---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Thu 10/24/13: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:11 AM - Re: Bonanco brake lines (Dave Fritzsche (Building)) 2. 01:03 AM - Re: Prop spinner cutouts (Patrick Pulis) 3. 05:52 AM - Re: Prop spinner cutouts (Kelly McMullen) 4. 07:18 AM - Re: Prop spinner cutouts (John Trollinger) 5. 08:29 PM - Re: Copperstate RV-10 Nest 2013 (woxofswa) ________________________________ Message 1 _____________________________________ Time: 12:11:12 AM PST US From: "Dave Fritzsche (Building)" Subject: Re: RV10-List: Bonanco brake lines Phil Perry and Gordon Anderson, I am ready to order fuel and brake lines and was impressed with your installations and Gordon's description he put together in pdf. Gordon, do the measurements you show in the table take into account shortening the two lines that Phil referred to in his U-tube video? Have you put your wings on yet to verify those connections? Anything either of you would change if you had it to do over? Dave On 1/24/2012 9:24 AM, Gordon Anderson wrote: ~~~~~~~~~~~~~~ Dave Fritzsche 40813 Puyallup, WA Wings > Having an intense fear of flaring, I chose to replace all the aluminum and plastic tubing with Bonaco lines. > > I was very impressed by Phil Perry's installation and copied it, with some slight modifications. For anyone interested, the attached document shows the results. There is a table at the end of the document with the hose sizes, lengths, fittings and clocking not only for the standard Bonaco RV-10 set but also for the tunnel brake and fuel hoses. Note the caveat on the fuel lines from the tanks - I haven't yet had the wings on to verify the length and clocking but as far as I can see they are good! As for the rest I am happy with the result. > > > Cheers, > > Gordon Anderson > 41015, Switzerland ________________________________ Message 2 _____________________________________ Time: 01:03:18 AM PST US Subject: Re: RV10-List: Prop spinner cutouts From: Patrick Pulis Chris Lycoming can issue you with the correct cut out template. I don't have it on my iPad, however ill send it to you once I'm on my computer. Warm regards Patrick Pulis > On 21 Oct 2013, at 8:33, "Chris Hukill" wrote: > > I'm trying to determine the optimum cutout dimensions for the blades on th e 2 bladed Hartzell blended airfoil prop as Vans sells, using the standard s pinner kit. The instructions tell you to rotate the blades thru full travel t o check for clearance, however I don't have an engine to mount the prop to y et, and it's not possible to move the blades without one. I am trying to get as tight of fit as is possible. I have looked at production airplane's inst allations, and they have a much larger clearance than I would consider aesth etic. Has anyone made a template or drawings that would provide the dimensio ns that I need? > Chris Hukill > > 3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3 D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D 3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3 D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D 3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3 D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D 3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3 D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D > ________________________________ Message 3 _____________________________________ Time: 05:52:26 AM PST US From: Kelly McMullen Subject: Re: RV10-List: Prop spinner cutouts Hmm, I'd be surprised if Lycoming had that information, but Hartzell likely has it, because Hartzell makes spinners for their props. On 10/24/2013 1:02 AM, Patrick Pulis wrote: > Chris > > Lycoming can issue you with the correct cut out template. I don't have > it on my iPad, however ill send it to you once I'm on my computer. > > Warm regards > > Patrick Pulis > > > On 21 Oct 2013, at 8:33, "Chris Hukill" > wrote: > >> I'm trying to determine the optimum cutout dimensions for the blades >> on the 2 bladed Hartzell blended airfoil prop as Vans sells, using >> the standard spinner kit. The instructions tell you to rotate the >> blades thru full travel to check for clearance, however I don't have >> an engine to mount the prop to yet, and it's not possible to move the >> blades without one. I am trying to get as tight of fit as is >> possible. I have looked at production airplane's installations, and >> they have a much larger clearance than I would consider aesthetic. >> Has anyone made a template or drawings that would provide the >> dimensions that I need? >> Chris Hukill >> * >> >> >> * > * > > > * ________________________________ Message 4 _____________________________________ Time: 07:18:53 AM PST US Subject: Re: RV10-List: Prop spinner cutouts From: John Trollinger Is this what you are looking for? On Thu, Oct 24, 2013 at 8:51 AM, Kelly McMullen wrote: > > Hmm, I'd be surprised if Lycoming had that information, but Hartzell > likely has it, because Hartzell makes spinners for their props. > > On 10/24/2013 1:02 AM, Patrick Pulis wrote: > >> Chris >> >> Lycoming can issue you with the correct cut out template. I don't have it >> on my iPad, however ill send it to you once I'm on my computer. >> >> Warm regards >> >> Patrick Pulis >> >> >> On 21 Oct 2013, at 8:33, "Chris Hukill" > cjhukill@cox.net>> wrote: >> >> I'm trying to determine the optimum cutout dimensions for the blades on >>> the 2 bladed Hartzell blended airfoil prop as Vans sells, using the >>> standard spinner kit. The instructions tell you to rotate the blades thru >>> full travel to check for clearance, however I don't have an engine to mount >>> the prop to yet, and it's not possible to move the blades without one. I am >>> trying to get as tight of fit as is possible. I have looked at production >>> airplane's installations, and they have a much larger clearance than I >>> would consider aesthetic. Has anyone made a template or drawings that would >>> provide the dimensions that I need? >>> Chris Hukill >>> * >>> >>> >>> * >>> >> * >> >> >> * >> > > ________________________________ Message 5 _____________________________________ Time: 08:29:41 PM PST US Subject: RV10-List: Re: Copperstate RV-10 Nest 2013 From: "woxofswa" All set up due south of the Van's display. Easier to get to now that the fence is gone. Lots of seating and shade. Cold drinks in the cooler. -------- Myron Nelson Mesa, AZ Emp completed, QB wings completed, legacy build fuse on gear. FWF complete. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=411376#411376 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.