Today's Message Index:
----------------------
1. 05:11 AM - Re: Door Pin - Idea (Robert Brunkenhoefer)
2. 08:48 AM - Sealing Firewall Penetrations (Les Kearney)
3. 09:07 AM - Re: Sealing Firewall Penetrations (Perry, Phil)
4. 10:01 AM - Re: N829GW Maiden flight (Richard Barnes)
5. 10:30 AM - Re: N829GW Maiden flight (orchidman)
6. 12:36 PM - Re: Copperstate RV10 nest (woxofswa)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Door Pin - Idea |
my mechanic had a difficult time making the blocks fit also. we only
did one door for now because of it. hole size too small, block too
wide in places . robert
On Oct 27, 2009, at 10:48 AM, Miller John wrote:
> Dave,
>
> I'm going to keep the tie downs.
>
> Will get a check in the mail to you today.
>
> Thanks - grumpy
>
> On Oct 6, 2009, at 12:34 PM, Dave Saylor wrote:
>
>> Fifth item down:
>>
>> http://www.aircraftersllc.com/products.htm
>>
>> Dave Saylor
>> AirCrafters LLC
>> 140 Aviation Way
>> Watsonville, CA 95076
>> 831-722-9141 Shop
>> 831-750-0284 Cell
>>
>>
>> On Tue, Oct 6, 2009 at 9:56 AM, Miller John <gengrumpy@aol.com>
>> wrote:
>> It would be nice to have a metal block the exact same size as the
>> nylon one for retrofit.
>>
>> The bullet and block would not retrofit to my door.....
>>
>> grumpy
>> N184JM
>>
>> Do not archive
>>
>>
>>
>> ===================================
>> tp://www.matronics.com/Navigator?RV10-List
>> ===================================
>> nics.com
>> ===================================
>> w.matronics.com/contribution
>> ===================================
>>
>
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Sealing Firewall Penetrations |
Hi
I am just about ready to rivet in the center recess of the firewall. I am
wonder what the best product would be to seal this in as well as perhaps
some of the other firewall penetrations. I am planning to use stainless
eyeball penetrations from ACS as well as a SAFEAIR1 firesleeve penetration
for wiring. From what I have read fuel tank sealant is good to 400c while
wind blown avgas burns at 2,000c.
What is the current list thinking on this subject?
Cheers
Les
#40643 - Living in f/g hell
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Sealing Firewall Penetrations |
Here is one for you.
http://www.flamemaster.com/TechnicalsPDF/cs1900.pdf
From: Les Kearney [mailto:kearney@shaw.ca]
Sent: Wednesday, October 28, 2009 10:47 AM
Subject: RV10-List: Sealing Firewall Penetrations
Hi
I am just about ready to rivet in the center recess of the firewall. I
am wonder what the best product would be to seal this in as well as
perhaps some of the other firewall penetrations. I am planning to use
stainless eyeball penetrations from ACS as well as a SAFEAIR1 firesleeve
penetration for wiring. From what I have read fuel tank sealant is good
to 400c while wind blown avgas burns at 2,000c.
What is the current list thinking on this subject?
Cheers
Les
#40643 - Living in f/g hell
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | N829GW Maiden flight |
Congratulations. A beautiful plane and a great looking panel. It looks
like you got one of the 4500's. We're still waiting for ours. How does the
4500 work?
Rick
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of aerosport1
Sent: Tuesday, October 27, 2009 2:53 PM
Subject: RV10-List: N829GW Maiden flight
<g.combs@aerosportmodeling.com>
After 2 years and 20 days.
On 10-26-09 at 4:30 PM N829GW took it's maiden flight with myself at the
controls. I flew for 40 minutes and all went well. I now need to fly off 40
hours before I can start taking trips and passengers. And then My wife's
honey dew list kicks into high gear.
That RVgrin just keeps giving and giving
What a great airplane
Geoff
--------
Geoff Combs
RV-10 QB N829GW
Finishing
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=269702#269702
Attachments:
http://forums.matronics.com//files/air1_107.jpg
http://forums.matronics.com//files/landg_n829gw_671.jpg
http://forums.matronics.com//files/panel2_806.jpg
http://forums.matronics.com//files/rvgrin_528.jpg
http://forums.matronics.com//files/right_n829gw_162.jpg
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: N829GW Maiden flight |
velo wrote:
> Congratulations. A beautiful plane and a great looking panel. It looks
> like you got one of the 4500's. We're still waiting for ours. How does the
> 4500 work?
> Rick
> --
Rick,
ONE [Shocked] Looks like he kyped 2 of the 4500's [Mr. Green]
--------
Gary Blankenbiller
RV10 - # 40674
(N2GB Flying)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=269866#269866
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Copperstate RV10 nest |
There was a tanned silvered haired fellow that came for lunch. I didn't catch
his name and I believe he came as a guest of another builder.
He came back when we were packing up and got a couple of drinks out of the cooler
inside the trailer. I am pretty sure that he is the fellow who left the camera.
If he sounds familiar to anyone please help me get this camera back to
him.
Myron
602 421 2868
--------
Myron Nelson
Mesa, AZ
Emp completed, legacy build fuse in progress
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=269881#269881
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|