----------------------------------------------------------
                           RV10-List Digest Archive
                                      ---
                     Total Messages Posted Wed 09/14/05: 4
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 10:47 AM - Re: Gear elastomers  (Randy DeBauw)
     2. 06:40 PM - -10 POH  (Sean Stephens)
     3. 07:32 PM - Strobe wiring  (John Hasbrouck)
     4. 08:10 PM - Re: Strobe wiring  (Tim Olson)
 
 
 
________________________________  Message 1  _____________________________________


Time: 10:47:44 AM PST US
Subject: RE: RV10-List: Gear elastomers
From: "Randy DeBauw" <Randy@abros.com>

--> RV10-List message posted by: "Randy DeBauw" <Randy@abros.com>

What I used was some 1" ratchet straps off of the engine mount.  2
worked but a third would even be better.  Randy

-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Rob Kermanj
Subject: RV10-List: Gear elastomers

--> RV10-List message posted by: Rob Kermanj <rv10es@earthlink.net>

Can anyone tell me how you installed the nose gear rubber donuts?  I am 
having a heck of the time squeezing them to install the top bolt.  I 
even use a clamp and some wood blocking but cannot squeeze them enough 
before the clamp bend and wants to give.

I am using one aluminum washer under the top collar.  This part is not 
identified but is the only part that fits under it.

Thanks.  Ro.


________________________________  Message 2  _____________________________________


Time: 06:40:59 PM PST US
From: Sean Stephens <schmoboy@cox.net>
Subject: RV10-List: -10 POH

--> RV10-List message posted by: Sean Stephens <schmoboy@cox.net>

I ran across a great POH for a -6A here...

<http://rv.supermatrix.com/frame1-docs.html>

Any of the flying -10s have a good POH example yet?

-Sean #40303


________________________________  Message 3  _____________________________________


Time: 07:32:23 PM PST US
From: "John Hasbrouck" <jhasbrouck@woh.rr.com>
Subject: RV10-List: Strobe wiring

--> RV10-List message posted by: "John Hasbrouck" <jhasbrouck@woh.rr.com>

I'm working on the wing wiring.  Assuming I place the strobe power supply in 
the tailcone near the battery, how long of a wire run should I plan on for 
the wing tip strobes?  I'm using Whelen strobes with shielded cable, any 
problems running that with the rest of the power supply wires through 
conduit in the wings?  Coax for nav antenna will be run seperately.

John Hasbrouck
#40264 


________________________________  Message 4  _____________________________________


Time: 08:10:26 PM PST US
From: Tim Olson <Tim@MyRV10.com>
Subject: Re: RV10-List: Strobe wiring

--> RV10-List message posted by: Tim Olson <Tim@MyRV10.com>

That's exactly where I'm mounting my strobe pack and I'm trying to 
slightly overestimate the wire length calling it 20'.

I think you can run the strobes with shielded cable with the rest of
the power wires just fine.  I haven't run mine yet, but it will
more depend on what will fit in the conduit than anything else.
I plan to run my Nav antenna separately too.


Tim Olson -- RV-10  #40170
DO NOT ARCHIVE


John Hasbrouck wrote:
> --> RV10-List message posted by: "John Hasbrouck" <jhasbrouck@woh.rr.com>
> 
> I'm working on the wing wiring.  Assuming I place the strobe power 
> supply in the tailcone near the battery, how long of a wire run should I 
> plan on for the wing tip strobes?  I'm using Whelen strobes with 
> shielded cable, any problems running that with the rest of the power 
> supply wires through conduit in the wings?  Coax for nav antenna will be 
> run seperately.
> 
> John Hasbrouck
> #40264
> 
>