---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 09/15/13: 8 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 03:03 AM - B and C pad mounted alternateor (Rob Kermanj) 2. 06:57 AM - Re: B and C pad mounted alternateor (Linn Walters) 3. 07:07 AM - Re: B and C pad mounted alternateor (Rob Kermanj) 4. 07:12 AM - Re: B and C pad mounted alternateor (Linn Walters) 5. 07:25 AM - Re: B and C pad mounted alternateor (Linn Walters) 6. 07:55 AM - Re: B and C pad mounted alternator (Carl Froehlich) 7. 10:07 AM - Re: B and C pad mounted alternator (Rob Kermanj) 8. 02:52 PM - Re: Flying the Hudson through NY and to Washington DC. (ivankris) ________________________________ Message 1 _____________________________________ Time: 03:03:39 AM PST US From: Rob Kermanj Subject: RV10-List: B and C pad mounted alternateor Anyone using B&C's pad mounted 20 amp alternator as a primary? I checked my consumption and with everything on (exception fuel pump) it is 22 amps. I have 500 hrs on Van's alternator and dread having to pull a prop out on a trip to replace a belt or the alternator. Thanks. Do not archive ________________________________ Message 2 _____________________________________ Time: 06:57:45 AM PST US From: Linn Walters Subject: Re: RV10-List: B and C pad mounted alternateor On 9/15/2013 6:02 AM, Rob Kermanj wrote: > > Anyone using B&C's pad mounted 20 amp alternator as a primary? I'm not using mine yet. > I checked my consumption and with everything on (exception fuel pump) it is 22 amps. > > I have 500 hrs on Van's alternator and dread having to pull a prop out on a trip to replace a belt or the alternator. A properly tensioned and aligned belt will last a long time. I had 2200+ hours on one belt (my AA-1B) before I changed it. It was showing signs of cracking so it was a preventative move. You should have a lot of warning before a belt failure. It should be on your checklist at annual and damage is easy to see. Now for your 'dread'. Next annual put a 'backup' belt on the nose of the engine and ty-wrap it to the forward lift ring to keep it out of the way. I have seen the 'replacement' belt be unuseable because the primary lasted so long and it was just dried out. I don't have any data but you should get at least 1000 hours out of a belt so change it during an annual or when you pull the prop for some reason. Belts are cheap. Linn > > Thanks. > > Do not archive > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ________________________________ Message 3 _____________________________________ Time: 07:07:23 AM PST US Subject: Re: RV10-List: B and C pad mounted alternateor From: Rob Kermanj Good advice Linn. I will seriously consider it. How about the alt? Anyone has failure hours in service data? My first one lasted 200 hrs. This one has 500 hrs and I have a long trip to take next month. I see black powder on the alt and I am worried. Do not archive. Rob Kermanj Sent from my iPad On Sep 15, 2013, at 9:57 AM, Linn Walters wrote: > > On 9/15/2013 6:02 AM, Rob Kermanj wrote: >> >> Anyone using B&C's pad mounted 20 amp alternator as a primary? > I'm not using mine yet. >> I checked my consumption and with everything on (exception fuel pump) it is 22 amps. >> >> I have 500 hrs on Van's alternator and dread having to pull a prop out on a trip to replace a belt or the alternator. > A properly tensioned and aligned belt will last a long time. > I had 2200+ hours on one belt (my AA-1B) before I changed it. It was showing signs of cracking so it was a preventative move. You should have a lot of warning before a belt failure. It should be on your checklist at annual and damage is easy to see. > > Now for your 'dread'. Next annual put a 'backup' belt on the nose of the engine and ty-wrap it to the forward lift ring to keep it out of the way. I have seen the 'replacement' belt be unuseable because the primary lasted so long and it was just dried out. I don't have any data but you should get at least 1000 hours out of a belt so change it during an annual or when you pull the prop for some reason. Belts are cheap. > Linn > >> >> Thanks. >> >> Do not archive >> >> >> >> >> >> >> ----- >> No virus found in this message. >> Checked by AVG - www.avg.com > > > > > ________________________________ Message 4 _____________________________________ Time: 07:12:55 AM PST US From: Linn Walters Subject: Re: RV10-List: B and C pad mounted alternateor That should be 'conditional inspection' not 'annual' .... old habits are hard to break. Linn On 9/15/2013 9:57 AM, Linn Walters wrote: > > On 9/15/2013 6:02 AM, Rob Kermanj wrote: >> >> Anyone using B&C's pad mounted 20 amp alternator as a primary? > I'm not using mine yet. >> I checked my consumption and with everything on (exception fuel pump) >> it is 22 amps. >> >> I have 500 hrs on Van's alternator