Today's Message Index:
----------------------
1. 12:30 PM - Re: AHRS Mount angle (Bob Turner)
2. 12:35 PM - POS12 Flap Position Indicator Mounting (Les Kearney)
3. 06:51 PM - Re: POS12 Flap Position Indicator Mounting (Rob Kochman)
4. 10:14 PM - Section 46 - Engine Mount Question (Patrick Pulis)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: AHRS Mount angle |
Any real world input? I'd also like to know the answer.
The GRT instructions say to put the AHRS parallel to the longitudinal axis. But
there is also a software adjustment to move the vertical bars up/down, "...just
as in a conventional AI...". So I don't know how critical this is.
By my measurement (same location, a shelf built off the longitudinal aluminum angles
behind the battery) I will need to shim the forward end up by 0.15" for
every 7" of length, which is 1.2 degrees. Anyone else get or use these numbers?
--------
Bob Turner
RV-10 QB
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=328932#328932
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | POS12 Flap Position Indicator Mounting |
Mike
I mounted my POS12 a couple of days ago using your design. If is absolutely
brilliant in its simplicity.
Cheers
Les
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Michael Kraus
Sent: January-22-11 6:29 AM
Subject: Re: RV10-List: AFS AOA flap switch
Does this look familiar? :-)
On Jan 22, 2011, at 7:45 AM, Alan Mekler wrote:
Bob,
It wasn't my idea but I don't remember who on the forum came up with it.
Alan
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Bob Leffler
Sent: Saturday, January 22, 2011 7:22 AM
Subject: RE: RV10-List: AFS AOA flap switch
Alan,
I've not seen anyone mount the POS12 like you did. I like it!
bob
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Alan Mekler
Sent: Saturday, January 22, 2011 6:36 AM
Subject: RE: RV10-List: AFS AOA flap switch
John,
I have the Ray Allen POS12 flap sensor. It displays the flap position on the
AFS EFIS as well as gives the info to the AOA, It has nothing to do with the
flap switch which does not connect into the AFS EFIS.
Alan
_____
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of John Gonzalez
Sent: Saturday, January 22, 2011 12:47 AM
Subject: RV10-List: AFS AOA flap switch
I don't understand why I have a Ray Allen flap position sensor which doesn't
replace the flap switch for the AOA. Seems like a software issue which could
supercede the hardware issue.
Anyone have pictures of the AOA flap switch installed.
I have the Ray Allen flap sensor already completed.
Thanks
John
http://www.matronics.com/Navigator?RV10-List
http://forums.matronics.com <http://forums.matronics.com/>
http://www.matronics.com/contribution
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com
/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/c
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com
/Navigator?RV10-List
href="http://forums.matronics.com/">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/contri
bution
Michael Kraus
n223rv@wolflakeairport.net
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: POS12 Flap Position Indicator Mounting |
Wow, wish I'd seen that before I did mine. Very nice.
-Rob
On Sat, Jan 29, 2011 at 12:24 PM, Les Kearney <kearney@shaw.ca> wrote:
> Mike
>
> I mounted my POS12 a couple of days ago using your design. If is absolute
ly
> brilliant in its simplicity.
>
> Cheers
>
> Les
>
> ------------------------------
> *From:* owner-rv10-list-server@matronics.com [mailto:
> owner-rv10-list-server@matronics.com] *On Behalf Of *Michael Kraus
> *Sent:* January-22-11 6:29 AM
> *To:* rv10-list@matronics.com
> *Subject:* Re: RV10-List: AFS AOA flap switch
>
> Does this look familiar? :-)
>
>
> On Jan 22, 2011, at 7:45 AM, Alan Mekler wrote:
>
> Bob,
>
> It wasn=92t my idea but I don=92t remember who on the forum came up with
it.
>
> Alan
>
> ------------------------------
>
> *From:* owner-rv10-list-server@matronics.com [mailto:
> owner-rv10-list-server@matronics.com] *On Behalf Of *Bob Leffler
> *Sent:* Saturday, January 22, 2011 7:22 AM
> *To:* rv10-list@matronics.com
> *Subject:* RE: RV10-List: AFS AOA flap switch
>
> Alan,
>
> I=92ve not seen anyone mount the POS12 like you did. I like it!
