----------------------------------------------------------
                           RV10-List Digest Archive
                                      ---
                     Total Messages Posted Fri 12/14/12: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 12:12 PM - Mounting Aerosport panel  (rvdave)
     2. 03:55 PM - Re: Mounting Aerosport panel  (Kelly McMullen)
     3. 04:02 PM - Re: Mounting Aerosport panel  (bill.peyton)
 
 
 
________________________________  Message 1  _____________________________________


Time: 12:12:25 PM PST US
Subject: RV10-List: Mounting Aerosport panel
From: "rvdave" <davidbf@centurytel.net>


Just received my symmetrical CF panel & trying to figure out how to mount it to
the existing framework.  I have a quick build fuselage with the forward top skin
and instrument ribs put together as an assembly, the lower F1003b brace riveted
in which I'm assuming I need to remove and not use.  Question is clearances
at the forward edge of CF panel and CF panel sub brace and top skin.  As it
is the CF sits proud all the way around the sub brace.  Am I suppose to remove
material at top, sides and forward to allow 1) CF panel to fit flat against
sub brace?  2)room for glare shield material?  3) CF panel to sit as far forward
as possible?   
As it sits right now the panel will cover about half of the grab holes of top skin
not leaving enough room to fit fingers in.
Anyone with photos of similar phase of install or insight that could help?

--------
Dave Ford
RV6 flying
RV10 building
Cadillac, MI


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=390457#390457


________________________________  Message 2  _____________________________________


Time: 03:55:47 PM PST US
From: Kelly McMullen <kellym@aviating.com>
Subject: Re: RV10-List: Mounting Aerosport panel


I just dealt with this last month. IMHO, the easy way is to slot the 
holes that the subframe mounts to the cowl deck structure by about 1/8". 
A Dremel rotary file is probably the quickest, if not easiest to 
control. The other option is a whole lot of nasty sanding down the CF.
Kelly
On 12/14/2012 1:11 PM, rvdave wrote:
>
> Just received my symmetrical CF panel & trying to figure out how to mount it
to the existing framework.  I have a quick build fuselage with the forward top
skin and instrument ribs put together as an assembly, the lower F1003b brace
riveted in which I'm assuming I need to remove and not use.  Question is clearances
at the forward edge of CF panel and CF panel sub brace and top skin.  As
it is the CF sits proud all the way around the sub brace.  Am I suppose to remove
material at top, sides and forward to allow 1) CF panel to fit flat against
sub brace?  2)room for glare shield material?  3) CF panel to sit as far forward
as possible?
> As it sits right now the panel will cover about half of the grab holes of top
skin not leaving enough room to fit fingers in.
> Anyone with photos of similar phase of install or insight that could help?
>
> --------
> Dave Ford
> RV6 flying
> RV10 building
> Cadillac, MI
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=390457#390457
>
>


-----
No virus found in this message.
Checked by AVG - www.avg.com


________________________________  Message 3  _____________________________________


Time: 04:02:00 PM PST US
Subject: RV10-List: Re: Mounting Aerosport panel
From: "bill.peyton" <peyton.b@sbcglobal.net>


I installed the non-sym  standard panel.  Here is a photo looking up and showing
the attachment of the new substructure from Aerosport.  If you haven't already,
download the installation instructions.  The standard Vans panel is completely
replaced when you install the Aerosport panel.

--------
Bill 
WA0SYV
Aviation Partners, LLC


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=390469#390469


Attachments: 

http://forums.matronics.com//files/img_1957_179.jpg
http://forums.matronics.com//files/img_1957_192.jpg


 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               rv10-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/RV10-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/rv10-list
Browse Digests                   http://www.matronics.com/digest/rv10-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.