---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Fri 11/30/12: 14 ---------------------------------------------------------- Today's Message Index: ---------------------- 0. 09:07 AM - [Please Read] - Last Official Day of List Fund Raiser! (Matt Dralle) 1. 11:17 AM - Rear Baffle Positioning Tips? (Sean Stephens) 2. 11:36 AM - Re: Rear Baffle Positioning Tips? (Michael Kraus) 3. 12:19 PM - Re: Rear Baffle Positioning Tips? (Kelly McMullen) 4. 12:19 PM - Re: Rear Baffle Positioning Tips? (Bob Leffler) 5. 12:20 PM - Re: Rear Baffle Positioning Tips? (davidsoutpost@comcast.net) 6. 01:03 PM - Re: Rear Baffle Positioning Tips? (Sean Stephens) 7. 01:25 PM - Re: Rear Baffle Positioning Tips? (Sean Stephens) 8. 01:29 PM - Re: Rear Baffle Positioning Tips? (Jae Chang) 9. 01:31 PM - Re: Rear Baffle Positioning Tips? (mdaniell) 10. 02:26 PM - Re: Re: Rear Baffle Positioning Tips? (Sean Stephens) 11. 02:42 PM - Re: Re: Rear Baffle Positioning Tips? (Rene Felker) 12. 04:25 PM - Re: Rear Baffle Positioning Tips? (bill.peyton) 13. 06:03 PM - Re: Re: Rear Baffle Positioning Tips? (Kelly McMullen) ________________________________ Message 0 _____________________________________ Time: 09:07:04 AM PST US From: Matt Dralle Subject: RV10-List: [Please Read] - Last Official Day of List Fund Raiser! Dear Listers, Its November 30th and that always means a couple of things. Its my birthday again; number 49 actually! But it also means that its that last official day of the Matronics Email List Fund Raiser! If you been thinking about picking up one of those really nice incentive gifts now is the time to jump on it!! If you've been meaning to make a Contribution this month but have been putting it off for some reason, NOW is the time! I will be posting the List of Contributors in a few days, so you'll probably want to be known as a person that supported the Lists! I want to thank everyone that has so generously made a Contribution this year in support of our Lists. It is your generosity that keeps this operation running and I don't ever forget it. The List Contribution Web Site is fast and easy. Please support our habit by making your Contribution right now: http://www.matronics.com/contribution Or, by dropping a personal check in the mail to: Matt Dralle / Matronics 581 Jeannie Way Livermore CA 94550 Thank you to all in advance! Matt Dralle Matronics Email List Administrator ________________________________ Message 1 _____________________________________ Time: 11:17:02 AM PST US From: Sean Stephens Subject: RV10-List: Rear Baffle Positioning Tips? Any tips on getting the #5 and #6 rear baffles in place? I'm having trouble even getting them in place for a test fit. Should I remove the oil return lines on #5 and #6 to help? Thanks, -Sean #40303 ________________________________ Message 2 _____________________________________ Time: 11:36:35 AM PST US Subject: Re: RV10-List: Rear Baffle Positioning Tips? From: Michael Kraus I don't recall having to remove any lines, but I did have to do some funky bending to get it in place. It is not easy, but it should fit... Sent from my iPhone On Nov 30, 2012, at 2:15 PM, Sean Stephens wrote: > > Any tips on getting the #5 and #6 rear baffles in place? I'm having trouble even getting them in place for a test fit. > > Should I remove the oil return lines on #5 and #6 to help? > > Thanks, > > -Sean #40303 > > > > ________________________________ Message 3 _____________________________________ Time: 12:19:42 PM PST US From: Kelly McMullen Subject: Re: RV10-List: Rear Baffle Positioning Tips? I just put mine on this morning. You have to wrestle #6 to get the inner portion past the cyl head and engine mount, then it drops right in. #5 was easy by comparison. No issue with oil lines. Aim the cutouts for the engine mounts right at the mount, and the curved portion angled a bit towards the rear. You will have to watch the oil return lines when you make the rods to tie the bottom of front and rear baffles together a bit later in the plans. On 11/30/2012 12:15 PM, Sean Stephens wrote: > > Any tips on getting the #5 and #6 rear baffles in place? I'm having > trouble even getting them in place for a test fit. > > Should I remove the oil return lines on #5 and #6 to help? > > Thanks, > > -Sean #40303 > > ----- No virus found in this message. Checked by AVG - www.avg.com ________________________________ Message 4 _____________________________________ Time: 12:19:47 PM PST US Subject: Re: RV10-List: Rear Baffle Positioning Tips? From: Bob Leffler You have to hold your