Today's Message Index:
----------------------
1. 11:32 AM - Wing Kit (mds4878)
2. 11:48 AM - Re: Drill recomendation (Roger Standley)
3. 04:24 PM - Re: RV-10's in HBP at OSH (Thane States)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Getting ready to buy my wing kit.
Does anybody have a wing kit for sale?
Started or not started that would save me money buying.
--------
RV-10 #40447
Fuselage almost done.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=347777#347777
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Drill recomendation |
Thanks for the info=2C guys. I will give it a try.
> Date: Mon=2C 25 Jul 2011 20:57:30 -0400
> Subject: Re: RV10-List: Drill recomendation
> From: john@trollingers.com
> To: rv10-list@matronics.com
>
>
> I just have a craftsman screw removal kit=2C I have used it many a times
> on the 6r6 screws..
>
> On Mon=2C Jul 25=2C 2011 at 4:33 PM=2C Roger Standley <taildragon@msn.com
> wrote:
> > I broke off an AN507-6R6 screw in a K1100-06 nut plate. Because of the
> > location=2C I would rather drill out the screw than replace the nut pla
te. The
> > problem is that my drills aren't doing the job. Does anyone have a
> > recommendation on drills that will cut out the AN507-6R6 screw?
> >
> > Roger
> > 40291 flying
> >
> >
> >
>
===========
===========
===========
===========
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: RV-10's in HBP at OSH |
Just got back after 2 nights at OSH. It was great to see so many fine
looking RV-10's. I think I was the only one to not be painted, but with a
little luck, I am of to the paint shop in the next week.
Just a few performance #'s for those building. We managed to go non
stop from KOSH to KUZA; 641 n.m. in 3 hrs. 41 mins. We started out with
30kts off the tail at 11,500. Running WOT. 20" mp. and 2330 rpm. 10 gph.
165 TAS.
That is a personal best for longest flight in the 10. My bladder is
most often the limiting factor. Once agian I cant say enough good about the
performance and utility of this airplane.
Safe flight to all going and returning from KOSH.
Thane
192 Hrs.
From: "Tim Olson" <Tim@myrv10.com>
Sent: Sunday, July 24, 2011 12:28 PM
Subject: RV10-List: RV-10's in HBP at OSH
> We're up to 13 now on Sunday a.m.
> Should be a great week!
>
>
--------------------------------------------------------------------------------
>
>
> <pre><b><font size=2 color="#000000" face="courier new,courier">
>
> href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List</a>
> href="http://forums.matronics.com">http://forums.matronics.com</a>
> href="http://www.matronics.com/contribution">http://www.matronics.com/contribution</a>
>
> </b></font></pre>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|