>
> bob
>
> *From:* owner-rv10-list-server@matronics.com [mailto:
> owner-rv10-list-server@matronics.com] *On Behalf Of *Alan Mekler
> *Sent:* Saturday, January 22, 2011 6:36 AM
> *To:* rv10-list@matronics.com
> *Subject:* RE: RV10-List: AFS AOA flap switch
>
> John,
>
> I have the Ray Allen POS12 flap sensor. It displays the flap position on
> the AFS EFIS as well as gives the info to the AOA, It has nothing to do w
ith
> the flap switch which does not connect into the AFS EFIS.
>
> Alan
>
> ------------------------------
>
> *From:* owner-rv10-list-server@matronics.com [mailto:
> owner-rv10-list-server@matronics.com] *On Behalf Of *John Gonzalez
> *Sent:* Saturday, January 22, 2011 12:47 AM
> *To:* RV 10 group
> *Subject:* RV10-List: AFS AOA flap switch
>
> I don't understand why I have a Ray Allen flap position sensor which
> doesn't replace the flap switch for the AOA. Seems like a software issue
> which could supercede the hardware issue.
>
> Anyone have pictures of the AOA flap switch installed.
>
> I have the Ray Allen flap sensor already completed.
>
> Thanks
>
> John
>
> * *
>
> * *
>
> *http://www.matronics.com/Navigator?RV10-List*
>
> * *
>
> *http://forums.matronics.com*
>
> * *
>
> *http://www.matronics.com/contribution*
>
> * *
>
> *
>
> href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s.com/Navigator?RV10-List
> href="http://forums.matronics.com">http://forums.matronics.com
> href="http://www.matronics.com/contribution">http://www.matronics.com/c
*
>
> *
>
> href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic
s.com/Navigator?RV10-List
> href="http://forums.matronics.com/">http://forums.matronics.com
> href="http://www.matronics.com/contribution">http://www.matronics.com/c
ontribution
> *
>
>
> Michael Kraus
> n223rv@wolflakeairport.net
>
>
--
Rob Kochman
RV-10 "Finishing" Kit
Woodinville, WA (near Seattle)
http://kochman.net/N819K
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Section 46 - Engine Mount Question |
Hi there guys, I'm at the point of installing my engine mount as per Sectio
n 46, =0Apage 46-2 (Drawing Revision 1)-and I'd just like to clarify the
hole sizes and =0Ainstallation hardware for the engine mount please.--I
have amended my drawings =0Afrom Revision 0 to Revision 1, so i think that
I have the correct installation =0Adrawings for Section 46?=0A=0AThe instr
uctions indicate to drill a 3/8" hole in the Firewall Assembly common =0Ato
the WD-1001-D1 Dyna-1 Engine Mount, I did this.- The drawing also makes
=0Areference-to 6 x AN6-24 drilled bolts, which are used to attach the en
gine mount =0Ato the Firewall Assembly.=0A=0AIn my firewall forward kit I h
ave kit 'EA DYNA BOLT I(O)-540 Motor Mount Bolt =0AKit'-which appears to
correspond to the hardware required to attach the engine =0Amount.- This
kit contains the following hardware:=0A=0A4 x AN7-26 Drilled Bolt, 7/16"=0A
4 x AN310-7 Nut, Castle, 7/16"=0A8 x AN960 -716 Washer=0A4 x MS24665 -283 C
otter Pin=0A=0AThe above kit appears to be totally different from the hardw
are specified in the =0Adrawing, coupled with the fact that it is short 2 b
olts, 2 nuts, 4 washers and 2 =0Acotter pins and the diameter of the bolts
-are 7/16" instead of 3/8"?=0A=0AHave I missed a drawing revision guys?
=0A=0AI'm hoping that you might be able to clarify this for me as I'm a lit
tle =0Aconfused here.=0A=0AKind regards=0A=0A=0A=0APatrick Pulis=0ARV-10 #4
0299=0AAdelaide, South Australia=0A=0A=0A
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|