Today's Message Index:
----------------------
1. 07:19 AM - Re: RV10 (tony Dubeansky)
2. 10:34 AM - Re: What flap setting do you use for takeoff (Mike Whisky)
3. 11:50 AM - Re: Re: What flap setting do you use for takeoff (Werner Schneider)
4. 12:09 PM - Re: What flap setting do you use for takeoff (Mike Whisky)
5. 12:34 PM - Re: Re: What flap setting do you use for takeoff (Werner Schneider)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thank you, Jesse and Kelly for your reply. I have been asking anyone and everyone
about the counterweights dilemma, including several engine builders for over
three years. There comes a time when you have to crap or get off the pot. After
about twelve hours of frustration the counterweights have been removed and
the new ones reinstalled. As far as electronic ignition is concerned, there is
no point in turning back. I sold the mags, electronic ignition is paid for and
the weights have been changed. Unless there is a safety issue concerning the
quality of the system I am going to keep it. If anyone has heard of any failures,
I'd appreciate hearing from you. I am still looking for a flywheel that
will work with the system and my engine. Thanks again for any and all help.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: What flap setting do you use for takeoff |
Attached my Vx / Vy measurements during Phase I it was done with flaps 0 degrees.
Would be interesting to see what it would be with 10 or 15 degrees.
Regards
Mike
--------
RV-10 builder (flying)
#511
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=463888#463888
Attachments:
http://forums.matronics.com//files/img_0333_606.png
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: What flap setting do you use for takeoff |
Mike, just redo your testflights and send the data to Andre :) and then
you will know.
Cheers Werner
On 13.12.2016 19:33, Mike Whisky wrote:
>
> Attached my Vx / Vy measurements during Phase I it was done with flaps 0 degrees.
Would be interesting to see what it would be with 10 or 15 degrees.
> Regards
> Mike
>
> --------
> RV-10 builder (flying)
> #511
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: What flap setting do you use for takeoff |
Great idea if I ever find the time but an even better suggestion you do it during
your Phase 1, just get the -10 done quickly
--------
RV-10 builder (flying)
#511
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=463891#463891
Attachments:
http://forums.matronics.com//files/img_0293_511.jpg
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: What flap setting do you use for takeoff |
I would do that for you but might need help for finishing the remaining
90% :)
But wait, there is Gordon he should be close ;)
Cheers
Werner
On 13.12.2016 21:07, Mike Whisky wrote:
>
> Great idea if I ever find the time but an even better suggestion you do it during
your Phase 1, just get the -10 done quickly
>
> --------
> RV-10 builder (flying)
> #511
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=463891#463891
>
>
> Attachments:
>
> http://forums.matronics.com//files/img_0293_511.jpg
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|