---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Sun 05/17/15: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:15 AM - Re: Fuel injection servo attachment - concerned ? (Gordon Anderson) 2. 06:54 AM - Re: Re: Fuel injection servo attachment - concerned ? (Jesse Saint) 3. 07:13 AM - Re: Re: Fuel injection servo attachment - concerned ? (Carl Froehlich) 4. 12:56 PM - Re: Fuel injection servo attachment - concerned ? (Gordon Anderson) ________________________________ Message 1 _____________________________________ Time: 02:15:26 AM PST US Subject: RV10-List: Re: Fuel injection servo attachment - concerned ? From: "Gordon Anderson" I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to the engine, but cannot find any instructions or hardware. Only the nuts and plain washers holding the plastic "preservation" cover plate on the sump together with a blind gasket were supplied with the engine & servo. Lycoming Service Instruction 1484C gives the torques to "refer to the Parts Catalogue for the correct washers, lock washers, nuts, gaskets and spacers" Can anyone provide a copy of the relevant page in the Lycoming parts catalogue? Assuming a gasket is required, is it normal to use one both above and below the control cable bracket? Gordon Anderson Switzerland Read this topic online here: http://forums.matronics.com/viewtopic.php?p=442185#442185 ________________________________ Message 2 _____________________________________ Time: 06:54:25 AM PST US From: Jesse Saint Subject: Re: RV10-List: Re: Fuel injection servo attachment - concerned ? You want a gasket on both sides of the bracket and you want lock washers under the nuts holding the servo on. The hardware, IIRC, should have been included with the FWF kit. Jesse Saint Saint Aviation, Inc. 352-427-0285 jesse@saintaviation.com Sent from my iPad > On May 17, 2015, at 5:12 AM, Gordon Anderson wrote: > > > I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to the engine, but cannot find any instructions or hardware. Only the nuts and plain washers holding the plastic "preservation" cover plate on the sump together with a blind gasket were supplied with the engine & servo. > > Lycoming Service Instruction 1484C gives the torques to "refer to the Parts Catalogue for the correct washers, lock washers, nuts, gaskets and spacers" > > Can anyone provide a copy of the relevant page in the Lycoming parts catalogue? > > Assuming a gasket is required, is it normal to use one both above and below the control cable bracket? > > Gordon Anderson > Switzerland > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=442185#442185 > > > > > > > > > > ________________________________ Message 3 _____________________________________ Time: 07:13:52 AM PST US From: "Carl Froehlich" Subject: RE: RV10-List: Re: Fuel injection servo attachment - concerned ? You might want to look again. Hardware and gaskets should be in a bag that came with the engine. If it is not there give Van's a call. Yes - a gasket goes on each side of the control cable bracket. If memory serves, the bracket came with a gasket. Carl -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Gordon Anderson Sent: Sunday, May 17, 2015 5:13 AM Subject: RV10-List: Re: Fuel injection servo attachment - concerned ? I have the Van's Lycoming IO-540 and am ready to attach the fuel servo to the engine, but cannot find any instructions or hardware. Only the nuts and plain washers holding the plastic "preservation" cover plate on the sump together with a blind gasket were supplied with the engine & servo. Lycoming Service Instruction 1484C gives the torques to "refer to the Parts Catalogue for the correct washers, lock washers, nuts, gaskets and spacers" Can anyone provide a copy of the relevant page in the Lycoming parts catalogue? Assuming a gasket is required, is it normal to use one both above and below the control cable bracket? Gordon Anderson Switzerland Read this topic online here: http://forums.matronics.com/viewtopic.php?p=442185#442185 ________________________________ Message 4 _____________________________________ Time: 12:56:30 PM PST US Subject: RV10-List: Re: Fuel injection servo attachment - concerned ? From: "Gordon Anderson" Carl, Jesse, thanks a lot for challenging me to go look again. Now I managed to find the hardware and gasket. Definitely time for some 5S in the workshop. Cheers, Gordon Do not archive Read this topic online here: http://forums.matronics.com/viewtopic.php?p=442198#442198 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.