Today's Message Index:
----------------------
1. 07:47 AM - Re: -10 Plans (fdombroski)
2. 01:37 PM - Drill recomendation (Roger Standley)
3. 02:03 PM - Re: Drill recomendation (Kelly McMullen)
4. 04:18 PM - Re: OSH Campsite available up front (Tim Olson)
5. 05:31 PM - RV10-List - Three Daily Passes for Airventure (Jim Combs)
6. 06:00 PM - Re: Drill recomendation (John Trollinger)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Please add me to the access list.
Thanks
Frank D
N10FD #40090
--------
Frank Dombroski
RV-10 N10FD Flying
RV-8 N84FD Finished and sold :-{
N40 Sky Manor Airport NJ
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=347663#347663
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Drill recomendation |
I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the
location, I would rather drill out the screw than replace the nut plate.
The problem is that my drills aren't doing the job. Does anyone have a
recommendation on drills that will cut out the AN507-6R6 screw?
Roger
40291 flying
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Drill recomendation |
Consider drilling out the nut plate and replacing it with a ClickBond
nutplate. Getting a bunged screw out of a nut plate is a challenge,
especially with a small screw like that. If possible have someone pick
up a demo kit from Click Bond at OSH. Or a packet of adhesive plus a
nutplate or two can be had from the Flight Shop for under $10. BTW,
for most Click Bond nut plates you can use the same one for dimpled or
flat install, there is enough offset in the nut portion for the
countersink.
It would take a very sharp drill bit to get a good clean hole in the
screw with a very good easy out to get that screw to budge. If the
easy out broke, you would be down to changing the nut plate anyway.
On Mon, Jul 25, 2011 at 1:33 PM, Roger Standley <taildragon@msn.com> wrote:
> I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the
> location, I would rather drill out the screw than replace the nut plate. The
> problem is that my drills aren't doing the job. Does anyone have a
> recommendation on drills that will cut out the AN507-6R6 screw?
>
> Roger
> 40291 flying
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: OSH Campsite available up front |
The site is now taken.
Tim
On Jul 24, 2011, at 5:13 PM, Tim Olson <Tim@myrv10.com> wrote:
>
> No takers....Sean says 50% off.
> No takers yet.
> Tim
>
>
>
> On Jul 23, 2011, at 3:36 PM, Tim Olson <Tim@myrv10.com> wrote:
>
>>
>> Scott and I and Group are all here and I staked off one more site than we needed
up here at 57/58th and Lindbergh. Sean paid $374 for it and it's a good
sized site.
>>
>> First RV10 guy that wants it can have it for Sean's same cost. Its only maybe
200-300 yards from the entry gate.
>>
>> Email me at Timcell at myrv10 dot com to take it.
>> Tim
>>
>>
>>
>>
>>
>>
>
>
>
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV10-List - Three Daily Passes for Airventure |
I have three days worth of prepaid daily passes from a friend who cannot
attend.
Not at all sure if they are even transferrable since they have a name
printed on them.
I will be arriving tomorrow (Tuesday) via VFR RV-10.
I will be leaving on Friday.
Contact me off-line (E-Mail) - Price is negotiable (or even free!)
We can work hour arrangements to get them to you at Air Venture
Jim Combs
N312F - Flying 250 hours
JimInLexKy@GMail.com
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Drill recomendation |
I just have a craftsman screw removal kit, I have used it many a times
on the 6r6 screws..
On Mon, Jul 25, 2011 at 4:33 PM, Roger Standley <taildragon@msn.com> wrote:
> I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the
> location, I would rather drill out the screw than replace the nut plate. The
> problem is that my drills aren't doing the job. Does anyone have a
> recommendation on drills that will cut out the AN507-6R6 screw?
>
> Roger
> 40291 flying
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|