Today's Message Index:
----------------------
1. 07:29 AM - Re: RV10 Door seals (Rob Kermanj)
2. 08:03 AM - Rosen Visors (Jesse Saint)
3. 09:13 AM - Re: Rosen Visors (RV Builder (Michael Sausen))
4. 01:27 PM - Re: Rosen Visors (John Dunne)
5. 01:31 PM - Re: Rosen Visors (John Dunne)
6. 01:47 PM - Re: Rosen Visors (Robin Marks)
7. 03:32 PM - Re: Rosen Visors (John Dunne)
8. 07:40 PM - Another one begins #40761 (n277dl)
9. 08:07 PM - Re: Another one begins #40761 (John W. Cox)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV10 Door seals |
Kevin, I have not noticed an appreciable amount of compression in the
door seals. I would sand the gutter to get a better fit. Be careful
though, you need to be able to get a good seal. Another possibility
is to fill the cabin top to match the door edge or combination of
both. Whatever you decide, do it now because it does fit any better
on it's own.
My door fits a whole lot better with this seal than the supplied seal
with the kit but it is not perfect.
Rob
do not archive
On Sep 5, 2007, at 11:26 PM, John Testement wrote:
> <jwt@roadmapscoaching.com>
>
> Rob,
>
> Once you put the seal in, how much adjustment did you have to make
> to the
> channels to get the doors to close. I had a perfect door fit and
> when I put
> the seal on (from Brown) the door stood out about 1/4 inch (others
> told me
> I'd have this problem). I want to know if the seal will compress
> and the
> doors fit after some time, or if I should sand out the channels
> some to get
> the doors to sit flush. What have others done?
>
> John Testement
> jwt@roadmapscoaching.com
> 40321
> Richmond, VA
> Paint prep, interior, and LOTS of little stuff
> do not archive
>
>
> -----Original Message-----
> From: owner-rv10-list-server@matronics.com
> [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Rob Kermanj
> Sent: Sunday, June 10, 2007 7:19 AM
> To: rv10-list@matronics.com
> Subject: Re: RV10-List: RV10 Doors Video
>
>
> Kevin, I used Bulb seal, Item BA-1900010 from Brown Aircraft
> Supply in
> Jacksonville, FL. 904-396-6655. The only thing I don't like about
> it is
> that it leaves a black mark that I clean once in a while. However,
> the
> doors operate nicely and they are sealed. You also need Rubber and
> Gasket
> Adhesive by 3M, part 1300L to attach this thing.
>
> You may want to get their one page catalog and make your own
> determination.
> I think that they only sell door seals.
>
> Rob.
>
> 10:36 PM
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
For those who didn't get in on the group buy for Rosen Visors, I have a few
extra here. Contact me off the list if you are interested.
Do not archive.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Also, there is the visors that Alex is selling for considerably less than t
he Rosens.
http://www.aviationtechproducts.com/html/new_products.html
From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@m
atronics.com] On Behalf Of Jesse Saint
Sent: Thursday, September 06, 2007 10:00 AM
Subject: RV10-List: Rosen Visors
For those who didn't get in on the group buy for Rosen Visors, I have a few
extra here. Contact me off the list if you are interested.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com<mailto:jesse@saintaviation.com>
www.saintaviation.com<http://www.saintaviation.com>
Cell: 352-427-0285
Fax: 815-377-3694
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Rosen Visors |
Hi Jesse,
I would like a set of visors.
Let me know how much and how to pay you and I can give you my Fedex
account for freight forwarding to me.
Do you use Paypal?
Best regards,
John 40315 Australia.
----- Original Message -----
From: Jesse Saint
To: rv10-list@matronics.com
Sent: Friday, September 07, 2007 12:59 AM
Subject: RV10-List: Rosen Visors
For those who didn't get in on the group buy for Rosen Visors, I have
a few extra here. Contact me off the list if you are interested.
Do not archive.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Rosen Visors |
My apologies to the list.....should have directed to Jesse
John 40315
----- Original Message -----
From: John Dunne
To: rv10-list@matronics.com
Sent: Friday, September 07, 2007 6:26 AM
Subject: Re: RV10-List: Rosen Visors
Hi Jesse,
I would like a set of visors.
Let me know how much and how to pay you and I can give you my Fedex
account for freight forwarding to me.
Do you use Paypal?
Best regards,
John 40315 Australia.
----- Original Message -----
From: Jesse Saint
To: rv10-list@matronics.com
Sent: Friday, September 07, 2007 12:59 AM
Subject: RV10-List: Rosen Visors
For those who didn't get in on the group buy for Rosen Visors, I
have a few extra here. Contact me off the list if you are interested.
Do not archive.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
John, you can make it up to us by sharing your FedEx number with the
list.
