenna separately too.
Tim Olson -- RV-10 #40170
DO NOT ARCHIVE
John Hasbrouck wrote:
> --> RV10-List message posted by: "John Hasbrouck" <jhasbrouck@woh.rr.com>
>
> I'm working on the wing wiring. Assuming I place the strobe power
> supply in the tailcone near the battery, how long of a wire run should I
> plan on for the wing tip strobes? I'm using Whelen strobes with
> shielded cable, any problems running that with the rest of the power
> supply wires through conduit in the wings? Coax for nav antenna will be
> run seperately.
>
> John Hasbrouck
> #40264
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|