Today's Message Index:
----------------------
1. 04:50 AM - Re: Builders Incentive (Patrick Pulis)
2. 02:06 PM - Looking for heated pitot screws (hotwheels)
3. 03:06 PM - Re: Looking for heated pitot screws (Bob)
4. 03:41 PM - Re: Builders Incentive (Ed Kranz)
5. 04:11 PM - Re: Looking for heated pitot screws (Dave Saylor)
6. 11:09 PM - A/C install gotcha (woxofswa)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Builders Incentive |
Gorgeous. Well done.
Warm regards
Patrick
On 24/06/2012, at 2:30 PM, Michael Kraus <n223rv@wolflakeairport.net> wrote:
> Just out of paint!
>
> <image.jpeg>
>
> -Mike Kraus
> Sent from my iPhone
> <pre><b><font size=2 color="#000000" face="courier new,courier">
>
>
> </b></font></pre>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Looking for heated pitot screws |
I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box today and
noticed that it has four screw holes (-4?), but no screws. There's nothing
special about this pitot... I think I bought it at ACS several years ago. Has
anyone else had this issue and if so where did you find screws?
http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php
Thanks,
Jay
N433RV - finishing up
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=376510#376510
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking for heated pitot screws |
Jay,
I've got a set you can borrow if if's time critical. You can track down a set and
get them back to me.
Bob
Sent from my iPhone
On Jun 24, 2012, at 4:03 PM, "hotwheels" <jaybrinkmeyer@yahoo.com> wrote:
>
> I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box today
and noticed that it has four screw holes (-4?), but no screws. There's nothing
special about this pitot... I think I bought it at ACS several years ago. Has
anyone else had this issue and if so where did you find screws?
>
> http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php
>
> Thanks,
> Jay
> N433RV - finishing up
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=376510#376510
>
>
>
>
>
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Builders Incentive |
Great, clean design, and I'm diggin' the checkered rudder!
On Sun, Jun 24, 2012 at 6:52 AM, Patrick Pulis <rv10free2fly@yahoo.com.au>wrote:
>
> Gorgeous. Well done.
>
> Warm regards
>
> Patrick
>
> On 24/06/2012, at 2:30 PM, Michael Kraus <n223rv@wolflakeairport.net>
> wrote:
>
> > Just out of paint!
> >
> > <image.jpeg>
> >
> > -Mike Kraus
> > Sent from my iPhone
> > <pre><b><font size=2 color="#000000" face="courier new,courier">
> >
> >
> > </b></font></pre>
>
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking for heated pitot screws |
We just went through tracking those down. They're a little odd, 6-40
thread pitch. We bought a whole box to get 4, send me your address and
I'll send you some.
Dave Saylor
831-750-0284 CL
On Sun, Jun 24, 2012 at 2:03 PM, hotwheels <jaybrinkmeyer@yahoo.com> wrote:
>
> I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box
> today and noticed that it has four screw holes (-4?), but no screws.
> There's nothing special about this pitot... I think I bought it at ACS
> several years ago. Has anyone else had this issue and if so where did you
> find screws?
>
> http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php
>
> Thanks,
> Jay
> N433RV - finishing up
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=376510#376510
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | A/C install gotcha |
If you are planning on installing engine driven air conditioning and you are using
an IO540 other than factory new, be careful to make sure that the pad for
the compressor mounting bracket has the four mount holes, even better if it has
studs. Not all do as we found out the hard way.
It isn't the end of the world if it doesn't. If you are having a core build-up
they can machine the holes at the shop, but if it slips by that step, (as mine
did), the holes will then have to be drilled in the field from a jig that is
available.
According to Airflow Performance, two of us found ourselves in this pickle just
this week.
--------
Myron Nelson
Mesa, AZ
Emp completed, QB wings completed, legacy build fuse in mostly done, finishing
kit in progress.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=376537#376537
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|