Today's Message Index:
----------------------
1. 05:07 AM - Re: Re: Fuel Related Items (George, Neal E Capt USAF ACC 505 TRS/DOJ)
2. 11:45 AM - Re: Gear intersection fairing - bonding lower fairing to wheel pant (Dave Saylor)
3. 02:51 PM - Main Door Hinges (Dave Ward)
4. 10:36 PM - Prop governor adapter (David White)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RE: Fuel Related Items |
Phil -
Unless Andair has changed their valves, you can't just bolt an extension
between the handle and the body. The valve body is machined to interact
with the handle parts to provide the stops and locking mechanism. The
extension kit is more than a chunk of extruded tube. The heart of an
extension kit is a bezel machined to replicate the top of the valve body
so the stops and off-locks still function.
neal
=====================
I=99ll just order the FS20x7T from Vans and take you up on your
offer for the extension. I=99m guessing you can retro fit the
standard valve.
Phil
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gear intersection fairing - bonding lower fairing to wheel |
pant
Bill,
Here are some pics of our wheel pants. The gap you see opened up on the
inner split line because there isn't a screw closer to the top of the
intersection, just the one on the very bottom. Others look nicer so if you
can think of some way to pull the split line together you could probably
avoid the gap you seen on mine.
Dave Saylor
AirCrafters LLC
140 Aviation Way
Watsonville, CA 95076
831-722-9141 Shop
831-750-0284 Cell
On Mon, Mar 29, 2010 at 2:29 PM, Bill Mauledriver Watson <
MauleDriver@nc.rr.com> wrote:
> MauleDriver@nc.rr.com>
>
> I seem to recall that a few people have bonded the lower intersection
> fairing to the wheel pant but can't remember who. If you've done it and
> have some pics, please share or point me to them.
>
> It's starting to make some sense to me right now.
>
> Thanks
> Bill "pants on the ground" Watson
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Main Door Hinges |
AirWard has developed another upgrade kit for the RV-10 line. We have a
replacement to the original installation procedure for attaching the
main doors to the canopy. So much emphasis has been concentrated on the
main door latch system and no consideration for the two hinges holding
the main door to the canopy. This 1/8" fiberglass with four countersunk
screws is subject to quite a bit of tension when both latching the main
door and when the door is in the up position. Our Kit has all the parts
for four latches. See the attached brochure for pictures. We also have
the Parking Brake Valve Kit and the Tunnel Access Kit available.
Dave Ward
RV-10, just about on gear.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Prop governor adapter |
does any one on the RV10 list know where to procure one of these,,,-- ?
-- Its a prop governor adaptor for a external oil supply line-- Tha
nk-- you-- David
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|