---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Tue 02/10/15: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:03 AM - Re: Hose Interference (bill.peyton) 2. 06:20 AM - Re: Re: Hose Interference (Linn Walters) 3. 06:28 AM - Re: Re: Hose Interference (David Clifford) 4. 10:46 AM - Re: Re: Hose Interference (Bill Watson) 5. 10:53 AM - Hose Interference (Rich Hansen) 6. 11:10 AM - Re: Hose Interference (Linn Walters) ________________________________ Message 1 _____________________________________ Time: 06:03:44 AM PST US Subject: RV10-List: Re: Hose Interference From: "bill.peyton" The moment of that extension will put a lot of stress on the output flange of the heat muff. I have never heard of the interference problem before, nor did I have one. -------- Bill WA0SYV Aviation Partners, LLC Read this topic online here: http://forums.matronics.com/viewtopic.php?p=438205#438205 ________________________________ Message 2 _____________________________________ Time: 06:20:05 AM PST US From: Linn Walters Subject: Re: RV10-List: Re: Hose Interference I agree .... I just looked at my installation (I'm still building) and my scat tube doesn't come near interfering with anything. I suspect that the scat tube Rich is installing might be cut too long. My scat tube has a nice, graceful curve from the muff to the heat box. Linn On 2/10/2015 9:00 AM, bill.peyton wrote: > > The moment of that extension will put a lot of stress on the output flange of the heat muff. I have never heard of the interference problem before, nor did I have one. > > -------- > Bill > WA0SYV > Aviation Partners, LLC > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=438205#438205 > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ________________________________ Message 3 _____________________________________ Time: 06:28:03 AM PST US From: David Clifford Subject: Re: RV10-List: Re: Hose Interference No alignment or interference with mine either. ----- Original Message ----- From: "bill.peyton" Sent: Tuesday, February 10, 2015 9:00:38 AM Subject: RV10-List: Re: Hose Interference The moment of that extension will put a lot of stress on the output flange of the heat muff. I have never heard of the interference problem before, nor did I have one. -------- Bill WA0SYV Aviation Partners, LLC Read this topic online here: http://forums.matronics.com/viewtopic.php?p=438205#438205 ________________________________ Message 4 _____________________________________ Time: 10:46:05 AM PST US From: Bill Watson Subject: Re: RV10-List: Re: Hose Interference On 2/10/2015 9:16 AM, Linn Walters wrote: > My scat tube has a nice, graceful curve from the muff to the heat box. Well stated. do not archive ________________________________ Message 5 _____________________________________ Time: 10:53:36 AM PST US From: Rich Hansen Subject: RV10-List: Hose Interference > Bob, agree scat tubing or scat "ducting" per ACS might have been better. Bottom of my page says may not edit your post. Bill, many have complained that the heat coming out of the front box is a bit much. Possibly the 90 degree bend will decelerate the air flow creating a positive outcome, but it is highly doubtful that it will cause the flange welds to be ripped out of the heat muff. Is that what you meant? Linn, in fitting this left side scat I started with a longer than desired piece. Then progressively cut it down about an inch at a time, refitting and rechecking, each time with an undesirable outcome. For my application it was: if I clear the fuel line it hits the cooler, if I clear the cooler it hits the fuel line, etc. Look at Section FF6, page 5 in the plans. In the bottom middle picture it looks like the scat may be hitting/rubbing against the oil cooler right behind the crossover bracket. My plans are old & maybe things have changed. But, that's about what I was dealing with. Wasn't interested in RTVing Air Seal Fabric onto the hose as suggested on previous page. Also, I should add that I do have SS aftermarket heat boxes and aftermarket cooler, although I'm pretty sure their dimensions are the same as factory. Regarding the fuel line, we probably all have somewhat similar installations, yet each will be slightly different in routing, securing and final fit. Didn't mean to stir the pot or create a problem for anyone, just offering up a suggestion for fellow builders that appears to be a solution, not too expensive, and/or that the elbow might be used somewhere else in someone's build - experimental! PS: a 45 degree would be even better Rich Hansen > > > > > > > > > > > > > > > > > > > > > ________________________________ Message 6 _____________________________________ Time: 11:10:47 AM PST US From: Linn Walters Subject: Re: RV10-List: Hose Interference On 2/10/2015 1:50 PM, Rich Hansen wrote: > > >> Bob, agree scat tubing or scat "ducting" per ACS might have been better. Bottom of my page says may not edit your post. > Bill, many have complained that the heat coming out of the front box is a bit much. You can cover some of the muff inlet on the baffle with some metal tape to cut down the flow of air. My Grumman came from the factory that way with no ill effects. I used red RTV to glue a thin sheet of RTV on the heat valve to help seal off the port through the firewall. Linn do not archive > snip > > Rich Hansen >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.