Today's Message Index:
----------------------
1. 08:07 AM - Notice of my "hacked" email account (NormRainey@aol.com)
2. 10:05 AM - iPad (Albert Gardner)
3. 12:20 PM - Re: Chicago Area AN Hardware Source? (efdsteve@aol.com)
4. 12:44 PM - Baggage Door Opening Dimmensions (Shannon Hicks)
5. 02:04 PM - Re: Baggage Door Opening Dimmensions (Bill Watson)
6. 02:33 PM - Re: Baggage Door Opening Dimmensions (Shannon Hicks)
7. 04:12 PM - Re: Baggage Door Opening Dimmensions (Bill Watson)
8. 07:33 PM - Re: Baggage Door Opening Dimmensions (Lew Gallagher)
9. 08:07 PM - Re: Baggage Door Opening Dimmensions (Pascal)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Notice of my "hacked" email account |
Recently over the weekend my AOL email account was "hacked" and there have
been emails sent out bearing my name, but not originating from me. I
apologize for any confusion and I have reported this to the "fraud" department
at AOL and the local authorities for prosecution.
Norm
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I found that my bad Elf GPS unit doesn't always seem to pick up the satellites
so I got an extension cable so that the GPS can lay up on the glare shield (along
with the Garmin 496 GPS and WX pucks). I may have to start thinking about
external gps antennas although I'm going to try placing the Bad Elf up in the
overhead console next. Extension cable was 4.99 + 4.99 shipping from cellphoneshop.com
so not as expensive as I had imagined. I'm learning to love this iPad
and Foreflight.
Albert Gardner
N991RV
Yuma, AZ
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Chicago Area AN Hardware Source? |
Try Poplar Grove Airmotive Parts Department, just north of Belvidere at the
Poplar Grove Airport.
Steve Weinstock
Schaumburg, IL
40230, finishing
-----Original Message-----
From: Sean Stephens <sean@stephensville.com>
Sent: Sat, May 14, 2011 11:20 am
Subject: Re: RV10-List: Chicago Area AN Hardware Source?
That's not too bad. I'm 1/2 way between O'hare and Rockford on I-90.
o just a straight shot north a bit.
On 5/14/11 9:37 AM, David Leikam wrote:
--> RV10-List message posted by: David Leikam<daveleikam@wi.rr.com>
This might be a bit far for you but they are a good source.
http://www.pegasusautoracing.com/advcat.asp?CategoryID=HARDWARE
David Leikam
RV10
Flying
On May 14, 2011, at 9:19 AM, Sean Stephens wrote:
> --> RV10-List message posted by: Sean Stephens<sean@stephensville.com>
>
> Anyone around the Chicago western suburbs know of a source for AN Hardwar
e
ocally? I was spoiled when I was in Arizona. Had a shop a few minutes dri
ve
way. Aircraft Spruce usually gets stuff to me in a couple days, but there
I
imes when I just wanted to drive and pick it up same day.
>
> -Sean #40303
>
>
-= - The RV10-List Email Forum -
-= Use the Matronics List Features Navigator to browse
-= the many List utilities such as List Un/Subscription,
-= Archive Search & Download, 7-Day Browse, Chat, FAQ,
-= Photoshare, and much much more:
-
-= --> http://www.matronics.com/Navigator?RV10-List
-
-========================
-= - MATRONICS WEB FORUMS -
-= Same great content also available via the Web Forums!
-
-= --> http://forums.matronics.com
-
-========================
-= - List Contribution Web Site -
-= Thank you for your generous support!
-= -Matt Dralle, List Admin.
-= --> http://www.matronics.com/contribution
-========================
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Baggage Door Opening Dimmensions |
Would you guys mind pointing me in the direction of where I can get the
baggage door opening dimensions? I am about to order an article air cooler
for my Cherokee and want to make sure it will fit in the 10.
Thanks,
Shannon
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Baggage Door Opening Dimmensions |
It's an odd shaped opening. Rounded down to the nearest 1/4":
-The vertical at the front is 19.25"
- The horizontal at top is 20.25
- A diagonal of 28" from lower LH corner to upper right
- But then you have to remove a triangle at the lower bottom rear corner
that is 7" horizontally and 6" vertically
The whole affair looks like (I hope):
-------------------------
! !
! !
! !
! /
! /
--------------------/
Hope that helps.
