Today's Message Index:
----------------------
0. 12:13 AM - Just A Few Days Left; Well Behind Last Year... (Matt Dralle)
1. 05:31 AM - Re: RV-10 for X-plane (johngoodman)
2. 08:47 AM - Re: Brass Torx or Socket Head Screws For Panel (Sean Stephens)
3. 08:51 AM - Off-Topic: P51 360 Degree Flash Pic (Sean Stephens)
4. 08:59 AM - Re: Re: Brass Torx or Socket Head Screws For Panel (Tim Olson)
5. 09:43 AM - Re: Oil Analysis kit info (Tim Olson)
6. 04:35 PM - Re: Re: Brass Torx or Socket Head Screws For Panel (Kelly McMullen)
7. 11:24 PM - fuel flow transducer location (rvdave)
Message 0
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Just A Few Days Left; Well Behind Last Year... |
Dear Listers,
There are just a few more days left of this year's List Fund Raiser. Response
has been good so far, but we're well behind last year at this point. If you've
been waiting until the last minute to make your Contribution, now might be good
time to show your support and maybe pick up a nice gift as well!
Please remember that there is no commercial advertising on these Lists and the
*only* means of keeping them running is through your Contributions during this
Fund Raiser. If it weren't for your individual Contributions, these Lists could
easily become economically infeasible and simply cease to exist.
You probably can't even take the family out to dinner for $20 these days, but your
individual Contribution of the same amount makes a huge difference in keeping
the List services alive.
Please make a Contribution today with a Credit Card or Paypal:
http://www.matronics.com/contribution
Or, drop a personal check in the mail to:
Matt Dralle / Matronics
581 Jeannie Way
Livermore CA 94550
Thank you!
Matt Dralle
Matronics Email List Administrator
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-10 for X-plane |
I'm the one who must be old - I didn't even know it was a game.
--------
#40572 Painted but still in pieces
N711JG reserved
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=320071#320071
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Brass Torx or Socket Head Screws For Panel |
Thanks for all the replies on and off list. It seems that it is hard to
find brass fasteners that are Black Ox coated AND are something other
than phillips or slotted head.
McMaster-Carr (which most of the replies suggested) has a great
selection of brass fasteners, but none of them that I could see were
Black Ox coated. They have steel in Black Ox, but not brass.
I guess there's always self-painting the heads.
-Sean #40303
On 11/18/10 5:36 PM, Sean Stephens wrote:
> I am trying to locate a supplier of black brass machine screws for my
> panel. I'd like to have torx or socket heads. I found a few
> suppliers of phillips head black brass machine screws like Aircraft
> Spruce, but I cannot locate any with torx or socket heads.
>
> Thanks for any info...
>
> -Sean #40303
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Off-Topic: P51 360 Degree Flash Pic |
Really cool 360 degree image of a P51 cockpit.
http://www.stclairphoto-imaging.com/360/P51-Mustang/P51_swf.html
Requires Flash and note that the colors take a loooooong time to load.
I need that switch panel on the bottom left for Guns and Bombs on the
-10. I know the regs prevent flying for hire, but do they mention
anything about strafing runs? I guess maybe just not over congested
areas? :)
-Sean #40303
DO NOT ARCHIVE
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Brass Torx or Socket Head Screws For Panel |
That's what I did on mine. Most are painted.
Tim Olson - RV-10 N104CD
do not archive
On 11/19/2010 10:42 AM, Sean Stephens wrote:
>
> Thanks for all the replies on and off list. It seems that it is hard to
> find brass fasteners that are Black Ox coated AND are something other
> than phillips or slotted head.
>
> McMaster-Carr (which most of the replies suggested) has a great
> selection of brass fasteners, but none of them that I could see were
> Black Ox coated. They have steel in Black Ox, but not brass.
>
> I guess there's always self-painting the heads.
>
> -Sean #40303
>
>
> On 11/18/10 5:36 PM, Sean Stephens wrote:
>> I am trying to locate a supplier of black brass machine screws for my
>> panel. I'd like to have torx or socket heads. I found a few suppliers
>> of phillips head black brass machine screws like Aircraft Spruce, but
>> I cannot locate any with torx or socket heads.
>>
>> Thanks for any info...
>>
>> -Sean #40303
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Oil Analysis kit info |
I just had my kits ship today and I found out that
the price below is slightly wrong. The kits
are $70/10, but with prepaid postage, they're
now $92.50. The postage is $2.25 each.
Tim Olson - RV-10 N104CD
On 11/3/2010 4:45 PM, Tim Olson wrote:
>
> A while back I did a write-up with an oil change where I
> listed my contact info for where I got my oil analysis
> test kits. At the time I got them from Shell Labs, and
> it was the best deal I could find...$70 for 10, or,
> $85/10 which includes prepaid postage. I did the latter.
>
> Last week a couple things happened. 1) I used up my
> first 10 test kits. 2) Some "polaris labs" called to
> get my contact info, telling me that they were now
> the Shell subcontracted lab. I found out that my old
> lab was now not being used by Shellcare. So, I started
> shopping again for a new oil analysis provider. Most
> prices ran $12 to $24 per sample....many are available
> for around $14 per sample.
>
> In the end though, I contacted the original company
> that shell used.
> http://www.analystsinc.com/
>
> They just sold me another 10 test kits for $85 with
> prepaid postage, so I'm set for a while again. I have
> to sign a form authorizing them my old historical info
> from Shell, but from that point on it's the same
> test lab so the sampling and reporting will be identical.
>
> The person I talked to was
> Katie
> 847-305-9955
>
> I thought I'd pass it on because oil analysis is a great
> thing for long term trending, but it's expensive if you
> don't find a good deal, and I think this was a pretty good
> deal compared to what others cost.
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Brass Torx or Socket Head Screws For Panel |
I saw a Cirrus SR-20 today that had black allen head screws for holding
the instruments. It was a fairly early 2000's model with mostly 6-pack
of steam gauges. Obviously Cirrus had to source them somewhere.
On 11/19/2010 9:42 AM, Sean Stephens wrote:
>
> Thanks for all the replies on and off list. It seems that it is hard
> to find brass fasteners that are Black Ox coated AND are something
> other than phillips or slotted head.
>
> McMaster-Carr (which most of the replies suggested) has a great
> selection of brass fasteners, but none of them that I could see were
> Black Ox coated. They have steel in Black Ox, but not brass.
>
> I guess there's always self-painting the heads.
>
> -Sean #40303
>
>
> On 11/18/10 5:36 PM, Sean Stephens wrote:
>> I am trying to locate a supplier of black brass machine screws for my
>> panel. I'd like to have torx or socket heads. I found a few
>> suppliers of phillips head black brass machine screws like Aircraft
>> Spruce, but I cannot locate any with torx or socket heads.
>>
>> Thanks for any info...
>>
>> -Sean #40303
>
>
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | fuel flow transducer location |
Plans show transducer to be in the tunnel, I've heard there are less fluctuations
if it is placed after the mechanical pump and before distribution for fuel
injection, is this correct?
--------
Dave Ford
RV6 flying
RV10 building
Cadillac, MI
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=320145#320145
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|