---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Tue 06/25/13: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:32 PM - Re: Re: doors (Bmts) 2. 07:10 PM - FAB Box Servo Mixture Arm (mds4878) 3. 07:27 PM - C/S-13 SPINNER FOR SALE (mds4878) ________________________________ Message 1 _____________________________________ Time: 03:32:53 PM PST US Subject: Re: RV10-List: Re: doors From: Bmts Thx Jack I also had index holes that didn't match up worth a darn, so I used a spacer to raise the doors and then drilled the doors to the fuse all this while the top was bolted to the fuse. I'm hoping they are high enough to have Sean's latch clears the McMaster seal. Thx, Rick Sent from my iPhone On 2013-06-25, at 1:53 AM, "Jackm" wrote: > > Rick, > > I agree with all the above...one thing I would add is when you go to cleco your door skins to the fuse, One,make sure your cabin top is bolted to fuse in place as you would on final install and Two DO NOT use the two fore and aft dimple index to fix the doors to the fuse during epoxy fit. I found the indicator dimples to be aprox 3/16 to high on the door on ours. You will find the doors will be too low when you go trim to the cabin top opening. I did this on left door and had to roll the complete door up to get adequate clearance between the lower jam and door. You don't want this as you formed the door to fit the cabin top curve. Right side we built spacers for the lower and sides to fit between the jam and door inner ledge. Remember to add the door skins thickness dim to the spacer as the door needs to drop down to be flush with the cabin top when you trim door to fit the opening. This will also ensure that Seans latch will clear the lower jam when you install them. Hope ! > this makes sense....I almost threw away the left door after I realized what I did. > > -------- > Jackm > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=403371#403371 > > > > > > > > > > ________________________________ Message 2 _____________________________________ Time: 07:10:07 PM PST US Subject: RV10-List: FAB Box Servo Mixture Arm From: "mds4878" I have a IO 540 with a bendix fuel servo that has a straight mixture arm but I need the offset arm. Does anyone have one for sale or trade? The straight arm doesn't fit the FAB box from Van's. :( -------- RV-10 #40447 Fuselage almost done. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=403437#403437 ________________________________ Message 3 _____________________________________ Time: 07:27:43 PM PST US Subject: RV10-List: C/S-13 SPINNER FOR SALE From: "mds4878" I bought a C/S-13 spinner for my plane but I will not be using it because a spinner comes with my prop. I want 120.00 plus shipping. Mike 612-590-8604. -------- RV-10 #40447 Fuselage almost done. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=403439#403439 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.