and dread having to pull a prop >> out on a trip to replace a belt or the alternator. > A properly tensioned and aligned belt will last a long time. > I had 2200+ hours on one belt (my AA-1B) before I changed it. It was > showing signs of cracking so it was a preventative move. You should > have a lot of warning before a belt failure. It should be on your > checklist at annual and damage is easy to see. > > Now for your 'dread'. Next annual put a 'backup' belt on the nose of > the engine and ty-wrap it to the forward lift ring to keep it out of > the way. I have seen the 'replacement' belt be unuseable because the > primary lasted so long and it was just dried out. I don't have any > data but you should get at least 1000 hours out of a belt so change it > during an annual or when you pull the prop for some reason. Belts are > cheap. > Linn > >> >> Thanks. >> >> Do not archive >> >> >> >> >> >> >> ----- >> No virus found in this message. >> Checked by AVG - www.avg.com >> >> > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ________________________________ Message 5 _____________________________________ Time: 07:25:14 AM PST US From: Linn Walters Subject: Re: RV10-List: B and C pad mounted alternateor On 9/15/2013 10:17 AM, Rob Kermanj wrote: > > Good advice Linn. I will seriously consider it. > > How about the alt? Anyone has failure hours in service data? My first one lasted 200 hrs. This one has 500 hrs and I have a long trip to take next month. I see black powder on the alt and I am worried. You need to find out where the black powder is coming from. I suspect the belt. Look at the baffling around the belt for signs that the clearance wasn't enough. I've read (here I think) about some original installations not having the flywheel and alternator pulleys aligned and needing modifications on the alternator mounting to make it fit properly. That may have been a Plane Power problem though. Have a safe trip. Linn > > > Do not archive. > > Rob Kermanj > Sent from my iPad > > On Sep 15, 2013, at 9:57 AM, Linn Walters wrote: > >> >> On 9/15/2013 6:02 AM, Rob Kermanj wrote: >>> >>> Anyone using B&C's pad mounted 20 amp alternator as a primary? >> I'm not using mine yet. >>> I checked my consumption and with everything on (exception fuel pump) it is 22 amps. >>> >>> I have 500 hrs on Van's alternator and dread having to pull a prop out on a trip to replace a belt or the alternator. >> A properly tensioned and aligned belt will last a long time. >> I had 2200+ hours on one belt (my AA-1B) before I changed it. It was showing signs of cracking so it was a preventative move. You should have a lot of warning before a belt failure. It should be on your checklist at annual and damage is easy to see. >> >> Now for your 'dread'. Next annual put a 'backup' belt on the nose of the engine and ty-wrap it to the forward lift ring to keep it out of the way. I have seen the 'replacement' belt be unuseable because the primary lasted so long and it was just dried out. I don't have any data but you should get at least 1000 hours out of a belt so change it during an annual or when you pull the prop for some reason. Belts are cheap. >> Linn >> >>> Thanks. >>> >>> Do not archive >>> >>> >>> >>> >>> >>> >>> ----- >>> No virus found in this message. >>> Checked by AVG - www.avg.com >> >> >> >> > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ________________________________ Message 6 _____________________________________ Time: 07:55:27 AM PST US From: "Carl Froehlich" Subject: RE: RV10-List: B and C pad mounted alternator As already pointed out an alternator belt tends to last a long time if not misaligned. If you have reason to pull the prop however, replacing the belt is always an easy preventative maintenance step. The standard 60amp alternator (B&C or Plane Power) is easily replaced without pulling the prop. WRT only running the little 20 amp pad alternator, I suggest you are trading good for not as good: - you will be limited to a day VFR aircraft - no margin at all to charge the battery(s) after engine start - the little alternator always running full blast - the only B&C alternator failure I've seen was one of these pad units - the breakable coupling broke. - any auto part store will provide an acceptable alternator if you get stuck someplace (assuming you are using an internally regulated alternator like the Plane Power unit). The little B&C pad alternator is a "send it via FedEx" process. On the larger picture, the alternator is not the most reliable element in an electrical power distribution system, it is the battery. This assumes you don't design in a single point failure such as a single battery (or two batteries always in parallel), single master relay, a single ground connection, single avionics master switch, or