---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sat 05/17/08: 8 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:12 AM - Re: Re: 1000 Mile Rule? (Fixitauto@aol.com) 2. 11:41 AM - Ignition Cable clamp (Michael Wellenzohn) 3. 12:01 PM - Re: Ignition Cable clamp (linn Walters) 4. 12:55 PM - Re: Ignition Cable clamp (Albert Gardner) 5. 06:52 PM - Re: Ignition Cable clamp (linn Walters) 6. 08:35 PM - Performance Data Point (Dave Saylor) 7. 08:55 PM - VH-ICY (Chris and Susie McGough) 8. 08:55 PM - VH-ICY (Chris and Susie McGough) ________________________________ Message 1 _____________________________________ Time: 07:12:47 AM PST US From: Fixitauto@aol.com Subject: Re: RV10-List: Re: 1000 Mile Rule? Check this out. _http://wcaircraft.com/boonervday.html_ (http://wcaircraft.com/boonervday.html) Saturday June 14 2008 This should be within 1000 miles for a lot of people. Sure would like to see some of you there. Shameless promotion of what is always a good time. **************Wondering what's for Dinner Tonight? Get new twists on family favorites at AOL Food. (http://food.aol.com/dinner-tonight?NCID=aolfod00030000000001) ________________________________ Message 2 _____________________________________ Time: 11:41:46 AM PST US Subject: RV10-List: Ignition Cable clamp From: "Michael Wellenzohn" Who knows where I can get two of these ignition cable clamps (for three cables)! Michael Zuerich, Switzerland -------- RV-10 builder (engine, prop, finishing) #511 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=183556#183556 Attachments: http://forums.matronics.com//files/zndkabelklemme_113.jpg ________________________________ Message 3 _____________________________________ Time: 12:01:06 PM PST US From: linn Walters Subject: Re: RV10-List: Ignition Cable clamp I don't know a source, but you can take a plain ADEL clamp (a 1 1/4" should do it) and remove the rubber part. Put a screw through the hole and tighten up a nut. Place a 3/8" thick piece of 'something' in the clamp and squeeze in a vise to make the clamp oblong. Replace the rubber part and you should have a usable clamp. Linn Michael Wellenzohn wrote: > > Who knows where I can get two of these ignition cable clamps (for three cables)! > > Michael > Zuerich, Switzerland > > -------- > RV-10 builder (engine, prop, finishing) > #511 > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=183556#183556 > > > Attachments: > > http://forums.matronics.com//files/zndkabelklemme_113.jpg > > > ________________________________ Message 4 _____________________________________ Time: 12:55:29 PM PST US From: "Albert Gardner" Subject: RE: RV10-List: Ignition Cable clamp Are you thinking of the Engine Baffle Ignition Wire Seals like on aircraft Spruce cat/ page 272? Or something else? Albert Gardner Yuma, AZ -----Original Message----- RV10-List message posted by: "Michael Wellenzohn" Who knows where I can get two of these ignition cable clamps (for three cables)! Michael Zuerich, Switzerland ________________________________ Message 5 _____________________________________ Time: 06:52:40 PM PST US From: linn Walters Subject: Re: RV10-List: Ignition Cable clamp Duh!!! Good question!!!! If he is looking for the baffle feed-through clamps ..... makes my suggestion seem pretty stupid!!! But then again, if someone is looking for ignition clamps that attach to the valve covers ..... Bingo!!! Linn do not archive!! Albert Gardner wrote: > > Are you thinking of the Engine Baffle Ignition Wire Seals like on aircraft > Spruce cat/ page 272? Or something else? > Albert Gardner > Yuma, AZ > > -----Original Message----- > Who knows where I can get two of these ignition cable clamps (for three > cables)! > Michael > Zuerich, Switzerland > > > ________________________________ Message 6 _____________________________________ Time: 08:35:50 PM PST US From: "Dave Saylor" Subject: RV10-List: Performance Data Point We took off from Palm Springs this afternoon. It was HOT, but the plane performed flawlessly. OAT was 38C, DA 3250' We opted for the long runway, but it wasn't necessary. We used 1/3 flaps but did not lean for takeoff. We "rolled" into the departure, and were off before the threshold. I used Google Earth to estimate the takeoff distance--very close to 1250'. Climb was just a little less than normal. I was worried about oil temp, which got to the bottom of the yellow by around 6000'. We nosed over a bit until it cooled and then just continued the climb (at that point we were passing 1000' over a Mooney that took off in front of us...). Takeoff weight was about 2450 CHT was always around 385. This is a great plane! ________________________________ Message 7 _____________________________________ Time: 08:55:36 PM PST US From: "Chris and Susie McGough" Subject: RV10-List: VH-ICY VH-ICY signed off today. Can you believe the Dynon crapped itself so cant fly till its fixed.....oh well another couple of weeks to check everything regards Chris 388 ________________________________ Message 8 _____________________________________ Time: 08:55:36 PM PST US From: "Chris and Susie McGough" Subject: RV10-List: VH-ICY VH-ICY signed off today. Can you believe the Dynon crapped itself so cant fly till its fixed.....oh well another couple of weeks to check everything regards Chris 388 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.