---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Fri 06/14/13: 9 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:10 AM - Re: Routing electrical conduit (Carl Froehlich) 2. 04:43 AM - Re: RV-10 Shop Humor (Tim Olson) 3. 05:58 AM - Re: Routing electrical conduit (Kelly McMullen) 4. 09:43 AM - RTV silicone (bob88) 5. 10:01 AM - Re: RTV silicone (Marcus Cooper) 6. 10:11 AM - Re: RTV silicone (Tim Olson) 7. 10:47 AM - Re: Routing electrical conduit (Jim Berry) 8. 11:42 AM - How many turns to adjust low RPM on Silver Hawk EX injector (Mike Whisky) 9. 12:43 PM - Re: RV-10 Shop Humor (Ron B.) ________________________________ Message 1 _____________________________________ Time: 04:10:20 AM PST US From: "Carl Froehlich" Subject: RE: RV10-List: Routing electrical conduit I didn't use the Van's electrical kit but here is how I ran the three conduits on each side. Note - where these lines pass through the rear seat pan or ribs I used an adhesive to make sure there was no relative motion between the corrugated conduit and the aluminum. On the side lightning holes I added large rubber grommets in the lighting holes. I figured I needed two runs on each side, but added a third just in case. I ended up using it. I have the two ADHRS modules mounted aft of the baggage compartment as most do, so they have two 1/4" lines from the wing going aft (pitot and AOA) and two going from aft up to the panel (pitot and static) as I have a couple of analog gauges in the panel. All wire and tubing runs are in the conduit including the #2 welding cable from both masters to the starter solenoid. Carl RV-8A (sold last week) RV-10, 95 hrs -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of bob88 Sent: Friday, June 14, 2013 1:48 AM Subject: RV10-List: Routing electrical conduit Who has figured out how to route the conduit supplied in Van's electrical kit from front to the rear of baggage area? Other than the too small holes provided on the left and occupied by the P27 battery cable plus similar on the right, it appears to me that cutting holes in some fairly beefy looking structural members may be the only way. Am I missing something? OK to cut? Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402667#402667 ________________________________ Message 2 _____________________________________ Time: 04:43:02 AM PST US From: Tim Olson Subject: Re: RV10-List: RV-10 Shop Humor Hillarious! I know exactly how you feel....I had a bad experience with dumping a can of contact cement on my bare chest once. Lets just say... "yes, it's hard to get out, but DO NOT resort to using NAIR (acid that will eat your skin off) to get the hair and glue out". Yes, I know exactly how you feel... Tim Olson - RV-10 N104CD do not archive On 6/13/2013 10:01 PM, Phillip Perry wrote: > True story - Just occurred. > ====================== > > > So I'm working on the airplane tonight and as usual, I'm doing > fiberglass work. Hopefully I can get this cabin top painted in > the next week or so. > > > I just finished for the night, took a shower, and looked in > the mirror. What's that? That, sir, is a wad of epoxy and > filler stuck on your nipple and chest hair. > > > I know I should have been wearing a shirt, but it's 95 degrees > in Houston and I'm not going to do it. Not when I'm just > dinking around with filler and patching a few voids here and > there. > > So, I bravely grabbed the wad of epoxy and yanked.......... > > > Then I cried. > > > Have you ever waxed your nipple? If you haven't, you should > try it! (on someone else) > > - Let's just get paint on this thing and call it good. > > Phil > Do not Archive > > * > > > * > ________________________________ Message 3 _____________________________________ Time: 05:58:23 AM PST US Subject: Re: RV10-List: Routing electrical conduit From: Kelly McMullen Avoid cutting structure. See Carl's response for one way to do it. On Thu, Jun 13, 2013 at 10:48 PM, bob88 wrote: > > Who has figured out how to route the conduit supplied in Van's electrical > kit from front to the rear of baggage area? Other than the too small holes > provided on the left and occupied by the P27 battery cable plus similar on > the right, it appears to me that cutting holes in some fairly beefy looking > structural members may be the only way. Am I missing something? OK to cut? > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=402667#402667 > > -- - sent from the microchip implanted in my forearm ________________________________ Message 4 _____________________________________ Time: 09:43:04 AM PST US Subject: RV10-List: RTV silicone From: "bob88" Is there an RTV silicone available from regular hardware store that is safe on aluminum? Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402687#402687 ________________________________ Message 5 _____________________________________ Time: 10:01:23 AM PST US Subject: Re: RV10-List: RTV silicone From: Marcus Cooper I've always used the red high temp silicone on several airplanes with no issues. I've also read repeatedly that's the recommendation by others. Marcus On Jun 14, 2013, at 12:42 PM, "bob88" wrote: do not archive Is there an RTV silicone available from regular hardware store that is safe on aluminum? Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402687#402687 ________________________________ Message 6 _____________________________________ Time: 10:11:57 AM PST US Subject: Re: RV10-List: RTV silicone From: Tim Olson Just look for "sensor safe". Tim On Jun 14, 2013, at 12:01 PM, Marcus Cooper wrote: > > I've always used the red high temp silicone on several airplanes with no issues. I've also read repeatedly that's the recommendation by others. > > Marcus > > > On Jun 14, 2013, at 12:42 PM, "bob88" wrote: > do not archive > > Is there an RTV silicone available from regular hardware store that is safe on aluminum? > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=402687#402687 > > > > > > > > > > > > > > > > ________________________________ Message 7 _____________________________________ Time: 10:47:04 AM PST US Subject: RV10-List: Re: Routing electrical conduit From: "Jim Berry" I contacted Vans when I was doing this step, and they said it was OK to enlarge the holes in the bulkhead sides to 1". Jim Berry RV-10 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402694#402694 ________________________________ Message 8 _____________________________________ Time: 11:42:13 AM PST US Subject: RV10-List: How many turns to adjust low RPM on Silver Hawk EX injector From: "Mike Whisky" Hi, my idle RPM is too high 900 RPM, I need to adjust the throttle lever on the Silver Hawk EX and wonder if someone knows how many turns on the adjustment nut equal 100 RPM. Thanks Mike -------- RV-10 builder (final system testing) #511 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402696#402696 ________________________________ Message 9 _____________________________________ Time: 12:43:04 PM PST US Subject: RV10-List: Re: RV-10 Shop Humor From: "Ron B." Moral of the story, move to Nova Scotia. You will always need to wear at least a T-shirt here. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=402699#402699 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.