Today's Message Index:
----------------------
1. 02:15 AM - Re: Fuel injection servo attachment - concerned ? (Gordon Anderson)
2. 06:54 AM - Re: Re: Fuel injection servo attachment - concerned ? (Jesse Saint)
3. 07:13 AM - Re: Re: Fuel injection servo attachment - concerned ? (Carl Froehlich)
4. 12:56 PM - Re: Fuel injection servo attachment - concerned ? (Gordon Anderson)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel injection servo attachment - concerned ? |
I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to the engine,
but cannot find any instructions or hardware. Only the nuts and plain
washers holding the plastic "preservation" cover plate on the sump together with
a blind gasket were supplied with the engine & servo.
Lycoming Service Instruction 1484C gives the torques to "refer to the Parts Catalogue
for the correct washers, lock washers, nuts, gaskets and spacers"
Can anyone provide a copy of the relevant page in the Lycoming parts catalogue?
Assuming a gasket is required, is it normal to use one both above and below the
control cable bracket?
Gordon Anderson
Switzerland
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=442185#442185
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel injection servo attachment - concerned ? |
You want a gasket on both sides of the bracket and you want lock washers under
the nuts holding the servo on. The hardware, IIRC, should have been included with
the FWF kit.
Jesse Saint
Saint Aviation, Inc.
352-427-0285
jesse@saintaviation.com
Sent from my iPad
> On May 17, 2015, at 5:12 AM, Gordon Anderson <mregoan@hispeed.ch> wrote:
>
>
> I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to the
engine, but cannot find any instructions or hardware. Only the nuts and plain
washers holding the plastic "preservation" cover plate on the sump together
with a blind gasket were supplied with the engine & servo.
>
> Lycoming Service Instruction 1484C gives the torques to "refer to the Parts Catalogue
for the correct washers, lock washers, nuts, gaskets and spacers"
>
> Can anyone provide a copy of the relevant page in the Lycoming parts catalogue?
>
> Assuming a gasket is required, is it normal to use one both above and below the
control cable bracket?
>
> Gordon Anderson
> Switzerland
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=442185#442185
>
>
>
>
>
>
>
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel injection servo attachment - concerned ? |
You might want to look again. Hardware and gaskets should be in a bag that
came with the engine. If it is not there give Van's a call.
Yes - a gasket goes on each side of the control cable bracket. If memory
serves, the bracket came with a gasket.
Carl
-----Original Message-----
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Gordon Anderson
Sent: Sunday, May 17, 2015 5:13 AM
Subject: RV10-List: Re: Fuel injection servo attachment - concerned ?
I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to
the engine, but cannot find any instructions or hardware. Only the nuts and
plain washers holding the plastic "preservation" cover plate on the sump
together with a blind gasket were supplied with the engine & servo.
Lycoming Service Instruction 1484C gives the torques to "refer to the Parts
Catalogue for the correct washers, lock washers, nuts, gaskets and spacers"
Can anyone provide a copy of the relevant page in the Lycoming parts
catalogue?
Assuming a gasket is required, is it normal to use one both above and below
the control cable bracket?
Gordon Anderson
Switzerland
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=442185#442185
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Fuel injection servo attachment - concerned ? |
Carl, Jesse, thanks a lot for challenging me to go look again. Now I managed to
find the hardware and gasket. Definitely time for some 5S in the workshop.
Cheers,
Gordon
Do not archive
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=442198#442198
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|