tongue in the right position while pushing. ;^) Actually, you've got to twist it a bit. It's hard to describe, but once you figure it out, you install and remove them pretty quick. Sent from my iPhone On Nov 30, 2012, at 2:15 PM, Sean Stephens wrote: Any tips on getting the #5 and #6 rear baffles in place? I'm having trouble even getting them in place for a test fit. Should I remove the oil return lines on #5 and #6 to help? Thanks, -Sean #40303 ________________________________ Message 5 _____________________________________ Time: 12:20:31 PM PST US From: davidsoutpost@comcast.net Subject: Re: RV10-List: Rear Baffle Positioning Tips? Yeah. Massage them into position. No need to remove any lines. David Clifford RV-10 Builder Howell, MI ----- Original Message ----- From: "Michael Kraus" Sent: Friday, November 30, 2012 2:34:43 PM Subject: Re: RV10-List: Rear Baffle Positioning Tips? I don't recall having to remove any lines, but I did have to do some funky bending to get it in place. It is not easy, but it should fit... Sent from my iPhone On Nov 30, 2012, at 2:15 PM, Sean Stephens wrote: > > Any tips on getting the #5 and #6 rear baffles in place? I'm having trouble even getting them in place for a test fit. > > Should I remove the oil return lines on #5 and #6 to help? > > Thanks, > > -Sean #40303 > > > > ________________________________ Message 6 _____________________________________ Time: 01:03:35 PM PST US From: Sean Stephens Subject: Re: RV10-List: Rear Baffle Positioning Tips? I can't get either to go in at all. Not sure why the plans say to assemble these before putting them on. It seems it would be easier before assembling the whole corner. They aren't even close to going in and I'm scratching my rod covers on #6. On 11/30/12 2:19 PM, Kelly McMullen wrote: > > I just put mine on this morning. You have to wrestle #6 to get the > inner portion past the cyl head and engine mount, then it drops right > in. #5 was easy by comparison. No issue with oil lines. Aim the > cutouts for the engine mounts right at the mount, and the curved > portion angled a bit towards the rear. > You will have to watch the oil return lines when you make the rods to > tie the bottom of front and rear baffles together a bit later in the > plans. > > On 11/30/2012 12:15 PM, Sean Stephens wrote: >> >> Any tips on getting the #5 and #6 rear baffles in place? I'm having >> trouble even getting them in place for a test fit. >> >> Should I remove the oil return lines on #5 and #6 to help? >> >> Thanks, >> >> -Sean #40303 >> >> >> >> > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ________________________________ Message 7 _____________________________________ Time: 01:25:48 PM PST US From: Sean Stephens Subject: Re: RV10-List: Rear Baffle Positioning Tips? Ok, figured out #6. You need to take the oil cooler box off (un-cleco it) from the assembly in order to allow it to flex more. Now on to #5. Thanks all... -Sean On 11/30/12 3:03 PM, Sean Stephens wrote: > > I can't get either to go in at all. Not sure why the plans say to > assemble these before putting them on. It seems it would be easier > before assembling the whole corner. > > They aren't even close to going in and I'm scratching my rod covers on > #6. > > > On 11/30/12 2:19 PM, Kelly McMullen wrote: >> >> I just put mine on this morning. You have to wrestle #6 to get the >> inner portion past the cyl head and engine mount, then it drops right >> in. #5 was easy by comparison. No issue with oil lines. Aim the >> cutouts for the engine mounts right at the mount, and the curved >> portion angled a bit towards the rear. >> You will have to watch the oil return lines when you make the rods to >> tie the bottom of front and rear baffles together a bit later in the >> plans. >> >> On 11/30/2012 12:15 PM, Sean Stephens wrote: >>> >>> Any tips on getting the #5 and #6 rear baffles in place? I'm having >>> trouble even getting them in place for a test fit. >>> >>> Should I remove the oil return lines on #5 and #6 to help? >>> >>> Thanks, >>> >>> -Sean #40303 >>> >>> >>> >>> >> >> >> >> ----- >> No virus found in this message. >> Checked by AVG - www.avg.com >> >> >> >> >> > > ________________________________ Message 8 _____________________________________ Time: 01:29:09 PM PST US From: Jae Chang Subject: Re: RV10-List: Rear Baffle Positioning Tips? Definitely put blue tape or something on to protect your rocker covers. I probably had blue tape on mine for quite a while to protect scratching from baffles as well as the cowl while fitting. Jae -- #40533 RV-10 First flight 10/19/2011 Phase 1 Done 11/26/2011 do not archive On 11/30/2012 1:03 PM, Sean Stephens wrote: > > I can't get either to go in at all. Not sure why the plans say to > assemble these before putting them on. It seems it would be easier > before assembling the whole corner. > > They aren't even close to going in and I'm scratching my rod covers on > #6. ________________________________ Message 9 _____________________________________ Time: 01:31:04 PM PST US Subject: RV10-List: Re: Rear Baffle Positioning Tips? From: "mdaniell" All of the above is true, however there was a post somewhere about a builder having difficulty with the oil cooler brace, I think it turned out to be the wrong part. If you're absolutely sure it won't fitthen maybe check you have the right part. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=389634#389634 ________________________________ Message 10 ____________________________________ Time: 02:26:40 PM PST US From: Sean Stephens Subject: Re: RV10-List: Re: Rear Baffle Positioning Tips? The oil cooler brace fits fine. You just can't have it clecoed on the baffle while you are trying to get the baffle in or the baffle doesn't flex enough. #5 is getting there, but my oil pressure valve (not sure what it's really called) is in the way and the brace at the bottom of the baffle hits the case a bit before getting into place. Going to have to mod that a bit. On 11/30/12 3:30 PM, mdaniell wrote: > > All of the above is true, however there was a post somewhere about a builder having difficulty with the oil cooler brace, I think it turned out to be the wrong part. If you're absolutely sure it won't fitthen maybe check you have the right part. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=389634#389634 > > ________________________________ Message 11 ____________________________________ Time: 02:42:46 PM PST US From: "Rene Felker" Subject: RE: RV10-List: Re: Rear Baffle Positioning Tips? I had to mod mine for #5 to fit around the case and oil pressure valve. Rene' Felker N423CF 801-721-6080 -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Sean Stephens Sent: Friday, November 30, 2012 3:26 PM Subject: Re: RV10-List: Re: Rear Baffle Positioning Tips? The oil cooler brace fits fine. You just can't have it clecoed on the baffle while you are trying to get the baffle in or the baffle doesn't flex enough. #5 is getting there, but my oil pressure valve (not sure what it's really called) is in the way and the brace at the bottom of the baffle hits the case a bit before getting into place. Going to have to mod that a bit. On 11/30/12 3:30 PM, mdaniell wrote: > --> > > All of the above is true, however there was a post somewhere about a builder having difficulty with the oil cooler brace, I think it turned out to be the wrong part. If you're absolutely sure it won't fitthen maybe check you have the right part. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=389634#389634 > > ________________________________ Message 12 ____________________________________ Time: 04:25:45 PM PST US Subject: RV10-List: Re: Rear Baffle Positioning Tips? From: "bill.peyton" I loosed the oil return line on number 5. -------- Bill WA0SYV Aviation Partners, LLC Read this topic online here: http://forums.matronics.com/viewtopic.php?p=389650#389650 ________________________________ Message 13 ____________________________________ Time: 06:03:02 PM PST US Subject: Re: RV10-List: Re: Rear Baffle Positioning Tips? From: Kelly McMullen Yes, I had the wrong part, a rear baffle intended for the RV-7, not the 10, which was about 1/8" too short. I just mounted my baffles today. Yes, removing the oil cooler brace helps. Yes, it is a little tight with drain back tube on #5, but not hard to get that to fit. I found a little interference at crankcase is preventing my #5 from achieving correct position, so that screw holes at back of engine and brace line up. I think the plans should have called for assuring fit of all hardware before drilling the two holes for rear center brace. Oh well, just time and effort to make baffle fit the way it should. On Fri, Nov 30, 2012 at 2:30 PM, mdaniell wrote: > > All of the above is true, however there was a post somewhere about a > builder having difficulty with the oil cooler brace, I think it turned out > to be the wrong part. If you're absolutely sure it won't fitthen maybe > check you have the right part. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=389634#389634 > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.