Thanks in advance,
Robin J
Do Not Archive
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of John Dunne
Sent: Thursday, September 06, 2007 1:30 PM
Subject: Re: RV10-List: Rosen Visors
My apologies to the list.....should have directed to Jesse
John 40315
----- Original Message -----
From: John Dunne <mailto:acs@acspropeller.com.au>
To: rv10-list@matronics.com
Sent: Friday, September 07, 2007 6:26 AM
Subject: Re: RV10-List: Rosen Visors
Hi Jesse,
I would like a set of visors.
Let me know how much and how to pay you and I can give you my
Fedex account for freight forwarding to me.
Do you use Paypal?
Best regards,
John 40315 Australia.
----- Original Message -----
From: Jesse Saint <mailto:jesse@saintaviation.com>
To: rv10-list@matronics.com
Sent: Friday, September 07, 2007 12:59 AM
Subject: RV10-List: Rosen Visors
For those who didn't get in on the group buy for Rosen
Visors, I have a few extra here. Contact me off the list if you are
interested.
Do not archive.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s
.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s
.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Robin, I can do better than that..
If anyone on the list would like something from Australia we can send it
back with Airforce One.
Shouldn't be too hard.
John 40315
Do not archive
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Robin Marks
Sent: Friday, 7 September 2007 6:46 AM
Subject: RE: RV10-List: Rosen Visors
John, you can make it up to us by sharing your FedEx number with the list.
Thanks in advance,
Robin :-)
Do Not Archive
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of John Dunne
Sent: Thursday, September 06, 2007 1:30 PM
Subject: Re: RV10-List: Rosen Visors
My apologies to the list.....should have directed to Jesse
John 40315
----- Original Message -----
From: John <mailto:acs@acspropeller.com.au> Dunne
Sent: Friday, September 07, 2007 6:26 AM
Subject: Re: RV10-List: Rosen Visors
Hi Jesse,
I would like a set of visors.
Let me know how much and how to pay you and I can give you my Fedex account
for freight forwarding to me.
Do you use Paypal?
Best regards,
John 40315 Australia.
----- Original Message -----
From: Jesse <mailto:jesse@saintaviation.com> Saint
Sent: Friday, September 07, 2007 12:59 AM
Subject: RV10-List: Rosen Visors
For those who didn't get in on the group buy for Rosen Visors, I have a few
extra here. Contact me off the list if you are interested.
Do not archive.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com
/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com
/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
http://www.matronics.com/Navigator?RV10-List
http://forums.matronics.com
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Another one begins #40761 |
Well guys & gals the building begins again for me. I built a 7A with first flight
in 2004. Have about 550 hrs on it but now it's time for a more roomy XC edition.
The tail kit arrived this afternoon so I've spent the last couple hours getting
the big pieces out and inventoried. Did slow build on the -7A but will probably
go QB on the -10.
I've met a few of you up at Boone as I'm located in Muscatine, IA. My son lives
in Boone so the plane ends up there frequently.
Interesting (at least for me) bit of useless information... the night I filled
out the order form for the 7A was the first time the four seat plane was discussed
on Vans web site. I called the next morning before faxing the order for
the 7A in and asked about the four seater but was told it would be a couple years
before it was in production. I couldn't wait that long to begin building
so we decided to build the two seater and if the four seater made it and lived
up to expecations and if we could complete the two seater we'd do it again.
It did, we did so here we go again.
Doug
www.oncloud7.com/rv7.htm
10 builder #40761
7A flyer 550hrs
--------
Doug
RV7A flying ~500hrs
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=133186#133186
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Another one begins #40761 |
Always great to have another in the pursuit. And a Repeat Offender to
boot.
John Cox
Do not Archive
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of n277dl
Sent: Thursday, September 06, 2007 7:40 PM
Subject: RV10-List: Another one begins #40761
Well guys & gals the building begins again for me. I built a 7A with
first flight in 2004. Have about 550 hrs on it but now it's time for a
more roomy XC edition.
The tail kit arrived this afternoon so I've spent the last couple hours
getting the big pieces out and inventoried. Did slow build on the -7A
but will probably go QB on the -10.
I've met a few of you up at Boone as I'm located in Muscatine, IA. My
son lives in Boone so the plane ends up there frequently.
Interesting (at least for me) bit of useless information... the night I
filled out the order form for the 7A was the first time the four seat
plane was discussed on Vans web site. I called the next morning before
faxing the order for the 7A in and asked about the four seater but was
told it would be a couple years before it was in production. I couldn't
wait that long to begin building so we decided to build the two seater
and if the four seater made it and lived up to expecations and if we
could complete the two seater we'd do it again.
It did, we did so here we go again.
Doug
www.oncloud7.com/rv7.htm
10 builder #40761
7A flyer 550hrs
--------
Doug
RV7A flying ~500hrs
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=133186#133186
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|