---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Mon 07/25/11: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:47 AM - Re: -10 Plans (fdombroski) 2. 01:37 PM - Drill recomendation (Roger Standley) 3. 02:03 PM - Re: Drill recomendation (Kelly McMullen) 4. 04:18 PM - Re: OSH Campsite available up front (Tim Olson) 5. 05:31 PM - RV10-List - Three Daily Passes for Airventure (Jim Combs) 6. 06:00 PM - Re: Drill recomendation (John Trollinger) ________________________________ Message 1 _____________________________________ Time: 07:47:41 AM PST US Subject: RV10-List: Re: -10 Plans From: "fdombroski" Please add me to the access list. Thanks Frank D N10FD #40090 -------- Frank Dombroski RV-10 N10FD Flying RV-8 N84FD Finished and sold :-{ N40 Sky Manor Airport NJ Read this topic online here: http://forums.matronics.com/viewtopic.php?p=347663#347663 ________________________________ Message 2 _____________________________________ Time: 01:37:13 PM PST US From: "Roger Standley" Subject: RV10-List: Drill recomendation I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the location, I would rather drill out the screw than replace the nut plate. The problem is that my drills aren't doing the job. Does anyone have a recommendation on drills that will cut out the AN507-6R6 screw? Roger 40291 flying ________________________________ Message 3 _____________________________________ Time: 02:03:46 PM PST US Subject: Re: RV10-List: Drill recomendation From: Kelly McMullen Consider drilling out the nut plate and replacing it with a ClickBond nutplate. Getting a bunged screw out of a nut plate is a challenge, especially with a small screw like that. If possible have someone pick up a demo kit from Click Bond at OSH. Or a packet of adhesive plus a nutplate or two can be had from the Flight Shop for under $10. BTW, for most Click Bond nut plates you can use the same one for dimpled or flat install, there is enough offset in the nut portion for the countersink. It would take a very sharp drill bit to get a good clean hole in the screw with a very good easy out to get that screw to budge. If the easy out broke, you would be down to changing the nut plate anyway. On Mon, Jul 25, 2011 at 1:33 PM, Roger Standley wrote: > I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the > location, I would rather drill out the screw than replace the nut plate. The > problem is that my drills aren't doing the job. Does anyone have a > recommendation on drills that will cut out the AN507-6R6 screw? > > Roger > 40291 flying > > ________________________________ Message 4 _____________________________________ Time: 04:18:19 PM PST US From: Tim Olson Subject: Re: RV10-List: OSH Campsite available up front The site is now taken. Tim On Jul 24, 2011, at 5:13 PM, Tim Olson wrote: > > No takers....Sean says 50% off. > No takers yet. > Tim > > > > On Jul 23, 2011, at 3:36 PM, Tim Olson wrote: > >> >> Scott and I and Group are all here and I staked off one more site than we needed up here at 57/58th and Lindbergh. Sean paid $374 for it and it's a good sized site. >> >> First RV10 guy that wants it can have it for Sean's same cost. Its only maybe 200-300 yards from the entry gate. >> >> Email me at Timcell at myrv10 dot com to take it. >> Tim >> >> >> >> >> >> > > > > ________________________________ Message 5 _____________________________________ Time: 05:31:12 PM PST US Subject: RV10-List: RV10-List - Three Daily Passes for Airventure From: Jim Combs I have three days worth of prepaid daily passes from a friend who cannot attend. Not at all sure if they are even transferrable since they have a name printed on them. I will be arriving tomorrow (Tuesday) via VFR RV-10. I will be leaving on Friday. Contact me off-line (E-Mail) - Price is negotiable (or even free!) We can work hour arrangements to get them to you at Air Venture Jim Combs N312F - Flying 250 hours JimInLexKy@GMail.com ________________________________ Message 6 _____________________________________ Time: 06:00:09 PM PST US Subject: Re: RV10-List: Drill recomendation From: John Trollinger I just have a craftsman screw removal kit, I have used it many a times on the 6r6 screws.. On Mon, Jul 25, 2011 at 4:33 PM, Roger Standley wrote: > I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the > location, I would rather drill out the screw than replace the nut plate. The > problem is that my drills aren't doing the job. Does anyone have a > recommendation on drills that will cut out the AN507-6R6 screw? > > Roger > 40291 flying > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.