Bill "re-installing the panel, looking for a hangar" Watson
On 5/16/2011 3:41 PM, Shannon Hicks wrote:
>
> Would you guys mind pointing me in the direction of where I can get
> the baggage door opening dimensions? I am about to order an article
> air cooler for my Cherokee and want to make sure it will fit in the 10.
>
> Thanks,
> Shannon
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Baggage Door Opening Dimmensions |
I think I understand... Does the attached drawing look about right?
On Mon, May 16, 2011 at 4:01 PM, Bill Watson <Mauledriver@nc.rr.com> wrote:
>
> It's an odd shaped opening. Rounded down to the nearest 1/4":
> -The vertical at the front is 19.25"
> - The horizontal at top is 20.25
> - A diagonal of 28" from lower LH corner to upper right
> - But then you have to remove a triangle at the lower bottom rear corner
> that is 7" horizontally and 6" vertically
> The whole affair looks like (I hope):
>
> -------------------------
> ! !
> ! !
> ! !
> ! /
> ! /
> --------------------/
>
> Hope that helps.
>
> Bill "re-installing the panel, looking for a hangar" Watson
>
>
> On 5/16/2011 3:41 PM, Shannon Hicks wrote:
>
>>
>> Would you guys mind pointing me in the direction of where I can get the
>> baggage door opening dimensions? I am about to order an article air cooler
>> for my Cherokee and want to make sure it will fit in the 10.
>>
>> Thanks,
>> Shannon
>>
>>
>
>
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Baggage Door Opening Dimmensions |
That's it!
It's a very satisfying piece to assemble because it has a slight
compound curve throughout it. Not sure how you would fabricate it
without CAD and CNC... at least without n years of sheet metal
experience... but it just clecos together and fits perfectly.
On 5/16/2011 5:28 PM, Shannon Hicks wrote:
> I think I understand... Does the attached drawing look about right?
>
> On Mon, May 16, 2011 at 4:01 PM, Bill Watson <Mauledriver@nc.rr.com
> <mailto:Mauledriver@nc.rr.com>> wrote:
>
> <Mauledriver@nc.rr.com <mailto:Mauledriver@nc.rr.com>>
>
> It's an odd shaped opening. Rounded down to the nearest 1/4":
> -The vertical at the front is 19.25"
> - The horizontal at top is 20.25
> - A diagonal of 28" from lower LH corner to upper right
> - But then you have to remove a triangle at the lower bottom rear
> corner that is 7" horizontally and 6" vertically
> The whole affair looks like (I hope):
>
> -------------------------
> ! !
> ! !
> ! !
> ! /
> ! /
> --------------------/
>
> Hope that helps.
>
> Bill "re-installing the panel, looking for a hangar" Watson
>
>
> On 5/16/2011 3:41 PM, Shannon Hicks wrote:
>
>
> Would you guys mind pointing me in the direction of where I
> can get the baggage door opening dimensions? I am about to
> order an article air cooler for my Cherokee and want to make
> sure it will fit in the 10.
>
> Thanks,
> Shannon
>
>
> ==========
> arget="_blank">http://www.matronics.com/Navigator?RV10-List
> ==========
> http://forums.matronics.com
> ==========
> le, List Admin.
> ="_blank">http://www.matronics.com/contribution
> ==========
>
>
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Baggage Door Opening Dimmensions |
Hey Shannon,
I've made my own cooler/ac for the baggage compartment in the -10. I'll
get dimensions of the cooler tomorrow -- it's about a perfect fit.
Later, - Lew
----- Original Message -----
From: Shannon Hicks
To: rv10-list@matronics.com
Sent: Monday, May 16, 2011 3:41 PM
Subject: RV10-List: Baggage Door Opening Dimmensions
Would you guys mind pointing me in the direction of where I can get
the baggage door opening dimensions? I am about to order an article air
cooler for my Cherokee and want to make sure it will fit in the 10.
Thanks,
Shannon
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Baggage Door Opening Dimmensions |
Is the article meant to be arctic air cooler? if so buy it from Lew, on
this list, or make it yourself. much less expensive.
I need to get around to making mine one of these days.
Pascal
From: Shannon Hicks
Sent: Monday, May 16, 2011 12:41 PM
Subject: RV10-List: Baggage Door Opening Dimmensions
Would you guys mind pointing me in the direction of where I can get the
baggage door opening dimensions? I am about to order an article air
cooler for my Cherokee and want to make sure it will fit in the 10.
Thanks,
Shannon
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|