Today's Message Index:
----------------------
1. 04:29 AM - Re: For What It's Worth... (darnpilot@aol.com)
2. 08:53 AM - Re: For What It's Worth... (Jeff Carpenter)
3. 09:18 AM - Re: RV10s to Copperstate (John W. Cox)
4. 09:50 AM - Re: RV10s to Copperstate (David McNeill)
5. 10:07 AM - Re: For What It's Worth... (Jim Beyer)
6. 11:22 AM - Another 10 gets paint (Marcus Cooper)
7. 03:40 PM - Looking to buy a RV 10 (David C. Watterson)
8. 03:55 PM - Re: Looking to buy a RV 10 (RV Builder (Michael Sausen))
9. 04:05 PM - Re: Looking to buy a RV 10 (Rob Kermanj)
10. 04:05 PM - Re: Looking to buy a RV 10 (David C. Watterson)
11. 04:11 PM - Re: Looking to buy a RV 10 (David C. Watterson)
12. 05:47 PM - Re: Looking to buy a RV 10 (bcondrey)
13. 05:51 PM - WD-1002 / F1001B / F1040 Fuse channel rivet holes (Les Kearney)
14. 06:06 PM - Re: RV10s to Copperstate (Jesse Saint)
15. 06:31 PM - Re: Looking to buy a RV 10 (John W. Cox)
16. 07:35 PM - Re: Looking to buy a RV 10 (dougpflyrv@aol.com)
17. 07:57 PM - Re: Looking to buy a RV 10 (Tim Olson)
18. 09:15 PM - Steam Gauges (Jeff Carpenter)
19. 10:43 PM - Re: RV10s to Copperstate (Scott Schmidt)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: For What It's Worth... |
Anyone know what the plane hit upon landing?? There is [at a minimum] damage to
the spinner and prop.? There does not appear to be anything in the vicinity that
caused the damage.? Could it have happened in the air??
Jeff
-----Original Message-----
From: Robin Marks <robin1@mrmoisture.com>
Sent: Sat, 20 Oct 2007 11:39 pm
Subject: RE: RV10-List: For What It's Worth...
Jeff,
I am not sure if your email was "out of the blue" or in response
to the article on the cover of the LA times California section today.
That EXACT plane made an emergency landing near seal beach yesterday
(Friday) after the engine quit while doing aerobatics over the ocean.
Now I know why they leave the wheel pants off; sand landings.
There is a brief bit of video on the LA times site but I don't
know how long it will be posted.
http://www.latimes.com/news/local/?track=leftnav-local
80% of the way down on the right (look for video = 10/18 Plane Makes
Emergency Lading on Beach).
Robin
Do Not Archive
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Jeff
Carpenter
Sent: Friday, October 19, 2007 9:14 PM
Subject: RV10-List: For What It's Worth...
In May last year... with great trepidation... I went down to Fullerton
Airport for the "Combat Fighter Pilot Experience" that my wife had given
me as a birthday present. That's me in the front seat off for the
wildest ride of my life.
________________________________________________________________________
Email and AIM finally together. You've gotta check out free AOL Mail! - http://mail.aol.com
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: For What It's Worth... |
If you follow my link at the base of the e-mail you'll see stills
from the beach landing... so no, not out of the blue. As I was
watching the news report I couldn't stop thinking about how familiar
that plane looked.
On Oct 20, 2007, at 8:39 PM, Robin Marks wrote:
>
> Jeff,
> I am not sure if your email was "out of the blue" or in response
> to the article on the cover of the LA times California section today.
> That EXACT plane made an emergency landing near seal beach yesterday
> (Friday) after the engine quit while doing aerobatics over the ocean.
> Now I know why they leave the wheel pants off; sand landings.
> There is a brief bit of video on the LA times site but I don't
> know how long it will be posted.
> http://www.latimes.com/news/local/?track=leftnav-local
> 80% of the way down on the right (look for video = 10/18 Plane Makes
> Emergency Lading on Beach).
>
> Robin
> Do Not Archive
>
>
> -----Original Message-----
> From: owner-rv10-list-server@matronics.com
> [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Jeff
> Carpenter
> Sent: Friday, October 19, 2007 9:14 PM
> To: rv10-list@matronics.com
> Subject: RV10-List: For What It's Worth...
>
> In May last year... with great trepidation... I went down to Fullerton
> Airport for the "Combat Fighter Pilot Experience" that my wife had
> given
> me as a birthday present. That's me in the front seat off for the
> wildest ride of my life.
