---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Mon 10/12/15: 10 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:06 AM - RV-10 Wing and Fuselage Jig (Rich Hansen) 2. 08:24 AM - Re: RV-10 Wing and Fuselage Jig (Kelly McMullen) 3. 09:27 AM - Re: Re: Fuel Sender - Installation/Sealing (Jae Chang) 4. 09:59 AM - Re: RV-10 Wing and Fuselage Jig (Rich Hansen) 5. 10:16 AM - Re: Fuel Sender - Installation/Sealing (Lenny Iszak) 6. 11:47 AM - Re: Re: Fuel Sender - Installation/Sealing (Werner Schneider) 7. 01:41 PM - Re: Question control system WD-1011 Page 39-8 Fig 3 (Rich Hansen) 8. 02:24 PM - Re: Re: Question control system WD-1011 Page 39-8 Fig 3 (Werner Schneider) 9. 08:03 PM - Re: Fuel Sender - Installation/Sealing (rv10flyer) 10. 08:10 PM - Re: Nose Gear Fairing (rv10flyer) ________________________________ Message 1 _____________________________________ Time: 08:06:36 AM PST US Subject: RV10-List: RV-10 Wing and Fuselage Jig From: Rich Hansen Time to get organized & clear out the hanger. Have a wing storage stand (top skins will face one another leaving you the ability to leave bottom wing skins off for later addition of wiring/auto pilot/pitot system etc). The stand has fixed position wheels at one end and caster wheels at opposite end. Also have fuselage jig with all hardware and hole protection inserts, and pneumatic tires for easy moving fuselage assy anywhere quickly in your garage while keeping it at a nice workable level. Both located at So Cal French Valley Airport. $65 for both, come and pick em up! 925-918-0826 ________________________________ Message 2 _____________________________________ Time: 08:24:55 AM PST US Subject: Re: RV10-List: RV-10 Wing and Fuselage Jig From: Kelly McMullen While I have given away my wing stand, still have empennage cradle on wheels, horizontal stab jig, and fuselage cradle, in the Phoenix area, free to anyone that wants to pick them up. On Mon, Oct 12, 2015 at 8:03 AM, Rich Hansen wrote: > Time to get organized & clear out the hanger. Have a wing storage stand > (top skins will face one another leaving you the ability to leave bottom > wing skins off for later addition of wiring/auto pilot/pitot system etc). > The stand has fixed position wheels at one end and caster wheels at > opposite end. > > Also have fuselage jig with all hardware and hole protection inserts, and > pneumatic tires for easy moving fuselage assy anywhere quickly in your > garage while keeping it at a nice workable level. Both located at So Cal > French Valley Airport. $65 for both, come and pick em up! 925-918-0826 > > > * > > > * > > ________________________________ Message 3 _____________________________________ Time: 09:27:42 AM PST US Subject: Re: RV10-List: Re: Fuel Sender - Installation/Sealing From: Jae Chang You have to be careful with EZ Turn and not use too much. otherwise, you will find EZ Turn blobs potentially clogging your fuel lines and filters. On 10/10/2015 9:48 PM, Phillip Perry wrote: > Thanks for all the info. I'll just slather the rubber gaskets up with > EZ Turn and give them shot. > > Thanks again, > Phil > > ________________________________ Message 4 _____________________________________ Time: 09:59:35 AM PST US Subject: RV10-List: Re: RV-10 Wing and Fuselage Jig From: "Rich Hansen" Here's a couple pictures of the jigs. -------- Rich Hansen RV-6A RV-10 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=447844#447844 Attachments: http://forums.matronics.com//files/rollingfusejig_167.jpg http://forums.matronics.com//files/wingjig_162.jpg ________________________________ Message 5 _____________________________________ Time: 10:16:48 AM PST US Subject: RV10-List: Re: Fuel Sender - Installation/Sealing From: "Lenny Iszak" I used a viton gasket and screws with built-in viton orings. McMaster has them. I can get you part numbers if you want to go with that setup. A friend of mine uses these senders on boats he builds and he says the original rubber gaskets are junk. Lenny Read this topic online here: http://forums.matronics.com/viewtopic.php?p=447845#447845 ________________________________ Message 6 _____________________________________ Time: 11:47:33 AM PST US Subject: Re: RV10-List: Re: Fuel Sender - Installation/Sealing From: Werner Schneider Lenny I would love to see the part numbers thanks. Just keep in mind Avgas is not as bad to rubber then Mogas will.... Cheers Werner On 12.10.2015 19:13, Lenny Iszak wrote: > > I used a viton gasket and screws with built-in viton orings. McMaster has them. I can get you part numbers ________________________________ Message 7 _____________________________________ Time: 01:41:36 PM PST US Subject: RV10-List: Re: Question control system WD-1011 Page 39-8 Fig 3 From: "Rich Hansen" Werner, Just went through the exact same issue a few weeks ago. I just used two of the smaller washers on the forward side of the rod end bearing and one on the aft end, all captured inside of the weldament. I'm not even sure I had to use an "L" washer on the outside - and used the stock called for bolt. Plenty of threads still remained. Worked fine, no rubbing, no issues. You might consider using a larger O/D washer on the most fwd side, so as to minimize the fwd/aft movement of the push rod should the bearing separate from inside of the rod end - it is still captured inside of the welded sleeves no matter what. Although I think one could take up the slack by tightening the AN bolt/nut, this would undesirably stress the area (mounting sleeves) for no reason. Am going out to hanger today and will double check - any change I'll let you know.... Also, please let us know what Vans says. Maybe they made some changes and we need to make some changes as well! Rich RV-6A 1000+ hrs, sold RV-10 close to cranking -------- Rich Hansen RV-6A RV-10 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=447849#447849 ________________________________ Message 8 _____________________________________ Time: 02:24:19 PM PST US Subject: Re: RV10-List: Re: Question control system WD-1011 Page 39-8 Fig 3 From: Werner Schneider Thanks Rich, I actually went along as Jesse said 1h ago, torqued with 25 in lbs and indeed it did close the gap and clamp all together, after the 2nd screw I had to retorque the 1st one a 2nd time. This puts some bending on the flanges, I will wait to hear from Van's but think with that low pressure there is no harm, I was not expecting that I could close with that little torque the gap. Cheers Werner On 12.10.2015 22:38, Rich Hansen wrote: > > Werner, > Just went through the exact same issue a few weeks ago. I just used two of the smaller washers on the forward .......... ________________________________ Message 9 _____________________________________ Time: 08:03:40 PM PST US Subject: RV10-List: Re: Fuel Sender - Installation/Sealing From: "rv10flyer" I used proseal, just like we used in the military. -------- Wayne G. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=447855#447855 ________________________________ Message 10 ____________________________________ Time: 08:10:42 PM PST US Subject: RV10-List: Re: Nose Gear Fairing From: "rv10flyer" I'd put longer bolts and bushings in there, so that fairing gets damaged less by tow bars. It will be fine. None of them fly perfect, so don't sweat it. -------- Wayne G. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=447856#447856 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.