Today's Message Index:
----------------------
1. 06:02 AM - Re: Step (AirMike)
2. 06:43 AM - Re: Step (Andy Turner)
3. 07:05 AM - Re: Re: Step (Werner Schneider)
4. 02:47 PM - Re: FS: Trutrack Pitch and Roll Servos (Patrick Pulis)
5. 06:47 PM - Re: Step (AirMike)
6. 06:55 PM - Re: N4959S is finally painted (builder 40214) (AirMike)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Attached is picture of the doubler plate for bolt access hole. the whole job took
about 4 hrs in all. Remember that the side panel fits here so check and fit
carefully. Note that the doubler is cut away. As I recall these are the same
pieces as the pitot access plate on the wing.
--------
See you OSH '11
Q/B - flying 1 yr+
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322658#322658
Attachments:
http://forums.matronics.com//files/p1000863_197.jpg
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I installed my access covers last night, and they look just like the ones in the
photos above. Only difference is that I put a bit of a joggle in the doubler
where it runs under the rib, but perhaps that isn't necessary.
--------
Andy Turner
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322665#322665
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
From what is looks they are the stall warning access parts VA-195C/D
see Section 19.
Werner
On 08.12.2010 14:59, AirMike wrote:
> --> RV10-List message posted by: "AirMike"<Mikeabel@Pacbell.net>
>
> Attached is picture of the doubler plate for bolt access hole. the whole job
took about 4 hrs in all. Remember that the side panel fits here so check and fit
carefully. Note that the doubler is cut away. As I recall these are the same
pieces as the pitot access plate on the wing.
>
> --------
> See you OSH '11
> Q/B - flying 1 yr+
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=322658#322658
>
>
> Attachments:
>
> http://forums.matronics.com//files/p1000863_197.jpg
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: FS: Trutrack Pitch and Roll Servos |
Jae, I'd be interested in the pitch servo if you are willing to split?=0A
=0AKind regards=0A=0APatrick Pulis=0AAdelaide, South Australia=0ARV-10 4029
9=0A=0A=0A=0A=0A________________________________=0AFrom: jchang10 <jc-matro
nics_rv10@jline.com>=0ATo: rv10-list@matronics.com=0ASent: Wed, 8 December,
2010 4:01:28 PM=0ASubject: RV10-List: FS: Trutrack Pitch and Roll Servos
com>=0A=0ALink to post on VAF with photo.=0Ahttp://www.vansairforce.com/com
munity/showthread.php?t=65281=0A=0AI have TruTrak servos for both roll an
d pitch for sale, which were originally to =0Abe paired with the Digiflight
IIVS head, eventually. Due to a change in plans, =0Athese servos are no lo
nger needed. The servos were mounted in the -10 project, =0Abut they have n
ot flown yet. The sale includes the original Trutrak box, foam =0Apackaging
, color print install "instructions" (basically just color prints) and =0Am
ounting hardware for the right wing and the pitch mount.=0A=0AI am asking $
1,970 or OBO, which includes shipping. Trutrak list is $2,250.=0A=0AThanks
for looking, and let me know if you have any questions. Thanks!=0AJae=0A#40
533=0A=0A=0A=0A=0ARead this topic online here:=0A=0Ahttp://forums.matronics
==============0A=0A=0A
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I think that you are correct and the plates are actually from the stall warn access
plate not the pitot access plate
--------
See you OSH '11
Q/B - flying 1 yr+
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322710#322710
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: N4959S is finally painted (builder 40214) |
When do I get my original design copyright royalty check ?
Another great paint job from Kracon......
--------
See you OSH '11
Q/B - flying 1 yr+
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322712#322712
Attachments:
http://forums.matronics.com//files/final_on_ramp_951.jpg
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|