Today's Message Index:
----------------------
1. 06:58 PM - Trim Cable Nut (mhealydds)
2. 07:15 PM - Re: Trim Cable Nut (David Maib)
3. 07:25 PM - Re: Trim Cable Nut (Jesse Saint)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
This may seem like a dumb question.....how did you get the elevator trim cable
nut that is riveted to elevator cover plate threaded onto elevator trim control
cable. I don't seem to have enough room to twist cover plate with nut around
trim cable without elevator in the way.
Thanks.....Matt
(getting excited as end is in sight!)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=459501#459501
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Trim Cable Nut |
I installed #4 screws and nuts in lieu of riveting. I've been glad several times
over the past 8 years.
David Maib
> On Aug 14, 2016, at 9:56 PM, mhealydds <mhealydds@gmail.com> wrote:
>
>
> This may seem like a dumb question.....how did you get the elevator trim cable
nut that is riveted to elevator cover plate threaded onto elevator trim control
cable. I don't seem to have enough room to twist cover plate with nut around
trim cable without elevator in the way.
>
> Thanks.....Matt
>
> (getting excited as end is in sight!)
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=459501#459501
>
>
>
>
>
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Trim Cable Nut |
If you unscrew the screws holding the trim system onto the HS deck, you can pull
out on one trim cable enough to bend it out of the hole in the elevator and
screw the nut and plate on. Then do the same on the other side.
Jesse Saint
Saint Aviation, Inc.
jesse@saintaviation.com
C: 352-427-0285
F: 815-377-3694
Sent from my iPhone
> On Aug 14, 2016, at 10:14 PM, David Maib <dmaib@me.com> wrote:
>
>
> I installed #4 screws and nuts in lieu of riveting. I've been glad several times
over the past 8 years.
>
> David Maib
>
>
>> On Aug 14, 2016, at 9:56 PM, mhealydds <mhealydds@gmail.com> wrote:
>>
>>
>> This may seem like a dumb question.....how did you get the elevator trim cable
nut that is riveted to elevator cover plate threaded onto elevator trim control
cable. I don't seem to have enough room to twist cover plate with nut around
trim cable without elevator in the way.
>>
>> Thanks.....Matt
>>
>> (getting excited as end is in sight!)
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=459501#459501
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|