Today's Message Index:
----------------------
1. 03:34 PM - #4 Screw pop rivet dimpler (Billy & Tami Britton)
2. 04:29 PM - Re: #4 Screw pop rivet dimpler (Michael Kraus)
3. 04:31 PM - Re: #4 Screw pop rivet dimpler (Dave Saylor)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | #4 Screw pop rivet dimpler |
I've bought an AFS AOA kit for installing into the wings on my -10. I
don't have the kit yet but I was informed through a PM that I will need
a #4 screw pop rivet dimpler. I've looked at both Avery and Cleveland
tools websites and don't see such a thing listed. Where can I find
this at? Can anyone who has installed the AOA kit please let me know
if I truly need this or is there another way of dimpling the screw
holes. Also, Is there any more need for a #4 screw pop rivet dimpler
on the rest of the airframe? If not, maybe someone would let me borrow
one (I'd cover shipping--unless it's just cheaper/easier to buy one).
Thanks in advance again,
Bill
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: #4 Screw pop rivet dimpler |
Try a 1/8" #30 dimpler. I'm pretty sure it's about the correct size....
Sent from my iPhone
On Feb 24, 2012, at 6:31 PM, "Billy & Tami Britton" <william@gbta.net> wrote
:
> I've bought an AFS AOA kit for installing into the wings on my -10. I don
't have the kit yet but I was informed through a PM that I will need a #4 sc
rew pop rivet dimpler. I've looked at both Avery and Cleveland tools websit
es and don't see such a thing listed. Where can I find this at? Can anyo
ne who has installed the AOA kit please let me know if I truly need this or i
s there another way of dimpling the screw holes. Also, Is there any more ne
ed for a #4 screw pop rivet dimpler on the rest of the airframe? If not, m
aybe someone would let me borrow one (I'd cover shipping--unless it's just c
heaper/easier to buy one).
>
> Thanks in advance again,
>
> Bill
>
>
>
==========================
=========
==========================
=========
==========================
=========
==========================
=========
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: #4 Screw pop rivet dimpler |
Bill,
A #4 screw is really close to a -4 flush rivet. You could mount a
dimple die in some sort of holder (like a bucking bar with a 1/8" hole
drilled in it) and put a very short rivet or screw through the skin
then drive it down gently with a flat set.
--Dave Saylor
On Fri, Feb 24, 2012 at 3:31 PM, Billy & Tami Britton <william@gbta.net> wrote:
> I've bought an AFS AOA kit for installing into the wings on my -10. I don't
> have the kit yet but I was informed through a PM that I will need a #4 screw
> pop rivet dimpler. I've looked at both Avery and Cleveland tools websites
> and don't see such a thing listed. Where can I find this at? Can anyone
> who has installed the AOA kit please let me know if I truly need this or is
> there another way of dimpling the screw holes. Also, Is there any more need
> for a #4 screw pop rivet dimpler on the rest of the airframe? If not,
> maybe someone would let me borrow one (I'd cover shipping--unless it's just
> cheaper/easier to buy one).
>
> Thanks in advance again,
>
> Bill
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|