---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 01/06/13: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:22 AM - Re: Control Column Deflection & Length (bill.peyton) 2. 11:45 AM - Re: Re: Control Column Deflection & Length (Patrick Pulis) 3. 01:13 PM - Another RV-10 down? (Michael Kraus) ________________________________ Message 1 _____________________________________ Time: 07:22:50 AM PST US Subject: RV10-List: Re: Control Column Deflection & Length From: "bill.peyton" Geoff is correct. I have the Aerosport Panel also. You will end up with the stick cut down almost the entire amount. You should also cut the lower section so that it will insert into the control arm further and bring it further back. After you hook up the controls, you need to make an elevator stop which will prevent the stick from hitting the front panel on the inside corner. After that, you can adjust all of the push rods to obtain the correct amount of travel required by the spec. You need to make sure that the controls have enough clearance WITH your hands around the grip. -------- Bill WA0SYV Aviation Partners, LLC Read this topic online here: http://forums.matronics.com/viewtopic.php?p=391703#391703 Attachments: http://forums.matronics.com//files/img_2596_203.jpg ________________________________ Message 2 _____________________________________ Time: 11:45:57 AM PST US Subject: Re: RV10-List: Re: Control Column Deflection & Length From: Patrick Pulis Many thanks Bill & Geoff. Warm regards Patrick On 07/01/2013, at 1:52 AM, "bill.peyton" wrote: > > Geoff is correct. I have the Aerosport Panel also. You will end up with the stick cut down almost the entire amount. You should also cut the lower section so that it will insert into the control arm further and bring it further back. After you hook up the controls, you need to make an elevator stop which will prevent the stick from hitting the front panel on the inside corner. After that, you can adjust all of the push rods to obtain the correct amount of travel required by the spec. You need to make sure that the controls have enough clearance WITH your hands around the grip. > > -------- > Bill > WA0SYV > Aviation Partners, LLC > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=391703#391703 > > > > > Attachments: > > http://forums.matronics.com//files/img_2596_203.jpg > > > > > > > ________________________________ Message 3 _____________________________________ Time: 01:13:22 PM PST US Subject: RV10-List: Another RV-10 down? From: Michael Kraus http://www.10news.com/news/experimental-aircraft-goes-down-near-julian-pilot -not-injured-01052013 Do not archive -Mike Kraus RV-4 sold :-( RV-10 flying :-) KitFox SS7 Radial building :-) ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.