similar. Adding an extra alternator (if that is your direction) protects only from the primary alternator failing. Having a robust battery power distribution with a single alternator and adequate battery amp/hr capacity, I offer, is better risk mitigation. Carl -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Rob Kermanj Sent: Sunday, September 15, 2013 6:03 AM Subject: RV10-List: B and C pad mounted alternateor Anyone using B&C's pad mounted 20 amp alternator as a primary? I checked my consumption and with everything on (exception fuel pump) it is 22 amps. I have 500 hrs on Van's alternator and dread having to pull a prop out on a trip to replace a belt or the alternator. Thanks. Do not archive ________________________________ Message 7 _____________________________________ Time: 10:07:17 AM PST US Subject: Re: RV10-List: B and C pad mounted alternator From: Rob Kermanj Thanks Carl. Your points are well taken. You guys are saving me about 41200 box. Do not archive. On Sep 15, 2013, at 10:54 AM, "Carl Froehlich" wrote: > > As already pointed out an alternator belt tends to last a long time if not > misaligned. If you have reason to pull the prop however, replacing the belt > is always an easy preventative maintenance step. The standard 60amp > alternator (B&C or Plane Power) is easily replaced without pulling the prop. > > WRT only running the little 20 amp pad alternator, I suggest you are trading > good for not as good: > - you will be limited to a day VFR aircraft > - no margin at all to charge the battery(s) after engine start > - the little alternator always running full blast > - the only B&C alternator failure I've seen was one of these pad units - the > breakable coupling broke. > - any auto part store will provide an acceptable alternator if you get stuck > someplace (assuming you are using an internally regulated alternator like > the Plane Power unit). The little B&C pad alternator is a "send it via > FedEx" process. > > On the larger picture, the alternator is not the most reliable element in an > electrical power distribution system, it is the battery. This assumes you > don't design in a single point failure such as a single battery (or two > batteries always in parallel), single master relay, a single ground > connection, single avionics master switch, or similar. Adding an extra > alternator (if that is your direction) protects only from the primary > alternator failing. Having a robust battery power distribution with a > single alternator and adequate battery amp/hr capacity, I offer, is better > risk mitigation. > > Carl > > > > -----Original Message----- > From: owner-rv10-list-server@matronics.com > [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Rob Kermanj > Sent: Sunday, September 15, 2013 6:03 AM > To: rv10-list@matronics.com > Subject: RV10-List: B and C pad mounted alternateor > > > Anyone using B&C's pad mounted 20 amp alternator as a primary? > > I checked my consumption and with everything on (exception fuel pump) it is > 22 amps. > > I have 500 hrs on Van's alternator and dread having to pull a prop out on a > trip to replace a belt or the alternator. > > Thanks. > > Do not archive > > > > > > > > ________________________________ Message 8 _____________________________________ Time: 02:52:56 PM PST US Subject: RV10-List: Re: Flying the Hudson through NY and to Washington DC. From: "ivankris" Last Monday Sept. 9, we loaded the RV-10 for a 3 day visit to NY and Washington DC. The weather gods were definitely smiling on us as we had tail winds and visibility of 50+ miles. Enroute to NY. we had a clear view of Niagara Falls as we passed just north of it, also an excellent view of the Finger Lakes as we passed overhead. First stop was West Chester Co. Airport in White Plains NY for Customs. Only a few "Quality" minutes with these officers of the law and we were on our way. The flight down the Hudson River turned out to be easier than expected. I was well prepared having taken the on-line course as suggested. The NY TAC Chart is a must for his flight as it sets out clear instructions with mandatory reporting points ect. After the flight down the Hudson and a lunch and fuel stop in Farmingdale NJ we continued to Gaithersburg MD near Washington for what turned out to be a fantastic trip. -------- Ivan Kristensen. www.ivankristensen.com Builder # 40838 Flying (430hrs.) C-GMDV Read this topic online here: http://forums.matronics.com/viewtopic.php?p=408636#408636 Attachments: http://forums.matronics.com//files/4_149.jpg http://forums.matronics.com//files/7_992.jpg http://forums.matronics.com//files/5_196.jpg http://forums.matronics.com//files/1_174.jpg http://forums.matronics.com//files/3_155.jpg http://forums.matronics.com//files/1a_555.jpg ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.