Today's Message Index:
----------------------
 
     1. 07:28 PM - roll servo stop bracket (Rick Lark)
     2. 08:24 PM - Re: roll servo stop bracket (davidsoutpost@comcast.net)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
07:28:24 PM PST US
Subject: 
roll servo stop bracket
From: 
Rick Lark <larkrv10@gmail.com>
      
      Hi all
      
      I installed the roll servo today and found the 2 little 6-32 x 1/4" screws
      that fasten the stop bracket woefully short.  I got almost 1 1/2 turns on
      them.  Searching the archives revealed a couple of posts but no definitive
      conclusion.  Did anyone substitute the screws for something a little bit
      longer?  I know using a screw that's too long screw can cause interference
      internally.  I'm tempted to remove the lock washer, use a little bit of
      lock tite or use both.
      
      Anyone have a better solution?
      
      Thx
      
      Rick
      #40956
      Southampton, Ont
      FWF and Finish kit arrive tomorrow
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:24:28 PM PST US
From: 
davidsoutpost@comcast.net
Subject: 
Re: roll servo stop bracket
      
      I did just that: Removed the washer and used Loctite. 
      
      
      David Clifford 
      
      RV-10 Builder 
      Howell, MI 
      
      ----- Original Message -----
      From: "Rick Lark" <larkrv10@gmail.com> 
      Sent: Wednesday, November 7, 2012 10:27:30 PM 
      Subject: RV10-List: roll servo stop bracket 
      
      
      Hi all 
      
      I installed the roll servo today and found the 2 little 6-32 x 1/4" screws that
      fasten the stop bracket woefully short. I got almost 1 1/2 turns on them. Searching
      the archives revealed a couple of posts but no definitive conclusion. Did
      anyone substitute the screws for something a little bit longer? I know using
      a screw that's too long screw can cause interference internally. I'm tempted
      to remove the lock washer, use a little bit of lock tite or use both. 
      
      Anyone have a better solution? 
      
      Thx 
      
      Rick 
      #40956 
      Southampton, Ont 
      FWF and Finish kit arrive tomorrow 
      








Other Matronics Email List Services




Post A New Message
  
rv10-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV10-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rv10-list
Browse RV10-List Digests
  
http://www.matronics.com/digest/rv10-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --