---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Wed 06/20/12: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 10:31 AM - Good signature (Robin Marks) 2. 02:03 PM - MGL equipment (Linn Walters) 3. 02:30 PM - Labels (Michael Sausen) 4. 05:33 PM - Re: Labels (Bob Turner) 5. 05:34 PM - Re: Skybolt Fasteners - Installation (Lew Gallagher) 6. 06:43 PM - Cleaning up Royco 782 (Phillip Perry) 7. 07:08 PM - Re: Cleaning up Royco 782 (Kelly McMullen) 8. 08:31 PM - Re: Good signature (Seano) 9. 09:57 PM - Re: Labels (Robin Marks) ________________________________ Message 1 _____________________________________ Time: 10:31:48 AM PST US From: Robin Marks Subject: RV10-List: Good signature I copied this off the European Yahoo RV list: Man is the best computer we can put aboard a spacecraft, and the only one that can be mass produced with unskilled labor. -- Wernher von Braun Robin Do Not Archive ________________________________ Message 2 _____________________________________ Time: 02:03:55 PM PST US From: Linn Walters Subject: RV10-List: MGL equipment Anyone have a flying RV-10 with MGL glass panels in it??? Linn .... still building ________________________________ Message 3 _____________________________________ Time: 02:30:35 PM PST US From: Michael Sausen Subject: RV10-List: Labels Does anyone have any label or graphics files for panel labels that could be reused as a starting point? I hate to reinvent the wheel. Michael ________________________________ Message 4 _____________________________________ Time: 05:33:46 PM PST US Subject: RV10-List: Re: Labels From: "Bob Turner" Attached is a MS Word file that I sent to Stein; he converted it to a nice sheet of decals (dip in water, slide off). -------- Bob Turner RV-10 QB Read this topic online here: http://forums.matronics.com/viewtopic.php?p=376174#376174 Attachments: http://forums.matronics.com//files/turner_labels_243.doc ________________________________ Message 5 _____________________________________ Time: 05:34:55 PM PST US Subject: RV10-List: Re: Skybolt Fasteners - Installation From: "Lew Gallagher" I just had an email inquiring about my comment on installing the solid flange around the firewall being easier than using the "ears" supplied with the new skybolt kits. I briefly read it in my email screener, then inadvertently deleted it. So here's hoping you get this as a general post. Yes, you just rivet it around the firewall, then when your cowl is fit, simply measure where you want to put the skybolts and pilot drill through the cowl and flange -- perfect fit. Originally I think everybody had to install their own flange (the kit was just male/female fasteners,collars, retaining rings), some scalloped it out, others didn't -- your preference for weight, easier to bend to fit if scalloped, etc. See Tim's site for pictures, specs on the aluminum, where to order it. The ears work OK, but personally, I don't see them as an improvement. I hope this addressed your inquiry, if not, send it again or post it here for other feedback. Later, - Lew -------- non-pilot crazy about building NOW OFICIALLY BUILDER #40549 Fly off completed ! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=376175#376175 ________________________________ Message 6 _____________________________________ Time: 06:43:37 PM PST US Subject: RV10-List: Cleaning up Royco 782 From: Phillip Perry I just shot some 782 into the lines and the brakes are officially good to go. I found one leak in the tunnel and would like to clean it up before things get corroded. Is there something out there that cuts it so I can flush the area where the leak was found? Phil ________________________________ Message 7 _____________________________________ Time: 07:08:13 PM PST US From: Kelly McMullen Subject: Re: RV10-List: Cleaning up Royco 782 It is petroleum product. Stoddard solvent or mineral spirits should take care of it. It should not be at all corrosive, but might be a dirt magnet. On 6/20/2012 6:42 PM, Phillip Perry wrote: > I just shot some 782 into the lines and the brakes are officially good > to go. I found one leak in the tunnel and would like to clean it up > before things get corroded. > > Is there something out there that cuts it so I can flush the area > where the leak was found? > > Phil > > * > > > * ----- No virus found in this message. Checked by AVG - www.avg.com ________________________________ Message 8 _____________________________________ Time: 08:31:26 PM PST US From: "Seano" Subject: Re: RV10-List: Good signature And all this time I thought I was skilled... ----- Original Message ----- From: Robin Marks To: rv10-list@matronics.com ; rv-list@matronics.com Sent: Wednesday, June 20, 2012 11:30 AM Subject: RV10-List: Good signature I copied this off the European Yahoo RV list: Man is the best computer we can put aboard a spacecraft, and the only one that can be mass produced with unskilled labor. -- Wernher von Braun Robin Do Not Archive ________________________________ Message 9 _____________________________________ Time: 09:57:26 PM PST US From: Robin Marks Subject: Re: RV10-List: Labels Seems like the labels would be so specific to your build that I can't see much benefit to prior work product. That being said Steins labels are a great way to go. Ideally use a vector based program like Illustrator for razor sharp results. Also consider color coding for quicker recognition. In my case red is fuel and heat (boost pump, pitot & cabin heat...), Blue for EFIS and O2, black for common items like lights. Both my 10 and 8 have engraved switches so labeling is bare minimum. Robin Sent from the new iPad On Jun 20, 2012, at 5:38 PM, "Michael Sausen" wrote: > > Does anyone have any label or graphics files for panel labels that could be reused as a starting point? I hate to reinvent the wheel. > > Michael > > > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.