Today's Message Index:
----------------------
1. 08:36 AM - Re: Slick mag update SB2-08A and SB3-08A (Chuck Weyant)
2. 09:51 AM - Thank you on the 51% responses (John Cox)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Slick mag update SB2-08A and SB3-08A |
Purchased brand new Slicks about three months ago from Spruce. Installed
them on the engine but not run yet. What would you do, send them back for
refund then repurchase? What?
Chuck
----- Original Message -----
From: "Rhonda Bewley" <Rhonda@bpaengines.com>
Sent: Monday, September 29, 2008 12:48 PM
Subject: RE: RV10-List: Slick mag update SB2-08A and SB3-08A
>
> My understanding is that the kits are on back order due to
> "overwhelming" response. Go figure. Another option would be to purchase
> the brushes and cams through a shop like Quality Aircraft Accessories
> (918) 835-6948. Quality will also do the labor for $75/mag, if new/low
> time. If more than 100 hours, I think they are charging a little bit
> more.
>
> Best,
>
> Rhonda
>
> -----Original Message-----
> From: owner-rv10-list-server@matronics.com
> [mailto:owner-rv10-list-server@matronics.com] On Behalf Of MauleDriver
> Sent: Monday, September 29, 2008 1:32 PM
> To: rv10-list@matronics.com
> Subject: Re: RV10-List: Slick mag update SB2-08A and SB3-08A
>
>
> I'm subject to the bulletin and I want to get the kit. I've been trying
>
> to reach Unison on the phone but get no answer or call back. I've
> searched the site and come up empty handed.
>
> I have a Lycoming YIO-540.
>
> Can anyone point me to a contact or URL where I can go about getting the
>
> kit?
>
> Thanks.
>
> Tim Olson wrote:
>>
>> Unison Revises Slick Magneto Service Bulletin; Kits Available
>> Unison Industries has revised service bulletins on its Slick magnetos
>> and is currently shipping kits to enable compliance with the revised
>> SBs. Service bulletins SB2-08A and SB3-08A are revisions of earlier
>> bulletins. For affected Slick- and LASAR-brand magnetos (serial
>> numbers from 0610XXXX to 0804XXXX), installing the kits will
>> constitute a terminating action for the SBs. Others that might be
>> affected are magnetos that have had their cam (or the cam as part of
>> the contact point assembly kit) replaced with products shipped between
>
>> October 1, 2006, and May 11, 2008. Unison is recommending replacing
>> the entire contact point assembly and distributor block and gear
>> assemblies. Service Bulletin SB3-08A affects magnetos with serial
>> numbers from 0409XXXX to 08080453, and/or magnetos that have had the
>> carbon brush or distributor block replaced with products shipped
>> between September 1, 2004, and August 14, 2008. For a limited time,
>> the company is making the kits available at reduced prices. Any Slick
>> or LASAR magnetos manufactured after August 15, 2008, are not affected
>
>> by the SBs. For more information, go to
> http://www.unisonindustries.com/
>>
>> https://unisonpubs.com/docs/F-1100-SB3-08A.pdf
>>
>>
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Thank you on the 51% responses |
In four hours the deadline is nearing for comments. Thanks to those 300
soles who took the time to share their recommendations.
It was unfortunate that the FAA/EAA posted the wrong phone number for
FAXing responses. I sent mine by both email and FAX. The correct FAX
number to Miguel was 202-267-5580.
The ARC will soon review the comments and the final policy will be
implemented in a month.
John Cox
#600
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|