Today's Message Index:
----------------------
1. 01:08 PM - Re: Comm 2 volume Very low (Chris and Susie)
2. 01:58 PM - Re: Comm 2 volume Very low (Bob Turner)
3. 03:28 PM - Re: Re: Comm 2 volume Very low (Chris and Susie)
4. 05:09 PM - Re: Comm 2 volume Very low (Deems Davis)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Comm 2 volume Very low |
Deems I have a diferent intercom but had a similar problem. I had to put a
1/4 watt 300 ohm resistor from the audio output from SL40 to input from
intercom.
regards Chris
----- Original Message -----
From: "Deems Davis" <deemsdavis@cox.net>
Sent: Saturday, May 23, 2009 9:38 AM
Subject: RV10-List: Comm 2 volume Very low
>
> My Com2 Garmin SL40 which is connected through a Garmin 340 audio panel
> produces only a fraction of the volume, that the Com1 SL 30 does. I've
> been through the manuals looking for a clue as to where to begin. The
> audio panel states that the volume is controlled by the volume control on
> the radios. The Comm2 Vol is at max level. Anybody got suggestions on
> where to look?
>
> THANKS
>
> Deems Davis
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Comm 2 volume Very low |
Chris' problem/solution is characteristic of a very inexpensive intercom, where
all radio inputs are connected together instead of a proper mixing circuit. Surely
not the problem with the garmin audio panel.
Deems, if you have a pin extractor, try swapping the SL 30 to com2 input, and the
SL40 to com1 input, on the audio panel. If the problem stays with the SL40,
then the problem is there. If the problem switches to the SL30, then the problem
is in the audio panel. That will give you a starting point.
But check the easy things first, like the setup menus.
--------
Bob Turner
RV-10 QB
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=245080#245080
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Comm 2 volume Very low |
Your probably right Bob. Hopefully with the US Dollar continualy dropping I
will be able to upgrade to a better panel shortly.
Chris VH-ICY
----- Original Message -----
From: "Bob Turner" <bobturner@alum.rpi.edu>
Sent: Sunday, May 24, 2009 6:57 AM
Subject: RV10-List: Re: Comm 2 volume Very low
>
> Chris' problem/solution is characteristic of a very inexpensive intercom,
> where all radio inputs are connected together instead of a proper mixing
> circuit. Surely not the problem with the garmin audio panel.
>
> Deems, if you have a pin extractor, try swapping the SL 30 to com2 input,
> and the SL40 to com1 input, on the audio panel. If the problem stays with
> the SL40, then the problem is there. If the problem switches to the SL30,
> then the problem is in the audio panel. That will give you a starting
> point.
>
> But check the easy things first, like the setup menus.
>
> --------
> Bob Turner
> RV-10 QB
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=245080#245080
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Comm 2 volume Very low |
Fixed /Variable is not a configuration setting available on the SL40,
only on the SL30.
Deems
Benjamin Krotje wrote:
> is your volume level set at a fixed value instead of the variable
> setting? turn of the radio and press and hold the mem button(i
> think) and turn it on and then change the values to variable
>
> --- On *Fri, 5/22/09, Deems Davis /<deemsdavis@cox.net>/* wrote:
>
>
> From: Deems Davis <deemsdavis@cox.net>
> Subject: RV10-List: Comm 2 volume Very low
> To: aeroelectric-list@matronics.com, rv10-list@matronics.com
> Date: Friday, May 22, 2009, 6:38 PM
>
> <http://us.mc655.mail.yahoo.com/mc/compose?to=deemsdavis@cox.net>>
>
> My Com2 Garmin SL40 which is connected through a Garmin 340 audio
> panel produces only a fraction of the volume, that the Com1 SL 30
> does. I've been through the manuals looking for a clue as to
> where to begin. The audio panel states that the volume is
> controlled by the volume control on the radios. The Comm2 Vol is
> at max level. Anybody got suggestions on where to
> looht="http://forums.matronics.com/"
> target=_blank>http://forums.matronics.c
> &nbsf="http://www.matronics.com/contribution" ======
>
>
> <http://www.matronics.com/Navigator?RV10-List>
>
>
> *
>
>
> *
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|