---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 06/24/12: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:50 AM - Re: Builders Incentive (Patrick Pulis) 2. 02:06 PM - Looking for heated pitot screws (hotwheels) 3. 03:06 PM - Re: Looking for heated pitot screws (Bob) 4. 03:41 PM - Re: Builders Incentive (Ed Kranz) 5. 04:11 PM - Re: Looking for heated pitot screws (Dave Saylor) 6. 11:09 PM - A/C install gotcha (woxofswa) ________________________________ Message 1 _____________________________________ Time: 04:50:13 AM PST US Subject: Re: RV10-List: Builders Incentive From: Patrick Pulis Gorgeous. Well done. Warm regards Patrick On 24/06/2012, at 2:30 PM, Michael Kraus wrote: > Just out of paint! > > > > -Mike Kraus > Sent from my iPhone > 

> 
> 
>
________________________________ Message 2 _____________________________________ Time: 02:06:42 PM PST US Subject: RV10-List: Looking for heated pitot screws From: "hotwheels" I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box today and noticed that it has four screw holes (-4?), but no screws. There's nothing special about this pitot... I think I bought it at ACS several years ago. Has anyone else had this issue and if so where did you find screws? http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php Thanks, Jay N433RV - finishing up Read this topic online here: http://forums.matronics.com/viewtopic.php?p=376510#376510 ________________________________ Message 3 _____________________________________ Time: 03:06:51 PM PST US Subject: Re: RV10-List: Looking for heated pitot screws From: Bob Jay, I've got a set you can borrow if if's time critical. You can track down a set and get them back to me. Bob Sent from my iPhone On Jun 24, 2012, at 4:03 PM, "hotwheels" wrote: > > I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box today and noticed that it has four screw holes (-4?), but no screws. There's nothing special about this pitot... I think I bought it at ACS several years ago. Has anyone else had this issue and if so where did you find screws? > > http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php > > Thanks, > Jay > N433RV - finishing up > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=376510#376510 > > > > > > > > > > ________________________________ Message 4 _____________________________________ Time: 03:41:39 PM PST US Subject: Re: RV10-List: Builders Incentive From: Ed Kranz Great, clean design, and I'm diggin' the checkered rudder! On Sun, Jun 24, 2012 at 6:52 AM, Patrick Pulis wrote: > > Gorgeous. Well done. > > Warm regards > > Patrick > > On 24/06/2012, at 2:30 PM, Michael Kraus > wrote: > > > Just out of paint! > > > > > > > > -Mike Kraus > > Sent from my iPhone > > 

> >
> >
> >
> > ________________________________ Message 5 _____________________________________ Time: 04:11:48 PM PST US From: Dave Saylor Subject: Re: RV10-List: Looking for heated pitot screws We just went through tracking those down. They're a little odd, 6-40 thread pitch. We bought a whole box to get 4, send me your address and I'll send you some. Dave Saylor 831-750-0284 CL On Sun, Jun 24, 2012 at 2:03 PM, hotwheels wrote: > > I pulled my brand new 12-AN5812 Falcon Heated Pitot tube out of the box > today and noticed that it has four screw holes (-4?), but no screws. > There's nothing special about this pitot... I think I bought it at ACS > several years ago. Has anyone else had this issue and if so where did you > find screws? > > http://www.aircraftspruce.com/catalog/inpages/12an5812_1.php > > Thanks, > Jay > N433RV - finishing up > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=376510#376510 > > ________________________________ Message 6 _____________________________________ Time: 11:09:43 PM PST US Subject: RV10-List: A/C install gotcha From: "woxofswa" If you are planning on installing engine driven air conditioning and you are using an IO540 other than factory new, be careful to make sure that the pad for the compressor mounting bracket has the four mount holes, even better if it has studs. Not all do as we found out the hard way. It isn't the end of the world if it doesn't. If you are having a core build-up they can machine the holes at the shop, but if it slips by that step, (as mine did), the holes will then have to be drilled in the field from a jig that is available. According to Airflow Performance, two of us found ourselves in this pickle just this week. -------- Myron Nelson Mesa, AZ Emp completed, QB wings completed, legacy build fuse in mostly done, finishing kit in progress. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=376537#376537 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.