---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sat 07/14/07: 7 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:11 AM - Re: Re: Need someone to inspect my work (nicholscatoauto@aol.com) 2. 09:38 AM - Engine Mount in FL? (Jesse Saint) 3. 11:48 AM - Firewall Forward heads up (David McNeill) 4. 06:49 PM - Goo Gone? (Shawn Moon) 5. 07:03 PM - Re: Goo Gone? (linn Walters) 6. 07:05 PM - Re: Goo Gone? (GenGrumpy@aol.com) 7. 07:33 PM - Re: Need someone to inspect my work (orchidman) ________________________________ Message 1 _____________________________________ Time: 08:11:13 AM PST US Subject: Re: RV10-List: Re: Need someone to inspect my work From: nicholscatoauto@aol.com Gary, That is not a bad idea. I might be able to do that. Right now all the parts are together and I would like someone to look at it that way too before I take it back apart. Thanks Jeff -----Original Message----- From: orchidman Sent: Fri, 13 Jul 2007 11:27 am Subject: RV10-List: Re: Need someone to inspect my work Jeff, Just a thought and my 2 cents, Are you going to Osh? If you are driving in something like a SUV or mini-van, could you through in some of the smaller items like the rudder, elevator and HS into it and bring them to Osh. I am sure that you would have a flock of builders in the 10 HQ that would give you all the comments you would need. Also, it could be used as a show and tell for would-be builders. [Laughing] I have no comment (zero cents) for your tech advisor. -------- Gary Blankenbiller RV10 - # 40674 (N410GB reserved) do not archive Read this topic online here: http://forums.matronics.com/viewtopic.php?p=123616#123616 ________________________________________________________________________ ________________________________ Message 2 _____________________________________ Time: 09:38:50 AM PST US From: Jesse Saint Subject: RV10-List: Engine Mount in FL? Does anybody in Florida have an engine mount not yet installed? Please call if so. Do not archive Jesse Saint Saint Aviation, Inc jesse@saintaviation.com www.saintaviation.com 352-427-0285 Leather interior kit for the RV-10 - www.saintaviation.com/interior -----Original Message----- From: "RV Builder (Michael Sausen)" Sent: 7/13/2007 10:12 PM Subject: RE: RV10-List: Great Job Vic on your Angel Flight Any one that is interested needs to check with their regional Angel Flight office. Some of the regions allow experimental and others don't. Unfortunately the region that covers WI doesn't so I'm out. They are also usually at OSH for anyone interested in talking with them. Michael From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Marcus Cooper Sent: Friday, July 13, 2007 6:22 PM Subject: RE: RV10-List: Great Job Vic on your Angel Flight For what it's worth, before leaving Georgia I contacted Angel Flight and they said no problem as far as being experimental as long as it was IFR rated I have read that some organizations will limit you to organs and other support but not people in homebuilts, but hopefully things are improving. Marcus 40286 ________________________________ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Scott Schmidt Sent: Friday, July 13, 2007 2:06 PM Subject: RV10-List: Great Job Vic on your Angel Flight I don't know if many of you have heard this off of VansAirforce.net but you should. http://www.vansairforce.net/delete_eventually/_206202505907121313477704543502.WAV First of all, great job Vic. I'm sure patients have a blast flying in the RV-10. Was this an Angel Flight or something different? I have wanted to get involved in Angel Flight but as most of you know they do not allow Experimental aircraft to fly patients. I have been able to transport toys but not passengers. The last part of the message is a great one even though it is a Texas organization, if we can get these types organizations to allow instrument rated pilots in instrument rated RV's allowed, maybe Angel Flight will make an exception to their current rule. If you ever have a chance over the next couple weeks, please send an e-mail to angel flight encouraging the use of RV's. It always seemed funny that they allow 1960 172's but not brand new RV's. The RV had a great safety record and social organization plus most RV pilots love to fly their planes and are very willing to help other people out. Here is the main angel flight e-mail and you also may want to contact your regional office as well. angel@angelflight.com Keep up the great work Vic. Scott Schmidt scottmschmidt@yahoo.com ________________________________ Message 3 _____________________________________ Time: 11:48:13 AM PST US From: "David McNeill" Subject: RV10-List: Firewall Forward heads up If you are using the IO540 and the quadrant, be advised to adjust the cables at the throttle quadrant end for maximum length. Also note that when using the inverted V pattern through the firewall you will be crossing the throttle and mixture cables as the throttle is right side and the mixture is left side forward of the firewall. This works to effectively shorten the cables. It appears that in my case the cables can be effectively lengthened by about 1 inch but will require about 2 extra hours of labor to remove them enough to work on the length. ________________________________ Message 4 _____________________________________ Time: 06:49:05 PM PST US From: Shawn Moon Subject: RV10-List: Goo Gone? I need to remove tape residue from my wing spar. I was thinking of using Goo Gone to do it but wanted to know if anybody knows of any ill effects from doing this. Any issues? Is there something that would be more appropriate to use? Thanks. --Shawn 40366 - Wings Need a vacation? Get great deals to amazing places on Yahoo! Travel. http://travel.yahoo.com/ ________________________________ Message 5 _____________________________________ Time: 07:03:52 PM PST US From: linn Walters Subject: Re: RV10-List: Goo Gone? Kerosene works on most all tape and tape glue. Wet a rag and place on the tape to let it soak in. Linn Shawn Moon wrote: > I need to remove tape residue from my wing spar. I was thinking of > using Goo Gone to do it but wanted to know if anybody knows of any ill > effects from doing this. Any issues? Is there something that would > be more appropriate to use? Thanks. > > --Shawn > 40366 - Wings > > > ------------------------------------------------------------------------ > Fussy? Opinionated? Impossible to please? Perfect. Join Yahoo!'s user > panel > > and lay it on us. > > ________________________________ Message 6 _____________________________________ Time: 07:05:11 PM PST US From: GenGrumpy@aol.com Subject: Re: RV10-List: Goo Gone? Haven't tried goo gone on aluminum, but Acetone works pretty good also. grumpy do not archive In a message dated 7/14/2007 8:50:14 PM Central Standard Time, moons1999@yahoo.com writes: I need to remove tape residue from my wing spar. I was thinking of using Goo Gone to do it but wanted to know if anybody knows of any ill effects from doing this. Any issues? Is there something that would be more appropriate to use? Thanks. ************************************** Get a sneak peak of the all-new AOL at http://discover.aol.com/memed/aolcom30tour ________________________________ Message 7 _____________________________________ Time: 07:33:52 PM PST US Subject: RV10-List: Re: Need someone to inspect my work From: "orchidman" nicholscatoauto(at)aol.co wrote: > Gary, > That is not a bad idea. I might be able to do that. Right now all the parts are together and I would like someone to look at it that way too before I take it back apart. > Thanks > Jeff-- Having a tech advisor look things over is very important for many reasons already noted by others but in the interim a couple example pieces looked over by others at Osh would probably go a long way to calming your anxiety. I had 2 tech advisors in my local area come by and go over my emp and wings just after I put the top skins on. I had several rivets that I was not sure about and I asked them, "In this area, is there any problems with any of the rivets." "No" and they kept looking to see if they could find a rivet that needed replacing. I slept very well that night as they were very happy with my work to that point. -------- Gary Blankenbiller RV10 - # 40674 (N410GB reserved) do not archive Read this topic online here: http://forums.matronics.com/viewtopic.php?p=123852#123852 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.