---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Thu 03/06/14: 8 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:04 AM - fuselage rolling rack (Chris Hukill) 2. 01:33 PM - Re: Wing tip question (Rocketman1988) 3. 01:36 PM - Re: Wing tip question (Rocketman1988) 4. 02:16 PM - Re: Wing tip question (dmaib@me.com) 5. 05:25 PM - Re: fuselage rolling rack (rvdave) 6. 06:34 PM - Re: Wing tip question (Ron B.) 7. 07:35 PM - Re: Re: fuselage rolling rack (Kelly McMullen) 8. 08:21 PM - Re: Wing tip question (Rocketman1988) ________________________________ Message 1 _____________________________________ Time: 05:04:45 AM PST US From: "Chris Hukill" Subject: RV10-List: fuselage rolling rack I have finally got my RV10 project off the rack and onto it=99s gear and no longer need the rack. It is a welded steel rack that has worked great and I am offering it to anyone who is close enough to Las Vegas to come and get it, for free. Chris Hukill hangin the motor ________________________________ Message 2 _____________________________________ Time: 01:33:00 PM PST US Subject: RV10-List: Re: Wing tip question From: "Rocketman1988" Yeah, not so sure about following the plans on the wingtip alignment. When you get to the wingtip section, hang the flap and aileron on that wing, align them, then fit the wingtip. If you just put the wingtip on and keep it as tight to the skin flange as you can, YOU MAY BE UNHAPPY with the result. And the TE of the wingtip can move 11/16"...ask me how I know :( Luckily, I had only drilled a few holes and I had been reading the forums on this issue, so I went back and hung the flap and aileron, then aligned them in the specified position. Turns out that the wingtip was "off" by about 1/2 of a hole diameter at the LE...yep, 1/16". Sure glad I checked it before drilling the final hole size...Looks good now, within 3/32" tip/aileron/flap... Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419877#419877 ________________________________ Message 3 _____________________________________ Time: 01:36:06 PM PST US Subject: RV10-List: Re: Wing tip question From: "Rocketman1988" I should add that I followed the plans exactly on this first tip and must have gotten lucky because it matched the flap/aileron when finished... Did the same on the second tip and, well, that's the post above... Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419878#419878 ________________________________ Message 4 _____________________________________ Time: 02:16:14 PM PST US Subject: RV10-List: Re: Wing tip question From: "dmaib@me.com" I do remember that it was a two person job to make sure the wingtip was pushed securely into position and held very firmly in position while the holes were drilled. IIRC it really needs to be pushed forward with some force to fit the leading edge properly. -------- David Maib RV-10 #40559 Transition Trainer New Smyrna Beach, FL Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419883#419883 ________________________________ Message 5 _____________________________________ Time: 05:25:02 PM PST US Subject: RV10-List: Re: fuselage rolling rack From: "rvdave" I also have one in Michigan--maybe someone can put it to good use. -------- Dave Ford RV6 flying RV10 building Cadillac, MI Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419890#419890 ________________________________ Message 6 _____________________________________ Time: 06:34:09 PM PST US Subject: RV10-List: Re: Wing tip question From: "Ron B." The RV-14 plans have you use a ratchet strap to pull the wing tip down into the wing at the leading edge. Works well and the wing tips are the same tip supplied with the RV-10. I had no problem doing this installation by myself with the straps. Ron Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419894#419894 ________________________________ Message 7 _____________________________________ Time: 07:35:58 PM PST US From: Kelly McMullen Subject: Re: RV10-List: Re: fuselage rolling rack I have wooden one in Phoenix area, as well as empenage dolly, horizontal stab jig, all available as is, where they sit. On 3/6/2014 6:24 PM, rvdave wrote: > > I also have one in Michigan--maybe someone can put it to good use. > > -------- > Dave Ford > RV6 flying > RV10 building > Cadillac, MI > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=419890#419890 > > ________________________________ Message 8 _____________________________________ Time: 08:21:44 PM PST US Subject: RV10-List: Re: Wing tip question From: "Rocketman1988" Yeah, pushing the wingtip as tight as possible into the leading edge was what generated the 11/16" difference at the TE, in my case... Read this topic online here: http://forums.matronics.com/viewtopic.php?p=419898#419898 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.