---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 09/06/09: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:01 AM - Re: New garmin traffic system was announced (tomhanaway) 2. 06:14 AM - Re: Re: New garmin traffic system was announced (Jesse Saint) 3. 07:37 AM - Re: New garmin traffic system was announced (tomhanaway) 4. 09:14 AM - Pro-Seal Removal (Barry Marz) 5. 03:53 PM - Re: Pro-Seal Removal (Kelly McMullen) 6. 08:44 PM - Moving to the airport (aerosport1) ________________________________ Message 1 _____________________________________ Time: 05:01:42 AM PST US Subject: RV10-List: Re: New garmin traffic system was announced From: "tomhanaway" I can speak to the Navworx install as I'm going through it now. Bill Moffitt, their rep/owner? is tough to reach so send him an email (address at their site). Basically, two antennas (gps and uat-on the 10 I'm putting mine top and bottom on forward end of tailcone-rg400 antenna cable w/bnc connectors), encoder wire from EFIS or transponder, couple of wires to display (efis or x96). He'll send you the full install instructions if you ask. I'll be glad to send them if Bill M. says it's ok. Incredibly easy install although definitely not flying yet. The money spent on this was saved by getting the gtx327 instead of the gtx330. Of course, in Florida we have extensive ads-b coverage. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=261711#261711 ________________________________ Message 2 _____________________________________ Time: 06:14:55 AM PST US From: Jesse Saint Subject: Re: RV10-List: Re: New garmin traffic system was announced I just helped someone install a Navworx box too. As you said, fairly easy install. We put it in the exact same place, it sounds like. It was a little unclear, I thought, for hooking up to an AFS screen, but Bill helped us out. In my experience Bill was easy to get ahold of. Every time I called he answered the phone. It does seem a little archaic to have to use a terminal emulator to setup their box, but I guess there's no other way without a screen or a special program (like Dynon uses). We have had some functionality issues, but are still troubleshooting. Overall it seems like a great option instead of mode- S for those who live around good ADS-B coverage, like in FL or up and down the east coast. Be aware, however, that AFS doesn't currently show weather and it's likely they won't for some time with all their efforts thrown towards their 4500 line. Jesse Saint Saint Aviation jesse@saintaviation.com 352-427-0285 Sent from my iPhone On Sep 6, 2009, at 8:00 AM, "tomhanaway" wrote: > > I can speak to the Navworx install as I'm going through it now. > Bill Moffitt, their rep/owner? is tough to reach so send him an > email (address at their site). > > Basically, two antennas (gps and uat-on the 10 I'm putting mine top > and bottom on forward end of tailcone-rg400 antenna cable w/bnc > connectors), encoder wire from EFIS or transponder, couple of wires > to display (efis or x96). > > He'll send you the full install instructions if you ask. I'll be > glad to send them if Bill M. says it's ok. > > Incredibly easy install although definitely not flying yet. > > The money spent on this was saved by getting the gtx327 instead of > the gtx330. Of course, in Florida we have extensive ads-b coverage. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=261711#261711 > > ________________________________ Message 3 _____________________________________ Time: 07:37:15 AM PST US Subject: RV10-List: Re: New garmin traffic system was announced From: "tomhanaway" Jesse's correct about no weather display from ads-b on AFS screen. I'm doing AFS units and plan to run the weather from xm. Either to 696 or efis depending on which looks better/is available. Tom H Read this topic online here: http://forums.matronics.com/viewtopic.php?p=261732#261732 ________________________________ Message 4 _____________________________________ Time: 09:14:15 AM PST US From: Barry Marz Subject: RV10-List: Pro-Seal Removal I had to remove the Pro-Seal from a C-421 windshield frame and retainers; a Harbor Freight Pneumatic Scraper with a polycarbonate blade we made worked great. The Pro-Seal was built up 1/4" in places and it pealed it off without hurting the aluminum. Blue Skys Barry Marz 18735 Baseleg AVE. FT. Myers, Fl 33917 239-567-2271 blalmarz@embarqmail.com ________________________________ Message 5 _____________________________________ Time: 03:53:42 PM PST US Subject: Re: RV10-List: Pro-Seal Removal From: Kelly McMullen Avery has this tool: http://www.averytools.com/pc-1055-80-sr-sealant-cutters.aspx I've used sharpened plexiglass strips. There are phenolic and hard plastic scrapers for the job. There is a stripper called Polygone AG that slowly disolves proseal. Just finishing up a full strip and reseal of a Mooney wet wing tank. Used the Polygone to remove more difficult areas like rivet heads and in seams between spar and ribs/skins. However you do it, avoid metal scrapers, metal wire wheels, etc that will remove alclad layer. On Sun, Sep 6, 2009 at 9:13 AM, Barry Marz wrote: > > I had to remove the Pro-Seal from a C-421 windshield frame and retainers; a > Harbor Freight Pneumatic Scraper with a polycarbonate blade we made worked > great. The Pro-Seal was built up 1/4" in places and it pealed it off without > hurting the aluminum. Blue Skys > > Barry Marz > 18735 Baseleg AVE. > FT. Myers, Fl 33917 > 239-567-2271 > blalmarz@embarqmail.com > > ________________________________ Message 6 _____________________________________ Time: 08:44:59 PM PST US Subject: RV10-List: Moving to the airport From: "aerosport1" I finally got the plane moved to the airport. All went well and had plenty of great help. Thanks to all who helped. Bob Leffler, Brad Leffler, Jim Baldwin, Jack Ferernce, Al Moyer, Pat Ferguson, Matt Finley and Cals towing. When I called to get prices on roll backs Cals Towing thought I was joking when I said I need to have an airplane towed. The end is getting near Below is a link to more photos Geoff http://www.phanfare.com/album/#vw=album&ac=default&aid=3161550&sid=-1 -------- Geoff Combs RV-10 QB N829GW Finishing Read this topic online here: http://forums.matronics.com/viewtopic.php?p=261813#261813 Attachments: http://forums.matronics.com//files/img_2362_web_165.jpg ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.