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV10s to Copperstate |
David, what about yours? Will be there Saturday to see all who come.
John
________________________________
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David McNeill
Sent: Saturday, October 20, 2007 10:44 PM
Subject: RV10-List: RV10s to Copperstate
Any 10s planning to make Copperstate?
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV10s to Copperstate |
Not quite. Fuselage still sitting in garage. FF done except now doing
cowling and wheelpants. Will drag to airport in November and install wings
and tail in December. Will get serious in January with first flight about
January 45?
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of John W. Cox
Sent: Sunday, October 21, 2007 9:18 AM
Subject: RE: RV10-List: RV10s to Copperstate
David, what about yours? Will be there Saturday to see all who come.
John
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David McNeill
Sent: Saturday, October 20, 2007 10:44 PM
Subject: RV10-List: RV10s to Copperstate
Any 10s planning to make Copperstate?
<http://www.matronics.com/Navigator?RV10-List>
http://www.matronics.com/Navigator?RV10-List
<http://forums.matronics.com> http://forums.matronics.com
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: For What It's Worth... |
>
> Anyone know what the plane hit upon landing? There is [at a minimum]
> damage to the spinner and prop. There does not appear to be anything in the
> vicinity that caused the damage. Could it have happened in the air?
My guess is that it nosed over on landing causing the damage, not in the
air. Just a guess though.
-Jim
do not archive
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Another 10 gets paint |
After 200 hours and 1 year of flying my RV-10, I finally got around to
taking it to the paint shop. I took it to Bobby Potts in Tuscaloosa, AL
(conveniently only an hour drive away) and he did a great job. I painted my
first few projects myself and decided I wasn't up to the task and wanted it
to finally get done.
Flightline Interiors setup should be to me in late Dec and then I can
finally call it finished, for awhile anyway ;)
Reduced size pictures are (hopefully) attached.
If anyone would like contact info for Bobby just let me know. He was great
to work with. He is pretty busy though so plenty of lead time is good.
There may be additional reports on him at Vansairforce.net
Marcus
40286
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Looking to buy a RV 10 |
I have found a RV 10 I like. I have spoken to the owner multiple times,
reviewed data looked at pictures etc...I am prepared to take it to the
next step and get a prepurchase inspection. The plane is in the south.
Does anyone know of a quality and RV 10 knowledgeable inspector.
I appreciate any help available.
David
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Looking to buy a RV 10 |
John Cox would always be a good choice. Either way I would make sure they
are knowledgeable in RV construction and are preferably an A&P. Where in t
he south and who is the builder?
Michael
From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@m
atronics.com] On Behalf Of David C. Watterson
Sent: Sunday, October 21, 2007 5:41 PM
Subject: RV10-List: Looking to buy a RV 10
I have found a RV 10 I like. I have spoken to the owner multiple times, rev
iewed data looked at pictures etc...I am prepared to take it to the next st
ep and get a prepurchase inspection. The plane is in the south. Does anyone
know of a quality and RV 10 knowledgeable inspector.
I appreciate any help available.
David
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
I am not an "Inspector" but an EAA Tech Advisor and have built my
10. Depending on the location, I might be able to help you if my
qualifications are good enough for you.
Rob.
On Oct 21, 2007, at 6:40 PM, David C. Watterson wrote:
> I have found a RV 10 I like. I have spoken to the owner multiple
> times, reviewed data looked at pictures etc...I am prepared to take
> it to the next step and get a prepurchase inspection. The plane is
> in the south. Does anyone know of a quality and RV 10 knowledgeable
> inspector.
>
> I appreciate any help available.
>
> David
>
>
Message 10
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
Alabama. The plane is owned by Jeff Dennis and built by Jeff and a
AP/builder by the name of Steve ?.
Who and where is John Cox?
David
----- Original Message -----
From: RV Builder (Michael Sausen)
To: rv10-list@matronics.com
Sent: Sunday, October 21, 2007 5:55 PM
Subject: RE: RV10-List: Looking to buy a RV 10
John Cox would always be a good choice. Either way I would make sure
they are knowledgeable in RV construction and are preferably an A&P.
Where in the south and who is the builder?
Michael
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David C.
