Today's Message Index:
----------------------
1. 02:09 PM - MT 860 Governor (maca2790)
2. 02:47 PM - Re: MT 860 Governor (Michael Kraus)
3. 08:05 PM - Re: MT 860 Governor (Bill Watson)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hi all,
To get the Prop Governor to work with the Vans Baffle and cable mounting arrangement
I will have to move the stop plate and the control arm.
Has anyone else done this with their MT Governor?
Cheers
John MacCallum
VH-DUU
41016
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=371520#371520
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: MT 860 Governor |
Read the directions! There is a right way, and wrong way to do it. If i recall
correctly, basically loosen up the 6 safety wired screws and the assembly rotates.
I would be sure to read the instructions though....
Sent from my iPhone
On Apr 22, 2012, at 5:07 PM, "maca2790" <vk2gcn@cirruscomms.com.au> wrote:
>
> Hi all,
> To get the Prop Governor to work with the Vans Baffle and cable mounting arrangement
I will have to move the stop plate and the control arm.
>
> Has anyone else done this with their MT Governor?
>
> Cheers
>
> John MacCallum
> VH-DUU
> 41016
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=371520#371520
>
>
>
>
>
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: MT 860 Governor |
Exactly. I did it, no problems following the very specific directions.
Bill
Sent from my iPad
On Apr 22, 2012, at 5:44 PM, Michael Kraus <n223rv@wolflakeairport.net> wrote:
>
> Read the directions! There is a right way, and wrong way to do it. If i recall
correctly, basically loosen up the 6 safety wired screws and the assembly
rotates. I would be sure to read the instructions though....
>
> Sent from my iPhone
>
> On Apr 22, 2012, at 5:07 PM, "maca2790" <vk2gcn@cirruscomms.com.au> wrote:
>
>>
>> Hi all,
>> To get the Prop Governor to work with the Vans Baffle and cable mounting arrangement
I will have to move the stop plate and the control arm.
>>
>> Has anyone else done this with their MT Governor?
>>
>> Cheers
>>
>> John MacCallum
>> VH-DUU
>> 41016
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=371520#371520
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|