Today's Message Index:
----------------------
1. 03:32 PM - Re: Re: doors (Bmts)
2. 07:10 PM - FAB Box Servo Mixture Arm (mds4878)
3. 07:27 PM - C/S-13 SPINNER FOR SALE (mds4878)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thx Jack
I also had index holes that didn't match up worth a darn, so I used a spacer to
raise the doors and then drilled the doors to the fuse all this while the top
was bolted to the fuse. I'm hoping they are high enough to have Sean's latch
clears the McMaster seal. Thx, Rick
Sent from my iPhone
On 2013-06-25, at 1:53 AM, "Jackm" <jackm@vinetechequipment.com> wrote:
>
> Rick,
>
> I agree with all the above...one thing I would add is when you go to cleco your
door skins to the fuse, One,make sure your cabin top is bolted to fuse in place
as you would on final install and Two DO NOT use the two fore and aft dimple
index to fix the doors to the fuse during epoxy fit. I found the indicator
dimples to be aprox 3/16 to high on the door on ours. You will find the doors
will be too low when you go trim to the cabin top opening. I did this on left
door and had to roll the complete door up to get adequate clearance between the
lower jam and door. You don't want this as you formed the door to fit the cabin
top curve. Right side we built spacers for the lower and sides to fit between
the jam and door inner ledge. Remember to add the door skins thickness dim
to the spacer as the door needs to drop down to be flush with the cabin top
when you trim door to fit the opening. This will also ensure that Seans latch
will clear the lower jam when you install them. Hope !
> this makes sense....I almost threw away the left door after I realized what I
did.
>
> --------
> Jackm
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=403371#403371
>
>
>
>
>
>
>
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | FAB Box Servo Mixture Arm |
I have a IO 540 with a bendix fuel servo that has a straight mixture arm but I
need the offset arm. Does anyone have one for sale or trade? The straight arm
doesn't fit the FAB box from Van's. :(
--------
RV-10 #40447
Fuselage almost done.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=403437#403437
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | C/S-13 SPINNER FOR SALE |
I bought a C/S-13 spinner for my plane but I will not be using it because a spinner
comes with my prop. I want 120.00 plus shipping.
Mike 612-590-8604.
--------
RV-10 #40447
Fuselage almost done.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=403439#403439
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|