Watterson
Sent: Sunday, October 21, 2007 5:41 PM
To: rv10-list@matronics.com
Subject: RV10-List: Looking to buy a RV 10
I have found a RV 10 I like. I have spoken to the owner multiple
times, reviewed data looked at pictures etc...I am prepared to take it
to the next step and get a prepurchase inspection. The plane is in the
south. Does anyone know of a quality and RV 10 knowledgeable inspector.
I appreciate any help available.
David
http://www.matronics.com/Navigator?RV10-Listhttp://forums.matronics.com
Message 11
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
The plane is in Musselshoels, ALA
----- Original Message -----
From: Rob Kermanj
To: rv10-list@matronics.com
Sent: Sunday, October 21, 2007 6:04 PM
Subject: Re: RV10-List: Looking to buy a RV 10
I am not an "Inspector" but an EAA Tech Advisor and have built my 10.
Depending on the location, I might be able to help you if my
qualifications are good enough for you.
Rob.
On Oct 21, 2007, at 6:40 PM, David C. Watterson wrote:
I have found a RV 10 I like. I have spoken to the owner multiple
times, reviewed data looked at pictures etc...I am prepared to take it
to the next step and get a prepurchase inspection. The plane is in the
south. Does anyone know of a quality and RV 10 knowledgeable inspector.
I appreciate any help available.
David
http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
Message 12
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
Vic Syracuse has built several planes including a gorgeous RV-10 and is also a
DAR. He's located in GA.
Gary Specketer also spends his winters in GA and has also built several planes
including an award winning GlasAir III and is in the finishing stages on an RV-10.
Gary is a Tech Counselor.
I don't have their contact info handy but you can probably find it by either searching the RV-10 list or on Tim O's website http://www.myrv10.com
Bob #40105
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=141028#141028
Message 13
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | WD-1002 / F1001B / F1040 Fuse channel rivet holes |
Hi
Last night I started match drilling the holes in the WD1002 steel weldment
that is attached to the firewall. Using the guide holes in the F-1001B as a
guide and after clamping the top WD-1002 flange to get the best edge
clearance possible, I still only got a 3/32 edge clearance (measured from
the edge of the rivet hole) on most of the holes.
Given that that the weldments are steel and not aluminium is this edge
clearance sufficient?
The archives indicate that that these parts have been problematic for some.
Based on what I read, I knew to be fairly aggressive in clamping the parts
to get the most clearance possible. Interestingly, I did have to shim the
side (towards the skin) WD-1002 flanges about a 1/8" to get reasonable edge
clearance. Even so, the maximum edge clearance would be just over 1/8" if
the rivets were evenly spaced on the flange. This suggests that 3/16"
spacing might be okay in this application.
Personally, I think this is one area where the plans should give the builder
a bit of a heads up as to what to do and what to expect.
Any comments or should I talk to the Van's order desk yet again..
Cheers
Les Kearney
#40643 - Frustrated in the fuse ..
Message 14
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV10s to Copperstate |
I believe N110GS will be there.
Do not archive
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
www.saintaviation.com
Cell: 352-427-0285
Fax: 815-377-3694
_____
From: John W. Cox [mailto:johnwcox@pacificnw.com]
Sent: Sunday, October 21, 2007 11:18 AM
Subject: RE: RV10-List: RV10s to Copperstate
David, what about yours? Will be there Saturday to see all who come.
John
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David McNeill
Sent: Saturday, October 20, 2007 10:44 PM
Subject: RV10-List: RV10s to Copperstate
Any 10s planning to make Copperstate?
<http://www.matronics.com/Navigator?RV10-List>
http://www.matronics.com/Navigator?RV10-List
<http://forums.matronics.com> http://forums.matronics.com
Message 15
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Looking to buy a RV 10 |
My records show Jeff Dennis the builder of kit #40517 in Tuscumbia, AL
and registered as N2733K. My quick take is that Vic Syracuse is the
best DAR/advisor in the south and would be my very first choice. That
was a FAST build completion and Vic would know exactly where the corners
were cut and shortcuts taken. The kit is an excellent choice regardless
of the build quality which should only effect sales price.
Why is it being sold? And So soon. Did you know that Vic's is for sale
too? Congratulations on selecting the world's finest metal and
composite 4 place aircraft for the dollar.
I am in Aurora, Oregon (KUAO - Home of VANS) and fly Non-rev with my
airline to non-west coast locations.
John
503-453-6016
________________________________
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David C.
Watterson
Sent: Sunday, October 21, 2007 4:06 PM
Subject: Re: RV10-List: Looking to buy a RV 10
Alabama. The plane is owned by Jeff Dennis and built by Jeff and a
AP/builder by the name of Steve ?.
