---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Thu 08/31/06: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:08 AM - Re: Re: LOE Flyin (Mark Ritter) 2. 03:58 AM - Re: Avionics coolingAvionics cooling (Wayne Edgerton) 3. 04:44 AM - Re: Avionics coolingAvionics cooling (Marcus Cooper) 4. 05:04 AM - Re: gretz (Scott Lewis) 5. 05:33 AM - Re: Re: LOE Flyin (Russell Daves) 6. 04:06 PM - Re: gretz (Rob Wright) ________________________________ Message 1 _____________________________________ Time: 03:08:03 AM PST US From: "Mark Ritter" Subject: RE: RV10-List: Re: LOE Flyin --> RV10-List message posted by: "Mark Ritter" Russ - Why couldn't you just lie to me and tell me the fairings are a piece of cake? Between you and Tim I'm not looking forward to finishing them. Looking forward to seeing your plane after the paint job. I hear nothing but good things about the work Grady does at GLO. I have a Nov. 20 date to take my plane to Allen in Brady for painting - assuming I have the fairings finished by then. LOE should have a great turnout of RV's. Hope to see you there. Mark Do not archive >From: "Russell Daves" >To: >Subject: RV10-List: Re: LOE Flyin >Date: Wed, 30 Aug 2006 22:11:06 -0500 > >--> RV10-List message posted by: "Russell Daves" > >You have your work cut out for you, the gear leg fairings and wheel pants >are a lot of work. I spent two full weeks of hard hours doing mine. I >wished I had done them before I put on my wings. They would have been a >lot easier. > >Hope to see you at LOE 2006 along with the rest of the Texas crowd. I will >be showing off N710RV newly painted. > >Russ Daves > >>>Starting wheel and gear leg fairings tomorrow. Pray for me. Hope to >>>finish in time to make it to LOE flyin. Are you going? >>> >>>Mark >>> >>>Do not archive >>> >> >> >> >> >> > > ________________________________ Message 2 _____________________________________ Time: 03:58:59 AM PST US From: "Wayne Edgerton" Subject: Re: RV10-List: Avionics coolingAvionics cooling I'm having Stein install avionics cooling fans for my panel but I also have put in a couple of computer fans in the glare shield for defrosting but I think this will also allow for some of the heat coming from the avionics to vent through these holes. I've attached a photo of the holes in my glare shield. The picture was before I installed the fans. I think these holes will also help with the cooling process. Wayne Edgerton #40336 ________________________________ Message 3 _____________________________________ Time: 04:44:24 AM PST US From: "Marcus Cooper" Subject: RE: RV10-List: Avionics coolingAvionics cooling Wayne, The glare shield looks great, very nice work. I wish I had prepped mine better prior to putting on the windscreen. I got a little too exited about making progress and it definitely made life tougher. Marcus Do not archive _____ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Wayne Edgerton Sent: Thursday, August 31, 2006 6:58 AM Subject: Re: RV10-List: Avionics coolingAvionics cooling I'm having Stein install avionics cooling fans for my panel but I also have put in a couple of computer fans in the glare shield for defrosting but I think this will also allow for some of the heat coming from the avionics to vent through these holes. I've attached a photo of the holes in my glare shield. The picture was before I installed the fans. I think these holes will also help with the cooling process. Wayne Edgerton #40336 ________________________________ Message 4 _____________________________________ Time: 05:04:50 AM PST US From: Scott Lewis Subject: Re: RV10-List: gretz --> RV10-List message posted by: Scott Lewis G'day Rob, Rob Wright wrote: > Wondering if anyone has pictures of how you plumbed your gretz pitot > tube. Specifically, did you bend your copper tubing or connect your > other line to it with a bend or with an elbow fitting? Im also using > the SafeAir tubing so any help on that would be great too. I have the exact setup, haven't installed yet though. I am planning an AN822-4D fitting (Elbow with one pipe thread end) on the end of the Gretz tube which then connects directly to the Safeair tubing. Have fun, Scott Lewis RV-10 40172 Adelaide, South Australia ________________________________ Message 5 _____________________________________ Time: 05:33:54 AM PST US From: "Russell Daves" Subject: Re: RV10-List: Re: LOE Flyin --> RV10-List message posted by: "Russell Daves" Lord willing and the creek doesn't rise I will for sure be at LOE. Can't wait to see you baby as well and compare build stores. Russ ----- Original Message ----- From: "Mark Ritter" Sent: Thursday, August 31, 2006 5:06 AM Subject: RE: RV10-List: Re: LOE Flyin > --> RV10-List message posted by: "Mark Ritter" > > Russ - Why couldn't you just lie to me and tell me the fairings are a > piece of cake? Between you and Tim I'm not looking forward to finishing > them. Looking forward to seeing your plane after the paint job. I hear > nothing but good things about the work Grady does at GLO. I have a Nov. 20 > date to take my plane to Allen in Brady for painting - assuming I have > the fairings finished by then. > > LOE should have a great turnout of RV's. Hope to see you there. > > Mark > Do not archive > > >>From: "Russell Daves" >>To: >>Subject: RV10-List: Re: LOE Flyin >>Date: Wed, 30 Aug 2006 22:11:06 -0500 >> >>--> RV10-List message posted by: "Russell Daves" >> >>You have your work cut out for you, the gear leg fairings and wheel pants >>are a lot of work. I spent two full weeks of hard hours doing mine. I >>wished I had done them before I put on my wings. They would have been a >>lot easier. >> >>Hope to see you at LOE 2006 along with the rest of the Texas crowd. I >>will be showing off N710RV newly painted. >> >>Russ Daves >> >>>>Starting wheel and gear leg fairings tomorrow. Pray for me. Hope to >>>>finish in time to make it to LOE flyin. Are you going? >>>> >>>>Mark >>>> >>>>Do not archive >>>> >>> >>> >>> >>> >>> >> >> >> >> >> >> > > > ________________________________ Message 6 _____________________________________ Time: 04:06:28 PM PST US From: "Rob Wright" Subject: RE: RV10-List: gretz --> RV10-List message posted by: "Rob Wright" Yeah, thanks. I went with that idea and just got my fitting, nut, and sleeve in today from AS&S. Time to forge ahead with this so I can get the skins fully riveted on. Rob Wright #392 Bottom Wing Skins -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Scott Lewis Sent: Thursday, August 31, 2006 7:05 AM Subject: Re: RV10-List: gretz --> RV10-List message posted by: Scott Lewis G'day Rob, Rob Wright wrote: > Wondering if anyone has pictures of how you plumbed your gretz pitot > tube. Specifically, did you bend your copper tubing or connect your > other line to it with a bend or with an elbow fitting? I'm also using > the SafeAir tubing so any help on that would be great too. I have the exact setup, haven't installed yet though. I am planning an AN822-4D fitting (Elbow with one pipe thread end) on the end of the Gretz tube which then connects directly to the Safeair tubing. Have fun, Scott Lewis RV-10 40172 Adelaide, South Australia