Today's Message Index:
----------------------
1. 11:35 AM - Re: GARMIN autopilot servos wiring (Carlos Trigo)
2. 12:28 PM - Re: GARMIN autopilot servos wiring (Stein Bruch)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: GARMIN autopilot servos wiring |
Thank you Stein
I believe the DYNON servo wires are all unshielded.
Why do you recommend the CAN, the RS-232 and the trim wires to be shielded?
Best
Carlos
Enviado do meu iPhone
No dia 30/03/2016, s 10:39, Stein Bruch <stein@steinair.com> escreveu:
>
> You would use shielded multi conductor wires for the CAN portion and
> RS-232's (and possibly some trim), but individual wires for the CWS, PWR,
> GND, and CAN termination (if you're using it for the terminator on the CAN).
>
>
> Cheers,
> Stein
>
>
> -----Original Message-----
> From: owner-rv10-list-server@matronics.com
> [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Carlos Trigo
> Sent: Tuesday, March 29, 2016 8:21 PM
> To: rv10-list@matronics.com
> Subject: RV10-List: GARMIN autopilot servos wiring
>
>
> Guys
>
> Those of you who installed or are installing a GARMIN G3X, which wires or
> multi-wire cable did you use to connect the autopilot servos?
>
> Thanks
> Carlos
>
> Enviado do meu iPhone
>
>
>
>
>
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | GARMIN autopilot servos wiring |
Because it's what Garmin recommends in their manual! :)
That said, it is recommended to be shielded just to keep "noise" to a minimum,
but we actually have seen people retrofit both TruTrak and Dynon Autopilots with
the Garmin Servos, re-use their existing wiring with no ill effects. Of course
it's always best to follow the manufacturer recommendations, but we have
seen people do it the other way and have acceptable results....we've also seen
people have unacceptable results as well though (so fair warning).
Cheers,
Stein
-----Original Message-----
From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Carlos Trigo
Sent: Thursday, March 31, 2016 1:32 PM
Subject: Re: RV10-List: GARMIN autopilot servos wiring
Thank you Stein
I believe the DYNON servo wires are all unshielded.
Why do you recommend the CAN, the RS-232 and the trim wires to be shielded?
Best
Carlos
Enviado do meu iPhone
No dia 30/03/2016, s 10:39, Stein Bruch <stein@steinair.com> escreveu:
>
> You would use shielded multi conductor wires for the CAN portion and
> RS-232's (and possibly some trim), but individual wires for the CWS,
> PWR, GND, and CAN termination (if you're using it for the terminator on the CAN).
>
>
> Cheers,
> Stein
>
>
> -----Original Message-----
> From: owner-rv10-list-server@matronics.com
> [mailto:owner-rv10-list-server@matronics.com] On Behalf Of Carlos
> Trigo
> Sent: Tuesday, March 29, 2016 8:21 PM
> To: rv10-list@matronics.com
> Subject: RV10-List: GARMIN autopilot servos wiring
>
>
> Guys
>
> Those of you who installed or are installing a GARMIN G3X, which wires
> or multi-wire cable did you use to connect the autopilot servos?
>
> Thanks
> Carlos
>
> Enviado do meu iPhone
>
>
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|