Who and where is John Cox?
David
----- Original Message -----
From: RV Builder (Michael Sausen) <mailto:rvbuilder@sausen.net>
To: rv10-list@matronics.com
Sent: Sunday, October 21, 2007 5:55 PM
Subject: RE: RV10-List: Looking to buy a RV 10
John Cox would always be a good choice. Either way I would make
sure they are knowledgeable in RV construction and are preferably an
A&P. Where in the south and who is the builder?
Michael
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of David C.
Watterson
Sent: Sunday, October 21, 2007 5:41 PM
To: rv10-list@matronics.com
Subject: RV10-List: Looking to buy a RV 10
I have found a RV 10 I like. I have spoken to the owner multiple
times, reviewed data looked at pictures etc...I am prepared to take it
to the next step and get a prepurchase inspection. The plane is in the
south. Does anyone know of a quality and RV 10 knowledgeable inspector.
I appreciate any help available.
David
http://www.matronics.com/Navigator?RV10-List
http://forums.matronics.com
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s
.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
Message 16
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
DAVID, DROP ME AN EMAIL.....DOUGPFLYRV@AOL.COM.
DOUG PRESTON
#40372
-----Original Message-----
From: David C. Watterson <dcw@dddirectories.com>
Sent: Sun, 21 Oct 2007 5:40 pm
Subject: RV10-List: Looking to buy a RV 10
I have found a RV 10 I like. I have spoken to the
owner multiple times, reviewed data looked at pictures etc...I am prepared to
take it to the next step and get a prepurchase inspection. The plane is in the
south. Does anyone know of a quality and RV 10 knowledgeable
inspector.
?
I appreciate any help available.
?
David
________________________________________________________________________
Email and AIM finally together. You've gotta check out free AOL Mail! - http://mail.aol.com
Message 17
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking to buy a RV 10 |
Vic's sold a couple weeks ago.
Tim Olson - RV-10 N104CD - Flying
do not archive
John W. Cox wrote:
>
> Why is it being sold? And So soon. Did you know that Vics is for sale
> too?
Message 18
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I'll be using a few steam gauges to supplement my EFIS. We don't
seem to talk about these much, but are there preferred makes/models
of air speed indicators, altimeters and the like? Who makes the best
compass, or the best electric DG?
Jeff Carpenter
40304
about to join the forward and mid fuse...
N410CF (now a small light at the end of a very long tunnel)
Message 19
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV10s to Copperstate |
Not me unfortunately. =0AI want to go but I will be on a cruise. Trust me
, I would rather be at Copperstate. Take lots of pictures. =0AI am going t
o be at Nellis for the airshow if all my paperwork goes through without cau
sing them to go to DEFCON 1. =0A =0ATonight I finally finished my annual.
Had to borrow Mike Howe's front bearings from his finishing kit. Both of m
ine had tears in the rubber. Matco is located 300 yards from my hanger and
I'm going to talk with them this week and see what might have caused this.
=0A=0AAnyone located at Van Nuys? Should be there Wednesday. Hopefully I g
et to land on 16R. =0A =0AScott Schmidt=0Ascottmschmidt@yahoo.com=0A=0A----
- Original Message ----=0AFrom: David McNeill <dlm46007@cox.net>=0ATo: rv10
-list@matronics.com=0ASent: Saturday, October 20, 2007 11:43:50 PM=0ASubjec
t: RV10-List: RV10s to Copperstate=0A=0A=0A=0A=0A=0A =0A =0A=0A<!--=0A=0A /
* Style Definitions */=0A p.MsoNormal, li.MsoNormal, div.MsoNormal=0A{ma
rgin:0in;margin-bottom:.0001pt;font-size:12.0pt;font-family:"Times New Roma
n";}=0Aa:link, span.MsoHyperlink=0A{color:blue;text-decoration:underline
;}=0Aa:visited, span.MsoHyperlinkFollowed=0A{color:purple;text-decoratio
n:underline;}=0Aspan.EmailStyle17=0A{font-family:Arial;color:windowtext;
}=0A _filtered {margin:1.0in 1.25in 1.0in 1.25in;}=0Adiv.Section1=0A{}
=0A-->=0A=0A=0A=0A=0A=0A=0A =0A =0A=0AAny 10s planning to make Copperstate
==============0A=0A=0A=0A=0A
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|