---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sat 07/07/07: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:02 AM - Re: Final Trimming of the Wingtip Lenses (Michael Wellenzohn) 2. 11:04 AM - Tail cone question (Stephen Blank) 3. 01:17 PM - Re: Tail cone question (Bob Leffler) 4. 02:38 PM - Dynon OAT Probe (Albert Gardner) 5. 02:40 PM - Nose gear question (Wayne Edgerton) 6. 03:48 PM - Re: Tail cone question (Jim Beyer) 7. 04:02 PM - Re: Tail cone question (Vernon Smith) 8. 04:15 PM - Re: Nose gear question (Bruce Snyder) 9. 04:42 PM - Re: Nose gear question (Rick) ________________________________ Message 1 _____________________________________ Time: 03:02:20 AM PST US Subject: RV10-List: Re: Final Trimming of the Wingtip Lenses From: "Michael Wellenzohn" I used a vixen file for the final work. Michael #40511 -------- RV-10 builder (wings) #511 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=122607#122607 ________________________________ Message 2 _____________________________________ Time: 11:04:47 AM PST US From: "Stephen Blank" Subject: RV10-List: Tail cone question On page 10-4, I just trimmed the F1010A angle support to fit the F1010 bulkhead. It does not fit between the tabs at the top of the F1010 bulkhead when positioned 1/8 above as in the figure? It is way off, i keep measuring, all dimensions appear corrrect. Has anyone else noticed this? I plan to just trim more (about 0.25" off the angled portion until it seats passively. The other option would be to fasten it to the aft side with NO tirmming? Will that mess other things up? Thanks for any input. - Steve RV-10 #40499 -- Stephen G. Blank, DDS 184 NW Central Park Plaza Port St. Lucie, FL 34986 772-475-5556 >>> Cell ________________________________ Message 3 _____________________________________ Time: 01:17:34 PM PST US From: "Bob Leffler" Subject: RE: RV10-List: Tail cone question Please keep us informed as to what you find. I'm a little behind you in construction. I probably won't get to this until mid August based on vacation schedule and the abundance of "honey do" items. :^( From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Stephen Blank Sent: Saturday, July 07, 2007 2:02 PM Subject: RV10-List: Tail cone question On page 10-4, I just trimmed the F1010A angle support to fit the F1010 bulkhead. It does not fit between the tabs at the top of the F1010 bulkhead when positioned 1/8 above as in the figure? It is way off, i keep measuring, all dimensions appear corrrect. Has anyone else noticed this? I plan to just trim more (about 0.25" off the angled portion until it seats passively. The other option would be to fasten it to the aft side with NO tirmming? Will that mess other things up? Thanks for any input. - Steve RV-10 #40499 -- Stephen G. Blank, DDS 184 NW Central Park Plaza Port St. Lucie, FL 34986 772-475-5556 >>> Cell __________ NOD32 2383 (20070706) Information __________ ________________________________ Message 4 _____________________________________ Time: 02:38:40 PM PST US From: "Albert Gardner" Subject: RV10-List: Dynon OAT Probe My Dynon 180 always shows -45F or -46F degrees AOT. I ordered another OAT probe but it reads the same. This is the OAT probe with the black band that connects into the remote compass box. Can't find anything wrong with the wiring and the probe is configured as choice 2 in the setup menu just like Dynon says. Anyone else been down this road? Albert Gardner Yuma, AZ ________________________________ Message 5 _____________________________________ Time: 02:40:23 PM PST US From: "Wayne Edgerton" Subject: RV10-List: Nose gear question If someone has the nose gear leg assembly but don't yet have it mounted I was wondering if you could take a look and tell me how many thread there are on the spindle at the end of the assembly that the nose wheel tire attaches to. Also whether there is a cotter pin hole in the threads. Wayne Edgerton #40336 do not archive ________________________________ Message 6 _____________________________________ Time: 03:48:03 PM PST US From: "Jim Beyer" Subject: Re: RV10-List: Tail cone question Stephen, I'll start out by saying I think I built the F-1010A wrong the first time as I ground the angle the wrong way. The