---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 01/16/11: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:57 AM - Re: Rib Fluting Video (was Basic Fluting Question) (Billy & Tami Britton) 2. 11:27 AM - Re: Re: Control stick connector (George Nolin) 3. 04:32 PM - Re: Control stick connector (johngoodman) 4. 06:43 PM - Re: Re: Control stick connector (Pascal) 5. 07:04 PM - Wing Cradle (Strasnuts) 6. 08:32 PM - Re: Dimple Leading Edge (mouser) ________________________________ Message 1 _____________________________________ Time: 07:57:04 AM PST US From: "Billy & Tami Britton" Subject: Re: RV10-List: Rib Fluting Video (was Basic Fluting Question) Very informative video. Thanks. Bill -------------------------------------------------- From: "Jerry Calvert" Sent: Saturday, January 15, 2011 9:38 PM Subject: RE: RV10-List: Rib Fluting Video (was Basic Fluting Question) > > Here is an interesting video on Fluting RV12 ribs. > http://www.youtube.com/watch?v=jqNoVAQLo0M > > Jerry Calvert > RV6 > > -----Original Message----- > From: owner-rv10-list-server@matronics.com > [mailto:owner-rv10-list-server@matronics.com] On Behalf Of rv10flyer > Sent: Friday, January 14, 2011 10:58 PM > To: rv10-list@matronics.com > Subject: RV10-List: Re: Basic Fluting Question > > > I found lining up a flexible 24" steel rule with the hole edges to work > the > best. The edge distance always varies due to the holes being punched then > the rib forming. By lying them on a table you may get a straight > sheetmetal > edge but not a straight set of holes. The pre-punched skin holes are in a > straight line so you want to have the holes in the ribs in a straight line > not the edge of the metal flange. I just did a little at a time and if I > overdid it just went back and took some out. After a few ribs you know > just > how much force to use and where. > > -------- > Wayne Gillispie, A&P 5/93, PPC 10/08 > Bldr# 40983 SB Started 12/1/09. > Fuselage Sec 39 Control System. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=327073#327073 > > > ________________________________ Message 2 _____________________________________ Time: 11:27:34 AM PST US From: George Nolin Subject: Re: RV10-List: Re: Control stick connector I was able to get the blue cable into the tube by filing a little relief notch to make the 90 degree turn into a hole I drilled into the curved part of the stick. I'll get a picture that shows this better than words can describe. Hank Nolin = rv-10 Soon Sent from my iPad On Jan 15, 2011, at 8:16 PM, "rvdave" wrote: > > Has anyone drilled into the control sticks so the blue cable could go inside the stick instead of exterior? > > -------- > Dave Ford > RV6 flying > RV10 building > Cadillac, MI > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=327154#327154 > > > > > > > > > > ________________________________ Message 3 _____________________________________ Time: 04:32:55 PM PST US Subject: RV10-List: Re: Control stick connector From: "johngoodman" rvdave wrote: > Has anyone drilled into the control sticks so the blue cable could go inside the stick instead of exterior? I didn't bother. I used lacing to firmly attach it to the back of the stick, and then had Abby at Flightline Interiors make a "boot" for the stick in my upholstery color - looks fantastic. About eighty bucks and worth it. John -------- #40572 Painted and assembled. Panel almost ready. N711JG reserved Read this topic online here: http://forums.matronics.com/viewtopic.php?p=327227#327227 ________________________________ Message 4 _____________________________________ Time: 06:43:55 PM PST US From: "Pascal" Subject: Re: RV10-List: Re: Control stick connector I did, I put a 90 degree bend in the upper stick. pretty much followed Tim Olson's site for doing mine. Looks much cleaner to me, but it does take some work to make it come through the tube to the bottom. Not hard and looks much more mice than leaving it on with zip ties. A small boot off the bottom panel into the flightstick and painting the stick would be nice. I think I took this picture from Greg Hale's site. With that said, a full flightstick boot would cover the stick as well and look equally nice. Pascal -------------------------------------------------- From: "rvdave" Sent: Saturday, January 15, 2011 6:16 PM Subject: RV10-List: Re: Control stick connector > > Has anyone drilled into the control sticks so the blue cable could go > inside the stick instead of exterior? > > -------- > Dave Ford > RV6 flying > RV10 building > Cadillac, MI > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=327154#327154 > > > ________________________________ Message 5 _____________________________________ Time: 07:04:32 PM PST US Subject: RV10-List: Wing Cradle From: "Strasnuts" Anyone interested in a free wing cradle in SLC? Has four casters and carpet ready to use and holds both wings. -------- Cust. #40936 RV-10 SB Fuselage N801VR reserved Read this topic online here: http://forums.matronics.com/viewtopic.php?p=327246#327246 ________________________________ Message 6 _____________________________________ Time: 08:32:06 PM PST US Subject: RV10-List: Re: Dimple Leading Edge From: "mouser" I just did mine last week with the DRDT-2, the only holes I wasn't able to do were the two stall warning holes on the right wing. I did have to reverse the dies so that the skin bent down below the DRDT-2, and I needed a couple people to help support the skin while I maneuvered it around, but we knocked both skins out in under an hour on my lunch break. -------- RV-10 #40988 http://mouser.org/projects/rv-10/ KLAM Read this topic online here: http://forums.matronics.com/viewtopic.php?p=327250#327250 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.