---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sat 01/29/11: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:30 PM - Re: AHRS Mount angle (Bob Turner) 2. 12:35 PM - POS12 Flap Position Indicator Mounting (Les Kearney) 3. 06:51 PM - Re: POS12 Flap Position Indicator Mounting (Rob Kochman) 4. 10:14 PM - Section 46 - Engine Mount Question (Patrick Pulis) ________________________________ Message 1 _____________________________________ Time: 12:30:44 PM PST US Subject: RV10-List: Re: AHRS Mount angle From: "Bob Turner" Any real world input? I'd also like to know the answer. The GRT instructions say to put the AHRS parallel to the longitudinal axis. But there is also a software adjustment to move the vertical bars up/down, "...just as in a conventional AI...". So I don't know how critical this is. By my measurement (same location, a shelf built off the longitudinal aluminum angles behind the battery) I will need to shim the forward end up by 0.15" for every 7" of length, which is 1.2 degrees. Anyone else get or use these numbers? -------- Bob Turner RV-10 QB Read this topic online here: http://forums.matronics.com/viewtopic.php?p=328932#328932 ________________________________ Message 2 _____________________________________ Time: 12:35:27 PM PST US From: "Les Kearney" Subject: RV10-List: POS12 Flap Position Indicator Mounting Mike I mounted my POS12 a couple of days ago using your design. If is absolutely brilliant in its simplicity. Cheers Les _____ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Michael Kraus Sent: January-22-11 6:29 AM Subject: Re: RV10-List: AFS AOA flap switch Does this look familiar? :-) On Jan 22, 2011, at 7:45 AM, Alan Mekler wrote: Bob, It wasn't my idea but I don't remember who on the forum came up with it. Alan _____ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Bob Leffler Sent: Saturday, January 22, 2011 7:22 AM Subject: RE: RV10-List: AFS AOA flap switch Alan, I've not seen anyone mount the POS12 like you did. I like it! bob From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Alan Mekler Sent: Saturday, January 22, 2011 6:36 AM Subject: RE: RV10-List: AFS AOA flap switch John, I have the Ray Allen POS12 flap sensor. It displays the flap position on the AFS EFIS as well as gives the info to the AOA, It has nothing to do with the flap switch which does not connect into the AFS EFIS. Alan _____ From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of John Gonzalez Sent: Saturday, January 22, 2011 12:47 AM Subject: RV10-List: AFS AOA flap switch I don't understand why I have a Ray Allen flap position sensor which doesn't replace the flap switch for the AOA. Seems like a software issue which could supercede the hardware issue. Anyone have pictures of the AOA flap switch installed. I have the Ray Allen flap sensor already completed. Thanks John http://www.matronics.com/Navigator?RV10-List http://forums.matronics.com http://www.matronics.com/contribution href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com /Navigator?RV10-List href="http://forums.matronics.com">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/c href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com /Navigator?RV10-List href="http://forums.matronics.com/">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/contri bution Michael Kraus n223rv@wolflakeairport.net ________________________________ Message 3 _____________________________________ Time: 06:51:25 PM PST US Subject: Re: RV10-List: POS12 Flap Position Indicator Mounting From: Rob Kochman Wow, wish I'd seen that before I did mine. Very nice. -Rob On Sat, Jan 29, 2011 at 12:24 PM, Les Kearney wrote: > Mike > > I mounted my POS12 a couple of days ago using your design. If is absolute ly > brilliant in its simplicity. > > Cheers > > Les > > ------------------------------ > *From:* owner-rv10-list-server@matronics.com [mailto: > owner-rv10-list-server@matronics.com] *On Behalf Of *Michael Kraus > *Sent:* January-22-11 6:29 AM > *To:* rv10-list@matronics.com > *Subject:* Re: RV10-List: AFS AOA flap switch > > Does this look familiar? :-) > > > On