area that is removed includes a triangular section of one of the sides of the angle, as well as all of the other side of the angle. See if this makes sense, when F-1010A is oriented correctly, the horizontal piece of the angle will measure 10-3/4" at the forward edge reducing down to 10-7/16 (10-3/4 minus 5/32 minus another 5/32) at the aft edge. The aft edge is also where the vertical piece of the angle is joined with the horizontal piece. The vertical piece of the angle (and the part that gets matched drilled with F-1010) will measure 10-7/16 x 1" in a straight 90* rectangle. You will definitely want to make this part correct as all four of four bolts that hold the forward part of the horizontal stabilizer to the fuselage go through F-1010A. Too small will likely lead into edge distance problems down the road. Take a peek at page 10-10 figure 3 so see how the angle is required to fit in between the fuselage stringers (F1032L/R) and that F-1010B then sits on top of F1010A so that later down the road six bolts will hold all of this together and keep the horizontal stabilizer firmly attached. I hope this helps. -Jim 40603 On 7/7/07, Stephen Blank wrote: > > On page 10-4, I just trimmed the F1010A angle support to fit the F1010 > bulkhead. It does not fit between the tabs at the top of the F1010 bulkhead > when positioned 1/8 above as in the figure? It is way off, i keep measuring, > all dimensions appear corrrect. Has anyone else noticed this? I plan to > just trim more (about 0.25" off the angled portion until it seats > passively. The other option would be to fasten it to the aft side with NO > tirmming? Will that mess other things up? Thanks for any input. - Steve > > > RV-10 #40499 > -- > Stephen G. Blank, DDS > 184 NW Central Park Plaza > Port St. Lucie, FL 34986 > > 772-475-5556 >>> Cell > > * > > > * > > -- o=\o ________________________________ Message 7 _____________________________________ Time: 04:02:48 PM PST US From: Vernon Smith Subject: RE: RV10-List: Tail cone question Stephen, In step 1 on page 10-4 it calls for an angle to be cut in each end of F1010 A. Double check the top drawing on step one; this may be the cause. As far as mounting it on the aft side, look forward to page 10-10 and you can see how it fits the tailcone. Vern Smith (#324 fuselage) matronics.comSubject: RV10-List: Tail cone question On page 10-4, I just trimmed the F1010A angle support to fit the F1010 bul khead. It does not fit between the tabs at the top of the F1010 bulkhead wh en positioned 1/8 above as in the figure? It is way off, i keep measuring, all dimensions appear corrrect. Has anyone else noticed this? I plan to ju st trim more (about 0.25" off the angled portion until it seats passively. The other option would be to fasten it to the aft side with NO tirmming? W ill that mess other things up? Thanks for any input. - Steve RV-10 #40499 --Stephen G. Blank, DDS184 NW Central Park PlazaPort St. Lucie, FL 3498677 2-475-5556 >>> Cell _________________________________________________________________ PC Magazine=92s 2007 editors=92 choice for best web mail=97award-winning Wi ndows Live Hotmail. ration_HMWL_mini_pcmag_0707 ________________________________ Message 8 _____________________________________ Time: 04:15:59 PM PST US From: "Bruce Snyder" Subject: RE: RV10-List: Nose gear question Wayne, I counted 15 threads and there is a hole in the threads for a cotter pin. Bruce Snyder #40353 _____ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Wayne Edgerton Sent: Saturday, July 07, 2007 5:36 PM Subject: RV10-List: Nose gear question If someone has the nose gear leg assembly but don't yet have it mounted I was wondering if you could take a look and tell me how many thread there are on the spindle at the end of the assembly that the nose wheel tire attaches to. Also whether there is a cotter pin hole in the threads. Wayne Edgerton #40336 do not archive ________________________________ Message 9 _____________________________________ Time: 04:42:37 PM PST US From: Rick Subject: Re: RV10-List: Nose gear question Wayne, Since your flying........you didn't lose your nose fork did you? Rick S. 40185 do not archive ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.