Jan 22, 2011, at 7:45 AM, Alan Mekler wrote: > > Bob, > > It wasn=92t my idea but I don=92t remember who on the forum came up with it. > > Alan > > ------------------------------ > > *From:* owner-rv10-list-server@matronics.com [mailto: > owner-rv10-list-server@matronics.com] *On Behalf Of *Bob Leffler > *Sent:* Saturday, January 22, 2011 7:22 AM > *To:* rv10-list@matronics.com > *Subject:* RE: RV10-List: AFS AOA flap switch > > Alan, > > I=92ve not seen anyone mount the POS12 like you did. I like it! > > bob > > *From:* owner-rv10-list-server@matronics.com [mailto: > owner-rv10-list-server@matronics.com] *On Behalf Of *Alan Mekler > *Sent:* Saturday, January 22, 2011 6:36 AM > *To:* rv10-list@matronics.com > *Subject:* RE: RV10-List: AFS AOA flap switch > > John, > > I have the Ray Allen POS12 flap sensor. It displays the flap position on > the AFS EFIS as well as gives the info to the AOA, It has nothing to do w ith > the flap switch which does not connect into the AFS EFIS. > > Alan > > ------------------------------ > > *From:* owner-rv10-list-server@matronics.com [mailto: > owner-rv10-list-server@matronics.com] *On Behalf Of *John Gonzalez > *Sent:* Saturday, January 22, 2011 12:47 AM > *To:* RV 10 group > *Subject:* RV10-List: AFS AOA flap switch > > I don't understand why I have a Ray Allen flap position sensor which > doesn't replace the flap switch for the AOA. Seems like a software issue > which could supercede the hardware issue. > > Anyone have pictures of the AOA flap switch installed. > > I have the Ray Allen flap sensor already completed. > > Thanks > > John > > * * > > * * > > *http://www.matronics.com/Navigator?RV10-List* > > * * > > *http://forums.matronics.com* > > * * > > *http://www.matronics.com/contribution* > > * * > > * > > href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic s.com/Navigator?RV10-List > href="http://forums.matronics.com">http://forums.matronics.com > href="http://www.matronics.com/contribution">http://www.matronics.com/c * > > * > > href="http://www.matronics.com/Navigator?RV10-List">http://www.matronic s.com/Navigator?RV10-List > href="http://forums.matronics.com/">http://forums.matronics.com > href="http://www.matronics.com/contribution">http://www.matronics.com/c ontribution > * > > > Michael Kraus > n223rv@wolflakeairport.net > > -- Rob Kochman RV-10 "Finishing" Kit Woodinville, WA (near Seattle) http://kochman.net/N819K ________________________________ Message 4 _____________________________________ Time: 10:14:15 PM PST US From: Patrick Pulis Subject: RV10-List: Section 46 - Engine Mount Question Hi there guys, I'm at the point of installing my engine mount as per Sectio n 46, =0Apage 46-2 (Drawing Revision 1)-and I'd just like to clarify the hole sizes and =0Ainstallation hardware for the engine mount please.--I have amended my drawings =0Afrom Revision 0 to Revision 1, so i think that I have the correct installation =0Adrawings for Section 46?=0A=0AThe instr uctions indicate to drill a 3/8" hole in the Firewall Assembly common =0Ato the WD-1001-D1 Dyna-1 Engine Mount, I did this.- The drawing also makes =0Areference-to 6 x AN6-24 drilled bolts, which are used to attach the en gine mount =0Ato the Firewall Assembly.=0A=0AIn my firewall forward kit I h ave kit 'EA DYNA BOLT I(O)-540 Motor Mount Bolt =0AKit'-which appears to correspond to the hardware required to attach the engine =0Amount.- This kit contains the following hardware:=0A=0A4 x AN7-26 Drilled Bolt, 7/16"=0A 4 x AN310-7 Nut, Castle, 7/16"=0A8 x AN960 -716 Washer=0A4 x MS24665 -283 C otter Pin=0A=0AThe above kit appears to be totally different from the hardw are specified in the =0Adrawing, coupled with the fact that it is short 2 b olts, 2 nuts, 4 washers and 2 =0Acotter pins and the diameter of the bolts -are 7/16" instead of 3/8"?=0A=0AHave I missed a drawing revision guys? =0A=0AI'm hoping that you might be able to clarify this for me as I'm a lit tle =0Aconfused here.=0A=0AKind regards=0A=0A=0A=0APatrick Pulis=0ARV-10 #4 0299=0AAdelaide, South Australia=0A=0A=0A ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.